Chapter 1 Administration

Chapter 2 Definitions

Chapter 3 Use and Occupancy Classification

Chapter 4 Special Detailed Requirements Based on Use and Occupancy

Chapter 5 General Building Heights and Areas; Separation of Occupancies

Chapter 6 Types of Construction

Chapter 7 Fire-Resistance-Rated Construction

Chapter 8 Interior Finishes

Chapter 9 Fire Protection Systems

Chapter 10 Means of Egress

Chapter 11 Accessibility

Chapter 12 Interior Environment

Chapter 13 Energy Efficiency

Chapter 14 Exterior Walls

Chapter 15 Roof Assemblies and Rooftop Structures

Chapter 16 Structural Design

Chapter 17 Structural Tests and Special Inspections

Chapter 18 Soils and Foundations

Chapter 19 Concrete

Chapter 20 Aluminum

Chapter 21 Masonry

Chapter 22 Steel

Chapter 23 Wood

Chapter 24 Glass and Glazing

Chapter 25 Gypsum Board and Plaster

Chapter 26 Plastic

Chapter 27 Electrical

Chapter 28 Mechanical Systems

Chapter 29 Plumbing Systems

Chapter 30 Elevators and Conveying Systems

Chapter 31 Special Construction

Chapter 32 Encroachments Into the Public Right-Of-Way

Chapter 33 Safeguards During Construction or Demolition

Chapter 34 Reserved

Chapter 35 Referenced Standards [PDF]

Appendix A Reserved

Appendix B Reserved

Appendix C Reserved

Appendix D Fire Districts

Appendix E Supplementary Accessibility Requirements

Appendix F Rodent Proofing

Appendix G Flood-Resistant Construction

Appendix H Outdoor Signs

Appendix I Reserved

Appendix J Reserved

Appendix K Modified Industry Standards for Elevators and Conveying Systems

Appendix L Reserved

Appendix M Supplementary Requirements for One- And Two-Family Dwellings

Appendix O Reserved

Appendix N Assistive Listening Systems Performance Standards

Appendix P R-2 Occupancy Toilet and Bathing Facilities Requirements

Appendix Q Modified National Standards for Automatic Sprinkler, Standpipe, and Fire Alarm Systems

