MINIMUM SPECIFIED COMPRESSIVE STRENGTH (f 'c)
|TYPE OR LOCATION OF CONCRETE CONSTRUCTION||MINIMUM SPECIFIED COMPRESSIVE STRENGTH (f 'c at 28 days, psi)|
|Negligible exposure||Moderate exposure||Severe exposure|
|Basement wallsc and foundations not exposed to the weather||2,500||2,500||2,500a|
|Basement slabs and interior slabs on grade, except garage floor slabs||2,500||2,500||2,500a|
|Basement wallsc, foundation walls, exterior walls and other vertical concrete surfaces exposed to the weather||2,500||3,000b||3,000b|
|Driveways, curbs, walks, patios, porches, carport slabs, steps and other flatwork exposed to the weather, and garage floor slabs||2,500||3,000b, d||3,500b, d|
WEATHERING PROBABILITY MAP FOR CONCRETEa, b, c
220.127.116.11 - Structures assigned to Seismic Design Category A shall satisfy requirements of Chapters 1 to 19 and 22; Chapter 21 does not apply. Structures assigned to Seismic Design Category B, C, D, E or F also shall satisfy 18.104.22.168 through 22.214.171.124, as applicable. Except for structural elements of plain concrete complying with Section 1905.1.8 of the International Building Code, structural elements of plain concrete are prohibited in structures assigned to Seismic Design Category C, D, E or F.
126.96.36.199 - Structural systems designated as part of the seismic force-resisting system shall be restricted to those permitted by ASCE 7. Except for Seismic Design Category A, for which Chapter 21 does not apply, the following provisions shall be satisfied for each structural system designated as part of the seismic force-resisting system, regardless of the Seismic Design Category:
All special moment frames and special structural walls shall also satisfy 21.1.3 through 21.1.7.
21.4.3 - Connections that are designed to yield shall be capable of maintaining 80 percent of their design strength at the deformation induced by the design displacement or shall use Type 2 mechanical splices.
21.4.4 - Elements of the connection that are not designed to yield shall develop at least 1.5 Sy.
21.4.6 - Wall piers not designed as part of a moment frame in buildings assigned to Seismic Design Category C shall have transverse reinforcement designed to resist the shear forces determined from 21.3.3. Spacing of transverse reinforcement shall not exceed 8 inches (203 mm). Transverse reinforcement shall be extended beyond the pier clear height for at least 12 inches (305 mm).
21.4.7 - Wall segments with a horizontal length-to-thickness ratio less than 2.5 shall be designed as columns.
188.8.131.52 - Wall piers not designed as a part of a special moment frame shall have transverse reinforcement designed to satisfy the requirements in 184.108.40.206.
220.127.116.11 - Transverse reinforcement with seismic hooks at both ends shall be designed to resist the shear forces determined from 18.104.22.168. Spacing of transverse reinforcement shall not exceed 6 inches (152 mm). Transverse reinforcement shall be extended beyond the pier clear height for at least 12 inches (305 mm).
22.214.171.124 - Wall segments with a horizontal length-to-thickness ratio less than 2.5 shall be designed as columns.
126.96.36.199 - Foundations resisting earthquake-induced forces or transferring earthquake-induced forces between a structure and ground shall comply with the requirements of Section 21.12 and other applicable provisions of ACI 318 unless modified by Chapter 18 of the International Building Code.
188.8.131.52 - Reinforcement shall be provided as follows:
Reinforcement at the top and bottom of openings, where used in determining the maximum spacing specified in Item 3 above, shall be continuous in the wall.
Exception: In detached one- and two-family dwellings three stories or less in height, the projection of the footing beyond the face of the supported member is permitted to exceed the footing thickness.
D.3.3.5 - Instead of D.3.3.4, the attachment that the anchor is connecting to the structure shall be designed so that the attachment will undergo ductile yielding at a force level corresponding to anchor forces no greater than the design strength of anchors specified in D.3.3.3.
D.3.3.7 – In light-frame construction, bearing or non-bearing walls, shear strength of concrete anchors less than or equal to 1 inch (25 mm) in diameter of sill plate or track to foundation or foundation stem wall need not satisfy D.3.3.6 when the design strength of the anchors is determined in accordance with D.6.2.1(c).
D.4.2.2 - The concrete breakout strength requirements for anchors in tension shall be considered satisfied by the design procedure of D.5.2 provided Equation D-7 is not used for anchor embedments exceeding 25 inches. The concrete breakout strength requirements for anchors in shear with diameters not exceeding 2 inches shall be considered satisfied by the design procedure of D.6.2. For anchors in shear with diameters exceeding 2 inches, shear anchor reinforcement shall be provided in accordance with the procedures of D.6.2.9.
|(Ps / Pt )5/3 + (Vs/ Vt ) 5/3 ≤ 1||(Equation 19-1)|
|Ps||=||Applied tension service load, pounds (N).|
|Pt||=||Allowable tension service load from Table 1908.2, pounds (N).|
|Vs||=||Applied shear service load, pounds (N).|
|Vt||=||Allowable shear service load from Table 1908.2, pounds (N).|
ALLOWABLE SERVICE LOAD ON EMBEDDED BOLTS (pounds)
|MINIMUM CONCRETE STRENGTH (psi)|
|f 'c = 2,500||f 'c = 3,000||f 'c = 4,000|
Exception: Subject to the approval of the building official, required clearances shall be reduced where it is demonstrated by preconstruction tests that adequate encasement of the bars used in the design will be achieved.