Appendix R Acoustical Tile and Lay-In Panel Ceiling Suspension Systems

Get access to the 125 NYC DOB linked resources for NYC Building Code 2008 that we've compiled so far.
LEARN MORE
Continue without linked resources
AA Aluminum Association
900 -19th Street N.W., Suite 300
Washington, DC 20006
Standard
Reference
Number
Title
ADM 1 — 00 Aluminum Design Manual: Part 1-A Aluminum Structures, Allowable Stress Design; and Part 1-B
   —Aluminum Structures, Load and Resistance Factor Design of Buildings and Similar Type Structures
ASM 35 — 80. Aluminum Sheet Metal Work in Building Construction
AAMA American Architectural Manufacturers Association
1827 Waldon Office Square, Suite 104
Schaumburg, IL 60173
Standard
Reference
Number
Title
1402—86 Standard Specifications for Aluminum Siding, Soffit and Fascia
101/I.S.2—97 Voluntary Specifications for Aluminum, Vinyl (PVC) and Wood Windows and Glass Doors
101/I.S.2/NAFS—02 Voluntary Performance Specification for Window, Skylights and Glass Doors
ACI American ConcreteInstitute
P.O. Box 9094
Farmington Hills, MI 48333-9094
Standard
Reference
Number
Title
216.1—97 Standard Method for Determining Fire Resistance of Concrete and Masonry Construction Assemblies
318—02 Building Code Requirements for Structural Concrete
530—02 Building Code Requirements for Masonry Structures
530.1—02 Specifications for Masonry Structures
TG/T1.1—01 Acceptance Criteria for Moment Frames Based on Testing
AF&PA American Forest & Paper Association
1111 19th St, NW Suite 800
Washington, DC 20036
Standard
Reference
Number
Title
AF&PA/ASCE 16—95 Standard for Load and Resistance Factor Design (LRFD) for Engineered Wood Construction
WCD No. 4—89 Plank and Beam Framing for Residential Buildings
WFCM—01 Frame Construction Manual for One-and Two-family Dwellings
T.R. No. 7—87 Basic Requirements for Permanent Wood Foundation System.
NDS—01 National Design Specification (NDS) for Wood Construction with 2001 Supplement
AF&PA—93 Span Tables for Joists and Rafters
AHA American Hardwood Association
1210 West N.W. Highway
Palatine, IL 60067
Standard
Reference
Number
Title
A135.4—95 Basic Hardboard
A135.5—95 Prefinished Hardboard Paneling.
A135.6—98 Hardboard Siding
A194.1—85 Cellulosic Fiber Board
AISC American Institute of Steel Construction
One East Wacker Drive, Suite 3100
Chicago, IL 60601-2001
Standard
Reference
Number
Title
335—89s1 Specification for Structural Steel Buildings—Allowable Stress Design and Plastic Design, including Supplement No.1, 2001
LRFD (1999) Load and Resistance Factor Design Specification for Structural Steel Buildings
HSS (2000) Load and Resistance Factor Design Specification for Steel Hollow Structural Sections
341—02 Seismic Provisions for Structural Steel Buildings
AISI American Iron and Steel Institute
1140 Connecticut Avenue
Suite 705
Washington, DC 20036
Standard
Reference
Number
Title
NASPEC 2001 North American Specification for Design of Cold-Formed Steel Structural Members
General Standard for Cold-Formed Steel Framing-General Provisions, 2001
Header Standard for Cold-Formed Steel Framing-Header Design, 2001
Truss Standard for Cold-Formed Steel Framing-Truss Design, 2001
AITC American Institute of Timber Construction
Suite 140
7012 S. Revere Parkway
Englewood, CO 80112
Standard
Reference
Number
Title
AITC A 190.1—92 Structural Glued Laminated Timber
AITC Technical Note 7
—96
Calculation of Fire Resistance of Glued Laminated Timbers
AITC 104—84 Typical Construction Details
AITC 110—01 Standard Appearance Grades for Structural Glued Laminated Timber
AITC 112—93 Standard for Tongue-and-Groove Heavy Timber Roof Decking
AITC 113—01 Standard for Dimensions of Structural Glued Laminated Timber
AITC 117—01 Standard Specifications for Structural Glued Laminated Timber of Softwood Species—
   Design Requirements—Standard Specifications for Structural Glued Laminated Timber of Softwood Species
  —Manufacturing,Requirement
AITC 119—96 Standard Specifications for Structural Glued Laminated Timber of Hardwood Species
AITC 200—92 Inspection Manual
AITC 500—91 Determination of Design Values for Structural Glued Laminated Timber
ALI Automotive Lift Institute
P.O. Box 33116
Indialantic, FL 32903-3116
Standard
Reference
Number
Title
ALI ALCTV—98 Standard for Automotive Lifts—Safety Requirements for Construction, Testing and Validation (ANSI)
ANSI American National Standards Institute
25 West 43rd Street, Fourth Floor
New York, NY 10036
Standard
Reference
Number
Title
A 13.1—96 Scheme for the Identification of Piping Systems
A 42.2—71 Portland Cement and Portland Cement Lime Plastering, Exterior (Stucco) and Interior
A 42.3—71 Lathing and Furring for Portland Cement and Portland Cement Lime Plastering, Exterior Stucco and Interior
A108.1A—99 Installation of Ceramic Tile in the Wet-set Method, with Portland Cement Mortar
A108.1B—99 Installation of Ceramic Tile, Quarry Tile on a Cured Portland Cement Mortar Setting Bed with Dry-set or Latex-Portland Mortar
A108.4—99 Installation of Ceramic Tile with Organic Adhesives or Water-cleanable Tile-Setting Epoxy Adhesive
A108.5—99 Installation of Ceramic Tile with Dry-set Portland Cement Mortar or Latex Portland Cement Mortar
A108.6—99 Installation of Ceramic Tile with Chemical-resistant, Water Cleanable Tile-setting-and-grouting Epoxy
A108.7—92 Specification for Electrically Conductive Ceramic Tile Installed with Conductive Dry-set Portland Cement Mortar
A108.8—99 Installation of Ceramic Tile with Chemical-resistant Furan Resin Mortar and Grout
A108.9—99 Installation of Ceramic Tile with Modified Epoxy Emulsion Mortar/Grout
A 108.10—99 Installation of Grout in Tilework
A 118.1—99 American National Standard Specifications for Dry-set Portland Cement Mortar
A 118.2—99 American National Standard Specifications for Conductive Dry-set Portland Cement Mortar
A 118.3—99 American National Standard Specifications for Chemical-resistant, Water-cleanable Tile-setting and -Grouting Epoxy and
   Water Cleanable Tile-setting Epoxy Adhesive
A 118.4—99 American National Standard Specifications for Latex-portland Cement Mortar
A 118.5—99 American National Standard Specifications for Chemical Resistant Furan Mortar and Grouts for Tile Installation
A 118.6—99 American National Standard Specifications for Cement Grouts for Tile Installation
A 118.8—99 American National Standard Specifications for Modified Epoxy Emulsion Mortar/Grout
A 136.1—99 American National Standard Specifications for Organic Adhesives for Installation of Ceramic Tile
A 137.1—88 American National Standard Specifications for Ceramic Tile
A 208.1—99 Particleboard
B 31.3—99 Process Piping—Including Addendum
Z 97.1—84 (R1994) Safety Glazing Materials Used in Buildings-safety Performance Specifications and
   Methods of Test (Reaffirmed 1994)
APA APA -Engineered Wood Association
P.O. Box 11700
Tacoma, WA 98411-0700
Standard
Reference
Number
Title
APA PDS—97 Plywood Design Specification (revised 1998)
APA PDS Supplement 1—
90
Design and Fabrication of Plywood Curved Panels (revised 1995)
APA PDS Supplement 2—
92.
Design and Fabrication of Plywood-lumber beams (revised 1998
APA PDS Supplement 3—
90
Design and Fabrication of Plywood Stressed-skin Panels (revised 1996)
APA PDS Supplement 4—
90.
Design and Fabrication of Plywood Sandwich Panels (revised 1993)
APA PDS Supplement 5—
95
Design and Fabrication of All-plywood Beams (revised 1995)
EWS R540—96 Builders Tips: Proper Storage and Handling of Glulam Beams
EWS S475—99 Glued Laminated Beam Design Tables
EWS S560—99 Field Notching and Drilling of Glued Laminated Timber Beams
EWS T300—99 Glulam Connection Details
EWS X440—00 Product Guide-Glulam
EWS X445—97 Glulam in Residential Construction —Southern Edition
EWS X450—97 Glulam in Residential Construction —Western Edition
ASAE American Society of Agricultural Engineers
2950 Niles Road
St. Joseph, MI 49085-9659
Standard
Reference
Number
Title
EP 484.2 (1998) Diaphragm Design of Metal-Clad, Post-Frame Rectangular Buildings
EP 486.1 (2000) Shallow-Post Foundation Design
EP 559 (1997) Design Requirements and Bending Properties for Mechanically Laminated Columns
ASCE/SEI American Society of Civil Engineers
Structural Engineering Institute
1801 Alexander Bell Drive
Reston, VA 20191-4400
Standard
Reference
Number
Title
3—91 Standard Practice for the Construction and Inspection of Composite Slabs
5—02 Building Code Requirements for Masonry Structures
6—02 Specifications for Masonry Structures
7—02 Minimum Design Loads for Buildings and Other Structures
8—90 Standard Specification for the Design of Cold-formed Stainless Steel Structural Members
16—95 Standard for Load Resistance Factor Design (LRFD) for Engineered Wood Construction
19—96 Structural Applications of Steel Cables for Buildings
24—05* Flood Resistant Design and Construction
29—99 Standard Calculation Methods for Structural Fire Protection
32—01 Design and Construction of Frost Protected Shallow Foundations
*As modified in Appendix G
ASME American Society of Mechanical Engineers
Three Park Avenue
New York, NY 10016-5990
Standard
Reference
Number
Title
A17.1—00* with
supplements A17.1a—02
and A17.1b—03
Safety Code for Elevators and Escalators
A18.1—99 Safety Standard for Platform Lifts and Stairway Chairlifts—with Addenda A18.1a-2001
B16.18—84 (R1994) Cast Copper Alloy Solder Joint Pressure Fittings
B16.22—95 Wrought Copper and Copper Alloy Solder Joint Pressure Fittings—with Addenda B16.22a-98
B20.1—03* Safety Standard for Conveyors and Related Equipment
*As modified in Appendix K
ASTM ASTM International
100 Barr Harbor Drive
West Conshohocken, PA 19428-2959
Standard
Reference
Number
Title
A 6/A 6M—01b Specification for General Requirements for Rolled Steel, Structural Steel Bars,Plates, Shapes, and Sheet Piling
A 36/A 36M—00 Specification for Carbon Structural Steel
A 82—01 Specification for Steel Wire, Plain, for Concrete Reinforcement
A 123/A 123M—97e1 Specification for Zinc (Hot-Dip Galvanized) Coating on Iron and Steel Products
A 153—01a Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware.
A 167—99 Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet and Strip
A 185—01 Specification for Steel Welded Wire Reinforcement, Plain for Concrete
A 252—E01 Specification for Welded and Seamless Steel Pipe Piles
A 283/A 283M—00 Specification for Low and Intermediate Tensile Strength Carbon Steel Plates
A 307—00 Specification for Carbon Steel Bolts and Studs, 60,000 psi Tensile Strength
A 416—99 Specification for Steel Strand, Uncoated Seven-Wire for Prestressed Concrete
A 421/A 421M—98 Specification for Uncoated Stress-Relieved Steel Wire for Prestressed Concrete
A 435/A 435M—90 (2001) Specification for Straight-Beam Ultrasonic Examination of Steel Plates
A 496—01 Specification for Steel Wire, Deformed for Concrete Reinforcement
A 510—00 Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel
A 568/A 568M—01 Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy, Hot-Rolled and,Cold-Rolled, General Requirements for
A 572/A 572M—01 Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel
A 588/A 588M—01 Specification for High-Strength Low-Alloy Structural Steel with 50 ksi (345 Mpa) Minimum Yield Point to 4 inches (100 mm),
   Thick
A 615/A 615M—00 Specification for Deformed and Plain Billet-Steel Bars for Concrete Reinforcement
A 641/A 641M—98 Specification for Zinc-coated (Galvanized) Carbon Steel Wire
A 653/A 653M—01a Specification for Steel Sheet, Zinc-coated Galvanized or Zinc-iron Alloy-Coated Galvannealed by the Hot-dip Process
A 706/A 706M—00 Specification for Low-Alloy Steel Deformed and Plain Bars for Concrete Reinforcement
A 706/A 706M—01 Specification for Low-Alloy Steel Deformed and Plain Bars for Concrete Reinforcement
A 722/A 722M—98 Specification for Uncoated High-Strength Steel Bar for Prestressing Concrete
A 755/A 755M—01 Specification for Steel Sheet, Metallic-Coated by the Hot-Dip Process and Prepainted,by the Coil-Coating Process for Exterior
   Exposed Building Products
A 767/A 767M—00b Specification for Zinc-coated (Galvanized) Steel Bars for Concrete Reinforcement
A 775/A 775M—01 Specification for Epoxy-Coated Steel Reinforcing Bars
A 792/A 792M—01a Specification for Steel Sheet, 55% Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
A 875M—99a Specification for Steel Sheet Zinc-54% Aluminum Alloy-Coated by the Hot Dip Process
A 884—99 Specification for Epoxy-Coated Steel Wire and Welded Wire Fabric for Reinforcement
A 898/A 898M—91 (2001) Specification for Straight Beam Ultrasonic Examination of Rolled Steel Shapes
A 899—91 (1999) S Specification for Steel Wire Epoxy-Coated
A 913/A 913M—01 Specification for High-strength Low-Alloy Steel Shapes of Structural Quality, Produced by Quenching and Self-tempering Process
   (QST)
A 951—00 Specification for Masonry Joint Reinforcement
A 996/A 996M—00 Specification for Rail-Steel and Axle-Steel Deformed Bars Reinforcement for Concrete
A1008—01A Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High-Strength Low-Alloy with
   Improved Formability
B 42—98 Specification for Seamless Copper Pipe, Standard Sizes
B 43—98 Specification for Seamless Red Brass Pipe, Standard Sizes
B 68M—99 Specification for Seamless Copper Tube, Bright Annealed (Metric)
B 88—99el Specification for Seamless Copper Water Tube
B 101—01 Specification for Lead-Coated Copper Sheet and Strip for Building Construction
B 209—96 Specification for Aluminum and Aluminum Alloy Steel and Plate
B 251—97 Specification for General Requirements for Wrought Seamless Copper and Copper-alloy Tube
B 280—99el Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service
B 633—98 Specification for Electrodeposited Coatings of Zinc on Iron and Steel
C 5—97 Specification for Quicklime for Structural Purposes
C 22/C 22M—00 Specification for Gypsum
C 27—98 Specification for Standard Classification of Fireclay and High-Alumina Refractory Brick
C 31/31M—98 Practice for Making and Curing Concrete Test Specimens in the Field
C 33—99ae1 Specification for Concrete Aggregates
C 33—01a Specification for Concrete Aggregates
C 34—96 (2001) Specification for Structural Clay Load-bearing Wall Tile
C 35—95 (2001) Specification for Inorganic Aggregates for Use in Gypsum Plaster
C 36/C 36M-01 Specification for Gypsum Wallboard
C 37/C 37M-01 Specification for Gypsum Lath
C 39—99ae1 Test Method for Compressive Strength of Cylindrical Concrete Specimens
C 42/C 42M—99 est Method for Obtaining and Testing Drilled Cores and Sawed Beams of Concrete
C 55—01A Specification for Concrete Brick
C 56—96 (2001) Specification for Structural Clay Non-load Bearing Tile
C 59/C 59M—00 Specification for Gypsum Casting and Molding Plaster.
C 61/C 61M—00 Specification for Gypsum Keene’s Cement
C 62—01 Specification for Building Brick (Solid Masonry Units Made from Clay or Shale)
C 67—02 Test Methods of Sampling and Testing Brick and Structural Clay Tile
C 73—99a Specification for Calcium Silicate Face Brick (Sand-lime Brick)
C 79—01 Specification for Treated Core and Non-treated Core Gypsum Sheathing Board
C 90—01A Specification for Loadbearing Concrete Masonry Units
C 91—01 Specification for Masonry Cement
C 94/C 94M—00 Specification for Ready-Mixed Concrete
C 126—99 Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units
C 140—01 ae1 Test Method Sampling and Testing Concrete Masonry Units and Related Units
C 150—99a Specification for Portland Cement
C 150—01 Specification for Portland Cement
C 172—99 Practice for Sampling Freshly Mixed Concrete
C 199—84 (2000) Test Method for Pier Test for Refractory Mortars
C 206—84 (1997) Specification for Finishing Hydrated Lime
C 207—97 Specification for Hydrated Lime for Masonry Purposes
C 208—95 Specification for Cellulosic Fiber Insulating Board
C 212—00 Specification for Structural Clay Facing Tile
C 216—01A Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)
C 270—01A Specification for Mortar for Unit Masonry
C 315—00 Specification for Clay Flue Linings
C 317/C 317M—00 Specification for Gypsum Concrete
C 330—99 Specification for Lightweight Aggregates for Structural Concrete
C 331—01 Specification for Lightweight Aggregates for Concrete Masonry Units
C 406—00 Specification for Roofing Slate
C 442/C 442M—01 Specification for Gypsum Backing Board and Coreboard and Gypsum Shaftliner Board
C 472—99 Specification for Standard Test Methods for Physical Testing of Gypsum, Gypsum Plasters and Gypsum Concrete
C 473—00 Test Method for Physical Testing of Gypsum Panel Products
C 474—01 Test Methods for Joint Treatment Materials for Gypsum Board Construction
C 475—01 Specification for Joint Compound and Joint Tape for Finishing Gypsum Wallboard
C 476—01 Specification for Grout for Masonry
C 503—99e01 Specification for Marble Dimension Stone (Exterior)
C 514—01 Specification for Nails for the Application of Gypsum Board
C 516—E01 Specifications for Vermiculite Loose Fill Thermal Insulation.
C 547—00 Specification for Mineral Fiber Pipe Insulation
C 549—81 (1995) Specification for Perlite Loose Fill Insulation
C 557—99 Specification for Adhesives for Fastening Gypsum Wallboard to Wood Framing
C 568—99 Specification for Limestone Dimension Stone
C 587—97 Specification for Gypsum Veneer Plaster
C 588/C 588M—01 Specification for Gypsum Base for Veneer Plasters
C 595—00 Specification for Blended Hydraulic Cements
C 595—01 Specification for Blended Hydraulic Cements
C 615—99 Specification for Granite Dimension Stone
C 616—99 Specification for Quartz-based Dimension Stone
C 618—99 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use as a Mineral Admixture in Concrete
C 629—99 Specification for Slate Dimension Stone
C 630/C 630M—01 Specification for Water-resistant Gypsum Backing Board
C 631—00 Specification for Bonding Compounds for Interior Gypsum Plastering
C 635—00* Specification for the Manufacturer, Performance, and Testing of Metal Suspension Systems for Acoustical Tile and Lay-in Panel
   Ceilings
C 636—96* Practice for Installation of Metal Ceiling Suspension Systems for Acoustical Tile and Lay-in Panels
C 645—00 Specification for Nonstructural Steel Framing Members
C 652—01A Specification for Hollow Brick (Hollow Masonry Units Made from Clay or Shale)
C 685/ C 685M—98a Specification for Concrete Made by Volumetric Batching and Continuous Mixing
C 744—99 Specification for Prefaced Concrete and Calcium Silicate Masonry Units
C 754—00 Specification for Installation of Steel Framing Members to Receive Screw-attached Gypsum Panel Products
C 836—00 Specification for High-solids Content, Cold Liquid-applied Elastomeric Waterproofing Membrane for Use with Separate Wearing
   Course
C 840—01 Specification for Application and Finishing of Gypsum Board
C 841—99 Specification for Installation of Interior Lathing and Furring
C 842—99 Specification for Application of Interior Gypsum Plaster
C 843—99 Specification for Application of Gypsum Veneer Plaster
C 844—99 Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster
C 845—96 Specification for Expansive Hydraulic Cement
C 847—00 Specification for Metal Lath
C 887—(2001) Specification for Packaged, Dry Combined Materials for Surface Bonding Mortar
C 897—00 Specification for Aggregate for Job-Mixed Portland Cement-Based Plasters
C 926—98a Specification for Application of Portland Cement Based-Plaster
C 931/C 931M—01 Specification for Exterior Gypsum Soffit Board
C 932—98a Specification for Surface-applied Bonding Agents for Exterior Plastering
C 933—A(2001) Specification for Welded Wire Lath
C 946—91 (2001) Specification for Practice for Construction of Dry-stacked, Surface-bonded Walls
C 954—00 Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033,
   inch (0.84 mm) to 0.112 inch (2.84 mm) in Thickness
C 955—01 Specification for Load Bearing Transverse and Axial Steel Studs, Runners Tracks, and Bracing or Bridging, for Screw Application of    Gypsum Panel Products and Metal Plaster Bases
C 956—97 Specification for Installation of Cast-in-place Reinforced Gypsum Concrete
C 957—98 Specification for High-solids Content, Cold Liquid-applied Elastomeric Waterproofing Membrane with Integral Wearing Surface
C 960—97 Specification for Predecorated Gypsum Board
C 989—99 Specification for Ground Granulated Blast-furnace Slag for Use in Concrete and Mortars
C1002—01 Specification for Steel Self-Piercing Tapping Screws for the Application
   of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs
C1007—00 Specification for Installation of Load Bearing (Transverse and Axial) Steel Studs and Related Accessories
C1019—00B Test Method of Sampling and Testing Grout
C1029—96 Specification for Spray-applied Rigid Cellular Polyurethane Thermal Insulation
C1032—96 Specification for Woven Wire Plaster Base
C1047—99 Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base
C1063—99 Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement Based Plaster
C1088—01A Specification for Thin Veneer Brick Units Made from Clay or Shale
C1157—00 Performance Specification for Hydraulic Cement
C1167—96 Specification for Clay Roof Tiles
C1177/C1177M—01 Specification for Glass Mat Gypsum Substrate for Use as Sheathing
C1178/C1178M—01 Specification for Glass Mat Water-resistant Gypsum Backing Panel
C1186—99 Specification for Flat Nonasbestos Fiber Cement Sheets
C1218/ C1218M—99 Test Method for Water-soluble Chloride in Mortar and Concrete
C1240—00E1 Specification for Silica Fume for Use as a Mineral Admixture in Hydraulic-Cement Concrete, Mortar and Grout
C1261—98 Specification for Firebox Brick for Residential Fireplaces
C1278/C 1278M—01 Specification for Fiber-reinforced Gypsum Panels
C1280—99 Specification for Application of Gypsum Sheathing
C1283—00 Practice for Installing Clay Flue Liners
C1314—02 Test Method for Compressive Strength of Masonry Prisms
C1328—00 Specification for Plastic (Stucco Cement)
C1329—00 Specification for Mortar Cement
**C1371—04a (2010)el Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
C1395/1395M—01 Specification for Gypsum Ceiling Board
**C1549—(2009) Standard Test Method for Determination of Solar Reflectance Near Ambient Temperature Using a Portable Solar Reflectometer
D 25—99E01 Specification for Round Timber Piles
D 41—E01 Specification for Asphalt Primer Used in Roofing, Dampproofing and Waterproofing
D 43—00 Coal Tar Primer Used in Roofing, Dampproofing and Waterproofing
D 56—01 Test Method for Flash Point By Tag Closed Tester
D 86—01e01 Test Method for Distillation of Petroleum Products
D 93—00 Test Method for Flash Point By Pensky-Martens Closed Cup Tester
D 224—89 (1996) Specification for Smooth-Surfaced Asphalt Roll Roofing (Organic Felt)
D 225—01 Specification for Asphalt Shingles (Organic Felt) Surfaced with Mineral Granules
D 226—97a Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing
D 227—97a Specification for Coal-tar-saturated Organic Felt Used in Roofing and Waterproofing
D 249—89 (1996) Specification for Asphalt Roll Roofing (Organic Felt) Surfaced with Mineral Granules
D 312—00 Specification for Asphalt Used in Roofing
D 371—89 (1996) Specification for Asphalt Roll Roofing (Organic Felt) Surfaced with Mineral Granules: Wide-selvage
D 422—98 Test Method for Particle-size Analysis of Soils
D 450—00 Specification for Coal-tar Pitch Used in Roofing, Dampproofing and Waterproofing
D 635—98 Test Method for Rate of Burning and/or Extent and Time of Burning of Self-Supporting Plastics in a Horizontal Position
***D 692 / D692M—99 Standard Specification for Coarse Aggregate for Bituminous Paving Mixtures Standard
***D1073—07 Specification for Fine Aggregate for Bituminous Paving Mixtures
D1143—81 (1994) E01 Test Method for Piles Under Static Axial Compressive Load
D1227—00 Specification for Emulsified Asphalt Used as a Protective Coating for Roofing
D1557—00 Test Method for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lb/ft3 (2,700 KN m/m3))
D1586—99 Specification for Penetration Test and Split-barrel Sampling of Soils
D1761—88(2000) Test Method for Mechanical Fasteners in Wood
D1863—93 (2000) Specification for Mineral Aggregate Used on Built-up Roofs
D1929—96 (2001)E01 Test Method for Determining Ignition Properties of Plastics
D1970—01 Specification for Self-Adhering Polymer Modified Bituminous Sheet Materials Used as Steep Roof Underlayment for Ice Dam
   Protection
D2166—00 Test Method for Unconfined Compressive Strength of Cohesive Soil
D2178—97a Specification for Asphalt Glass Felt Used in Roofing and Waterproofing
D2216—98 Test Method for Laboratory Determination of Water(Moisture) Content of Soil and Rock by Mass
D2487—00 Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
D2626—97b Specification for Asphalt Saturated and Coated Organic Felt Base Sheet Used in Roofing
D2822—91(97) el Specification for Asphalt Roof Cement
D2823—90(97) el Specification for Asphalt Roof Coatings
D2843—99 Test for Density of Smoke from the Burning or Decomposition of Plastics
D2850—95(1999) Test Method for Unconsolidated, Undrained Triaxial Compression Test on Cohesive Soils
D2898—94 (1999) Test Methods for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing
D3019—e01(Supp) Specification for Lap Cement Used with Asphalt Roll Roofing, Nonfibered, Asbestos Fibered, and Nonasbestos Fibered
D3161—99a Test Method for a Wind Resistance of Asphalt Shingles (Fan Induced Method)
D3201—94 (1998) el Test Method for Hygroscopic Properties of Fire-Retardant Treated Wood and Wood-base Products
D3278—96e01 Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
D3462—E01 Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules
D3468—99 Specification for Liquid-applied Neoprene and Chlorosulfonated Polyethylene Used in Roofing and Waterproofing
D3679—01c(Supp) Specification for Rigid Poly [Vinyl Chloride (PVC) Siding]
D3689—90 (1995) Method for Testing Individual Piles Under Static Axial Tensile Load
D3737—01B Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)
D3746—85 (1996) el Test Method for Impact Resistance of Bituminous Roofing Systems
D3747—E01 Specification for Emulsified Asphalt Adhesive for Adhering Roof Insulation
D3909—97b Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules
D4022—00 Specification for Coal Tar Roof Cement, Asbestos Containing
D4272—99 Test Method for Total Energy Impact of Plastic Films by Dart Drop
D4318—00 Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soil
D4434—96 Specification for Poly (Vinyl Chloride) Sheet Roofing
D4479—00 Specification for Asphalt Roof Coatings -Asbestos-Free
D4586—00 Specification for Asphalt Roof Cement, Asbestos-Free
D4601—98 Specification for Asphalt-Coated Glass Fiber Base Sheet Used in Roofing
D4637—96 Specification for EPDM Sheet Used in Single-ply Roof Membrane
D4829—95 Test Method for Expansion Index of Soils
D4869—93 Specification for Asphalt-Saturated (Organic Felt) Underlayment Used in Steep Slope Roofing
D4897—01 Specification for Asphalt-Coated Glass Fiber Venting Base Sheet Used in Roofing
D4990—97a Specification for Coal Tar Glass Felt Used in Roofing and Waterproofing
D4945—00 Test Method for High-Strain Dynamic Testing of Piles P
D5019—96 Specification for Reinforced Nonvulcanized Polymeric Sheet Used in Roofing Membrane
D5055—00 Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-joists
D5456—01AE01 Specification for Evaluation of Structural Composite Lumber Products
D5516—99a Test Method of Evaluating the Flexural Properties of Fire-Retardant Treated Softwood Plywood Exposed to the
   Elevated Temperatures
D5643—00 Specification for Coal Tar Roof Cement, Asbestos-Free
D5664—01 Test Methods for Evaluating the Effects of Fire-Retardant Treatment and Elevated Temperatures on Strength Properties of Fire-
   Retardant Treated Lumber
D5665—99a Specification for Thermoplastic Fabrics Used in Cold-Applied Roofing and Waterproofing
D5726—98 Specification for Thermoplastic Fabrics Used in Hot-Applied Roofing and Waterproofing
D6083—97a Specification for Liquid Applied Acrylic Coating Used in Roofing
D6162—00A Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and
   Glass Fiber Reinforcements
D6163—00 E01 Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements
D6164—00 Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Metal Materials Using Polyester Reinforcements
D6222—98 Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements
D6223—98 Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass
   Fiber Reinforcements
D6298—98 Specification for Fiberglass Reinforced Styrene-Butadiene-Styrene (SBS) Modified Bituminous Sheets with a Factory Applied
   Metal Surface
D6305—99e1 Practice for Calculating Bending Strength Design Adjustment Factors for Fire-Retardant-Treated Plywood Roof Sheathing
E 84—01 Test Methods for Surface Burning Characteristics of Building Material
E 90—99 Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements
E 96—00 Test Method for Water Vapor Transmission of Materials
E 108—00 Test Methods for Fire Tests of Roof Coverings
E 119—00 Test Methods for Fire Tests of Building Construction and Materials
E 136—99 Test Method for Behavior of Materials in a Vertical Tube Furnace at 750°C
E 328—86 Methods for Stress Relaxation for Materials and Structures
E 330—97 Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference
E 331—00 Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure
   Difference
E 336—05 Standard Test Method for Measurement of Airborne Sound Insulation in Buildings
**E408—71 (2008) Standard Test Methods for Total Normal Emittance of Surfaces Using Inspection-Meter Techniques
E 492—90 (1996)e1 Test Method for Laboratory Measurement of Impact Sound Transmission Through Floor-ceiling Assemblies Using the Tapping
   Machine
E 605—00 Test Method for Thickness and Density of Sprayed Fire-resistive Material (SFRM) Applied to Structural Members
E 681—01 Test Methods for Concentration Limits of Flammability of Chemical Vapors and Gases
E 736—00 Test Method for Cohesion/Adhesion of Sprayed Fire-resistive Materials Applied to Structural Members
E 814—00 Test Method of Fire Tests of Through-penetration Firestops
E 970—00 Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source
E1007—97 Test Method for Field Measurement of Tapping Machine Impact Sound Transmission through Floor-Ceiling Assemblies and
   Associated Support Structures
E1300—00 Practice for Determining Load Resistance of Glass in Buildings
E1592—01 Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference
E1602—01 Guide for Construction of Solid Fuel-Burning Masonry Heaters
E1886—97 Test Method for Performance of Exterior Windows, Curtain Wall, Doors and Storm Shutters Impacted by Missiles and exposed to
   Cyclic Pressure Differentials
**E1918 (2006) Standard Test Method for Measuring Solar Reflectance of Horizontal and Low-Sloped Surfaces in the Field
E1966—00 Test Method for Fire-Resistant Joint Systems
**E1980 (2011) Standard Practice for Calculating Solar Reflectance Index of Horizontal and Low-Sloped Opaque Surfaces
E1996—01 Specification for Performance of Exterior Windows, Glazed Curtain Walls, Doors and Storm Shutters Impacted by Windborne
   Debris in Hurricanes
F 547—01 Terminology of Nails for Use with Wood and Wood-base Materials
F1346—91 (1996) Performance Specification for Safety Covers and Labeling Requirements for All Covers for Swimming Pools, Spas and Hot Tubs
F1667—01A Specification for Driven Fasteners: Nails, Spikes, and Staples
G 152—00A Practice for Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials
G 154—00A Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials
G 155—00A Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials
* As modified in Appendix R, where applicable pursuant to Section 803.9
AWPA American Wood-Preservers’ Association
P.O. Box 5690
Grandbury, TX 76049
Standard
Reference
Number
Title
C1—00 All Timber Products—Preservative Treatment by Pressure Processes
C2—01 Lumber, Timber, Bridge Ties and Mine Ties—Preservative Treatment by Pressure Processes
C3—99 Piles—Preservative Treatment by Pressure Processes
C4—99 Poles—Preservative Treatment by Pressure Processes
C9—00 Plywood—Preservative Treatment by Pressure Processes
C14—99 Wood for Highway Construction, Pressure Treatment by Pressure Process
C15—00 Wood for Commercial-Residential Construction Preservative Treatment by Pressure Process
C16—00 Wood Used on Farms, Pressure Treatment by Pressure Process
C18—99 Standard for Pressure Treated Material in Marine Construction
C22—96 Lumber and Plywood for Permanent Wood Foundations—Preservative Treatment by Pressure Processes
C23—00 Round Poles and Posts Used in Building Construction—Preservative Treatment by Pressure Processes
C24—96 Sawn Timber Piles Used to Support Residential and Commercial Structures
C28—99 Standard for Preservative Treatment by Pressure Process of Structural Glued Laminated Members and Laminations before Gluing
C31—00 Lumber Used Out of Contact with the Ground and Continuously Protected from Liquid Water—Treatment by Pressure Processes
C33—00 Standard for Preservative Treatment of Structural Composite Lumber by Pressure Processes
M4—01 Standard for the Care of Preservative-Treated Wood Products
P1/13—01 Standard for Creosote Preservative
P2—01 Standard for Creosote Solutions
P5—01 Standard for Waterborne Preservatives
P8—01 Standard for Oil-borne Preservatives
P9—01 Standard for Solvents and Formulations for Organic Preservative Systems
AWS American Welding Society
550 N.W. LeJeune Road
Miami, FL 33126
Standard
Reference
Number
Title
D1.1—00 Structural Welding Code—Steel
D1.3—98 Structural Welding Code—Sheet Steel
D1.4—98 Structural Welding Code—Reinforcing Steel
BHMA Builders Hardware Manufacturers’ Association
355 Lexington Avenue, 17th Floor
New York, NY 10017-6603
Standard
Reference
Number
Title
A 156.10—99 American National Standard for Power Operated Pedestrian Doors
A 156.19—97 American National Standard for Power Assist and Low Energy Operated Doors
CGSB Canadian General Standards Board
222 Queens Street
14th Floor, Suite 1402
Ottawa, Ontario, Canada KIA 1G6
Standard
Reference
Number
Title
37-GP-52M (1984) Roofing and Waterproofing Membrane, Sheet Applied, Elastomeric CAN/CGSB
37.54—95 Polyvinyl Chloride Roofing and Waterproofing Membrane.
37-GP-56M (1980) Membrane, Modified, Bituminous, Prefabricated, and Reinforced for Roofing—with December 1985 Amendment
CPSC Consumer Product Safety Commission
4330 East West Highway
Bethesada, MD 20814-4408
Standard
Reference
Number
Title
16 CFR Part 1201(1977) Safety Standard for Architectural Glazing Material
16 CFR Part 1209(1979) Interim Safety Standard for Cellulose Insulation
16 CFR Part 1404 (1979) Cellulose Insulation
16 CFR Part 1500 (1991) Hazardous Substances and Articles; Administration and Enforcement Regulations
16 CFR Part 1500.44 (2001) Method for Determining Extremely Flammable and Flammable Solids
16 CFR Part 1507 (2001) Fireworks Devices
16 CFR Part 1630 (2000) Standard for the Surface Flammability of Carpets and Rugs
CSSB Cedar Shake and Shingle Bureau
P.O. Box 1178
Sumas, WA 98295-1178
Standard
Reference
Number
Title
CSSB—97 Grading and Packing Rules for Western Red Cedar Shakes and Western Red Shingles of the Cedar Shake and Shingle Bureau
DASMA Door and Access Systems Manufacturers
Association International
1300 Summer Avenue
Cleveland, OH 44115-2851
Standard
Reference
Number
Title
107—97 Room Fire Test Standard for Garage Doors Using Foam Plastic Insulation
DOC U.S. Department of Commerce
National Institute of Standards and Technology
100 Bureau Drive Stop 3460
Gaithersburg, MD 20899
Standard
Reference
Number
Title
PS-1—95 Construction and Industrial Plywood
PS-2—92 Performance Standard for Wood-based Structural-use Panels
PS 20—99 American Softwood Lumber Standard
DOL U.S. Department of Labor
c/o Superintendent of Documents
U.S. Government Printing Office
Washington, DC 20402-9325
Standard
Reference
Number
Title
29 CFR Part 1910.1000 (1974) Air Contaminants
DOTn U.S. Department of Transportation
c/o Superintendent of Documents
U.S. Government Printing Office
Washington, DC 20402-9325
Standard
Reference
Number
Title
49 CFR Part 172 (1999) Hazardous Materials Tables, Special Provisions, Hazardous Materials Communications, Emergency Response Information and Training    Requirements
49 CFR Parts 173 (1999) Specification of Transportation of Explosive and Other Dangerous Articles, UN 0335, UN 0336 Shipping Containers
FEMA Federal Emergency Management Agency
Federal Center Plaza
500 C Street S.W.Washington, DC 20472
Standard
Reference
Number
Title
Pub 302 NEHRP Recommended Provisions for Seismic Regulations for New Buildings and Other Structures
FM Factory Mutual
Standards Laboratories Department
1151 Boston-Providence Turnpike
Norwood, MA 02062
Standard
Reference
Number
Title
4450 (1989) Approval Standard for Class 1 Insulated Steel Deck Roofs—with Supplements thru 7/92
4470 (1992) Approval Standard for Class 1 Roof Covers
4880 (2001) American National Standard for Evaluating Insulated Wall or Wall and Roof/Ceiling Assemblies, Plastic Interior Finish Materials,
   Plastic Exterior Building Panels, Wall/Ceiling Coating Systems, Interior and Exterior Finish Systems.
GA Gypsum Association
810 First Street N.E. #510
Washington, DC 20002-4268
Standard
Reference
Number
Title
GA 216—00 Application and Finishing of Gypsum Board
GA 600—00 Fire-resistance Design Manual,16th Edition, April, 2000
HPVA Hardwood Plywood Veneer Association
1825 Michael Faraday Drive
Reston, VA 20190-5350
Standard
Reference
Number
Title
HP-1—2000 The American National Standard for Hardwood and Decorative Plywood
ICC International Code Council
5203 Leesburg Pike, Suite 600
Falls Church, VA 22041
Standard
Reference
Number
Title
ICC/ANSI A117.1—2003 Accessible and Usable Buildings and Facilities
ICC 300—02 ICC Standard on Bleachers, Folding and Telescopic Seating, and Grandstands
SBCCI SSTD 10—99 Standard for Hurricane Resistant Residential Construction
SBCCI SSTD 11—97 Test Standard for Determining Wind Resistance of Concrete or Clay Roof Tiles UBC Standard 18-2 Expansion Index Test
NAAMM National Association of Architectural
Metal Manufacturers
8 South Michigan Ave
Chicago, IL 60603
Standard
Reference
Number
Title
FP 1001—90 Guide Specifications for Design of Metal Flag Poles
NCMA National Concrete Masonry Association
2302 Horse Pen Road
Herndon, VA 22071-3499
Standard
Reference
Number
Title
TEK 5-8A (1996) Details for Concrete Masonry Fire Walls
NFPA National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02269-9101
Standard
Reference
Number
Title
13—02* Installation of Sprinkler Systems
13D—02* Installation of Sprinkler Systems in One-and Two-family Dwellings and Manufactured Homes
13R—02* Installation of Sprinkler Systems in Residential Occupancies Up to and Including Four Stories in Height
14—03* Installation of Standpipe, Private Hydrants and Hose System
30—00 Flammable and Combustible Liquids Code
32—00 Dry-cleaning Plants
**40—01 Storage and Handling of Cellulose Nitrate Film
**45—04 Standard on Fire Protection for Laboratories Using Chemicals
61—99 Prevention of Fires and Dust Explosions in Agricultural and Food Product Facilities
72—2002* National Fire Alarm Code
80—99 Fire Doors and Fire Windows
85—01 Boiler and Combustion System Hazards Code (Note: NFPA 8503 has been incorporated into NFPA 85)
99—05 Standard for Health Care Facilities
99c—05 Standard on Gas and Vacuum Systems
101—00 Life Safety Code
110—99 Emergency and Standby Power Systems
111—01 Stored Electrical Energy Emergency and Standby Power Systems
120—99 Coal Preparation Plants
252—99 Standard Methods of Fire Tests of Door Assemblies
253—00 Test for Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat Energy Source
257—00 Standard for Fire Test for Window and Glass Block Assemblies
259—98 Test Method for Potential Heat of Building Materials
265—98 Standard Method of Fire Tests for Evaluating Room Fire Growth Contribution of Textile Wall Coverings
268—96 Standard Test Method for Determining Ignitibility of Exterior Wall Assemblies Using a Radiant Heat Energy Source
285—98 Standard Method of Test for the Evaluation of Flammability Characteristics of Exterior Non-load-bearing Wall Assemblies
   Containing Combustible Components
286—00 Standard Method of Fire Test for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth
409—95 Standard on Aircraft Hangers
418—01 Standard for Heliports
651—98 Machining and Finishing of Aluminum and the Production and Handling of Aluminum Powders
654—00 Prevention of Fire & Dust Explosions from the Manufacturing, Processing, and Handling of Combustible Particulate Solids
655—93 Prevention of Sulfur Fires and Explosions
664—98 Prevention of Fires Explosions in Wood Processing and Woodworking Facilities
701—99 Standard Methods of Fire Tests for Flame-Propagation of Textiles and Films
704—96 Standard System for the Identification of the Hazards of Materials for Emergency Response
1124—98 Manufacture, Transportation, and Storage of Fireworks and Pyrotechnic Articles
* As modified in Appendix Q
NYC/NYC New York City Codes / New York State Codes / NYC Agencies
Standard
Reference
Number
Title
Energy Conservation Construction Code of New York
State
New York City Air Pollution Control Code
New York City Department of Consumer Affairs
New York City Department of Environmental
Protection
New York City Department of Health and Mental
Hygiene
New York City Department of Housing Preservation
and Development
New York City Department of Records and
Information Services
New York City Department of Transportation
New York City Electrical Code based on 2005 NEC
New York City Fire Code
New York City Fire Department
   New York City Fuel Gas Code based on 2003 IFGC
New York City Housing Maintenance Code
New York City Mechanical Code based on 2003 IMC
New York City Plumbing Code based on 2003 IPC
New York State Health Code
NIST National Institute of Standards and Technology
U.S. Department of Commerce
100 Bureau Dr. –Stop 3460
Gaithersburg, MD 20899-3460
Standard
Reference
Number
Title
BMS 71—41 Fire Tests of Wood and Metal-framed Partitions
TRBM-44—46 Fire-resistance and Sound-insulation Ratings for Walls, Partitions and Floors
PCI Precast Prestressed Concrete Institute
175 W. Jackson Boulevard, Suite 1859
Chicago, IL 60604-9773
Standard
Reference
Number
Title
MNL 124—89 Design for Fire Resistance of Precast Prestressed Concrete
MNL 128—01 Recommended Practice for Glass Fiber Reinforced Concrete Panels
PTI Post-Tensioning Institute
1717 W. Northern Avenue, Suite 114
Phoenix, AZ 85021
Standard
Reference
Number
Title
PTI 1996 Design and Construction of Post-tensioned Slabs-on-ground, 2nd Edition
RMA Rubber Manufacturers Association
1400 K. Street, N.W. #900
Washington, DC 20005
Standard
Reference
Number
Title
RP-1—90 Minimum Requirements for Non-reinforced Black EPDM Rubber Sheets
RP-2—90 Minimum Requirements for Fabric-reinforced Black EPDM Rubber Sheets
RP-3—85 Minimum Requirements for Fabric-reinforced Black Polychloroprene Rubber Sheets
RMI Rack Manufacturers Institute
8720 Red Oak Boulevard, Suite 201
Charlotte, NC 28217
Standard
Reference
Number
Title
RMI (1997) Design, Testing and Utilization of Industrial Steel Storage Racks
SJI Steel Joist Institute
3127 10th Avenue, North
Myrtle Beach, SC 29577-6760
Standard
Reference
Number
Title
SJI—1994 Standard Specification for Joist Girders
K-Series Specification
—1994
Standard Specification for Open Web Steel Joists, K Series.
SJI—1994 Standard Specification for Longspan Steel Joists, LH Series and Deep Longspan Steel Joists, DLH Series
SPRI Single-Ply Roofing Institute
77 Rumford Ave.
Suite 3-B
Walthem, MA 02453
Standard
Reference
Number
Title
ES-1—98 Wind Design Standard for Edge Systems Used with Low Slope Roofing Systems
RP-4—88 Wind Design Guide for Ballasted Single-ply Roofing Systems
TIA Telecommunications Industry Association
2500 Wilson Boulevard
Arlington, VA 22201-3834
Standard
Reference
Number
Title
TIA/EIA-222-F—96 Structural Standards for Steel Antenna Towers and Antenna Supporting Structures
TMS The Masonry Society
3970 Broadway, Unit 201-D
Boulder, CO 80304-1135
Standard
Reference
Number
Title
0216—97 Standard Method for Determining Fire Resistance of Concrete and Masonry Construction Assemblies
402—02 Building Code Requirements for Masonry Structures
602—02 Specification for Masonry Structures
TPI Truss Plate Institute
583 D’Onofrio Drive, Suite 200
Madison, WI 53719
Standard
Reference
Number
Title
TPI 1—2002 National Design Standards for Metal-Plate-Connected Wood Truss Construction
UL Underwriters Laboratories
333 Pfingsten Road
Northbrook, IL 60062-2096
Standard
Reference
Number
Title
10A—98 Tin Clad Fire Doors—with Revisions through July, 1998
10B—97 Fire Tests of Door Assemblies
10C—98 Positive Pressure Fire Tests of Door Assemblies—with Revisions thru November, 2001
14B—98 Sliding Hardware for Standard Horizontally Mounted Tin Clad Fire Doors—with Revisions through July, 2000
14C—96 Swinging Hardware for Standard Tin Clad Fire Doors Mounted Singly and in Pairs
103—98 Factory-Built Chimneys, for Residential Type and Building Heating Appliances—with Revisions through March 1999
127—99 Factory-Built Fireplaces—with Revisions through November, 1999
****217—09 Standard for Single and Multiple Station Smoke Alarms.
268—96 Smoke Detectors for Fire Protective Signaling Systems—with Revisions through January, 1999
300—96 Fire Testing of Fire Extinguishing Systems for Protection of Restaurant Cooking Areas —with Revisions through December, 1998
555—96 Fire Dampers—with Revisions through October, 2000
555C—96 Ceiling Dampers
555S—99 Smoke Dampers—with Revisions through December, 1999
580—94 Test for Uplift Resistance of Roof Assemblies—with Revisions through February, 1998
641—95 Type L Low-Temperature Venting Systems—with Revisions through April, 1999
790—97 Tests for Fire Resistance of Roof Covering Materials—with Revisions through July, 1998
864—96 Control Units for Fire Protective Signaling Systems—with Revisions through March, 1999
1040—96 Fire Test of Insulated Wall Construction—with Revisions thru April, 2001
1256—98 Fire Test of Roof Deck Construction—with Revisions through March, 2000
1479—94 Fire Tests of Through-Penetration Firestops
1715—97 Fire Test of Interior Finish Material
1777—98 Chimney Liners—with Revisions through July, 1998
1784—95 Air Leakage Tests of Door Assemblies
1897—98 Uplift Tests for Roof Covering Systems—with Revisions through December, 1999
1975—96 Fire Test of Foamed Plastics Used for Decorative Purposes
**2034—08 Standard for Single and Multiple Station Carbon Monoxide Alarms
2075—04, revised 7/20/05 Standard for Gas and Vapor Detectors and Sensors
2079—98 Tests for Fire Resistance of Building Joint Systems
2200—98 Stationary Engine Generator Assemblies
ULC Underwriters Laboratories of Canada
7 Crouse Road
Scarborough, Ontario, Canada M1R3A9
Standard
Reference
Number
Title
S102.2—M88 Standard Method of Test for Surface Burning Characteristics of Floor Coverings, and Miscellaneous Materials and Assemblies
USC United States Code
c/o Superintendent of Documents
U.S. Government Printing Office
Washington, DC 20402-9325
Standard
Reference
Number
Title
18 USC Part 1, Ch.40 Importation, Manufacture, Distribution and Storage of Explosive Materials
WDMA Window and Door Manufacturers Association
1400 East Touhy Avenue #470
Des Plaines, IL 60018
Standard
Reference
Number
Title
AAMA/NWWDA
101/I.S.2—97
Voluntary Specifications for Aluminum, Vinyl (PVC) and Wood Windows and Glass Doors
AAMA/NWWDA
101/I.S.2/NAFS—02
Voluntary Performance Specification for Window, Skylights and Glass Doors
WRI Wire Reinforcement Institute, Inc.
203 Loudon Street, S.W.
2nd Floor, Suite 203
CLeesburg, VA 22075
Standard
Reference
Number
Title
WRI/CRSI—96 Design of Slab-on-ground Foundations
Resources