CODES

ADOPTS WITH AMENDMENTS:

International Building Code 2009 (IBC 2009)

This chapter lists the standards that are referenced in various sections of the building code. The standards are listed herein by the promulgating agency of the standard, the standard identification, the effective date and title. The application of the referenced standards shall be as specified in Section 102.5.

When indicated in this code, the following codes refer to provisions in the listed chapters of the administrative code:

REFERENCED CODEOHIO ADMINISTRATIVE CODE CHAPTERS
Building Code4101:1-1 to 4101:1-35
Energy Code4101:1-13
Fire Code1301:7-1 to 1301:7-7
Mechanical Code4101:2-1 to 4101:2-15
Ohio Boiler and Pressure Vessel Rules4101:4-1 to 4101:4-10
Ohio Elevator Code4101:5-1 to 4101:5-3
Residential Code of Ohio for One-, Two- and Three-Family Dwellings4101:8-1 to 4101:8-44
Plumbing Code4101:3-1 to 4101:3-13

AA

Aluminum Association
1525 Wilson Boulevard, Suite 600
Arlington VA 22209
Standard
reference
number
TitleReferenced
in code
section number

ADM1—10

Aluminum Design Manual: Part 1-A Specification for Aluminum Structures, Allowable Stress Design;
and Part 1-B—Aluminum Structures, Load and Resistance Factor Design

ASM 35—00

Aluminum Sheet Metal Work in Building Construction (Fourth Edition)

AAMA

American Architectural Manufacturers Association
1827 Waldon Office Square, Suite 550
Schaumburg IL 60173
Standard
reference
number
TitleReferenced
in code
section number

1402—09

Standard Specifications for Aluminum Siding, Soffit and Fascia

AAMA/WDMA/CSA 101/I.S.2/A440—08

North American Fenestration Standard/Specifications for Windows, Doors and Skylights

ACI

American Concrete Institute
38800 Country Club Drive
Farmington Hills MI 48331
Standard
reference
number
TitleReferenced
in code
section number

216.1—07

Standard Method for Determining Fire Resistance of Concrete and Masonry Construction Assemblies

318—08

Building Code Requirements for Structural Concrete

530—08

Building Code Requirements for Masonry Structures

530.1—08

Specifications for Masonry Structures

AF&PA

American Forest & Paper Association
1111 19th St, NW Suite 800
Washington DC 20036
Standard
reference
number
TitleReferenced
in code
section number

WCD No. 4—03

Wood Construction Data—Plank and Beam Framing for Residential Buildings

NDS—05

National Design Specification (NDS) for Wood Construction with 2005 Supplement

AF&PA—93

Span Tables for Joists and Rafters

ANSI/AF&PA PWF—07

Permanent Wood Foundation Design Specification

ANSI/AF&PA SDPWS—08

Special Design Provisions for Wind and Seismic

AISC

American Institute of Steel Construction
One East Wacker Drive, Suite 700
Chicago IL 60601-18021
Standard
reference
number
TitleReferenced
in code
section number

341—05

Seismic Provisions for Structural Steel Buildings, including Supplement No. 1 dated 2005

360—05

Specification for Structural Steel Buildings

AISI

American Iron and Steel Institute
1140 Connecticut Avenue, 705
Suite 705 DC 20036
Washington
Standard
reference
number
TitleReferenced
in code
section number

S100—07

North American Specification for the Design of Cold-formed Steel Structural Members

S200—08

North American Standard for Cold-formed Steel Framing—General Provisions

S210—08

North American Standard for Cold-formed Steel Framing—Floor and Roof System Design

S211—08

North American Standard for Cold-formed Steel Framing—Wall Stud Design

S212—08

North American Standard for Cold-formed Steel Framing—Header Design

S213—08

North American Standard for Cold-formed Steel Framing—Lateral Design

S214—08

North American Standard for Cold-formed Steel Framing—Truss Design, with Supplement 2, dated 2008

AITC

American Institute of Timber Construction
Suite 140
7012 S. Revere Parkway CO 80112
Englewood
Standard
reference
number
TitleReferenced
in code
section number

AITC Technical
Note 7—96

Calculation of Fire Resistance of Glued Laminated Timbers

AITC 104—03

Typical Construction Details

AITC 110—01

Standard Appearance Grades for Structural Glued Laminated Timber

AITC 113—01

Standard for Dimensions of Structural Glued Laminated Timber

AITC 117—04

Standard Specifications for Structural Glued Laminated Timber of Softwood Species

AITC 119—96

Standard Specifications for Structural Glued Laminated Timber of Hardwood Species

AITC 200—09

Manufacturing Quality Control Systems Manual for Structural Glued Laminated Timber

ANSI/AITC A 190.1—07

Structural Glued Laminated Timber

ALI

Automotive Lift Institute
P.O. Box 85
Courtland NY 13045
Standard
reference
number
TitleReferenced
in code
section number

ALI ALCTV—2007

Standard for Automobile Lifts—Safety Requirements for Construction, Testing and Validation (ANSI)

ANSI

American National Standards Institute
25 West 43rd Street, Fourth Floor
New York NY 10036
Standard
reference
number
TitleReferenced
in code
section number

A13.1—07
(Reaffirmed 2002)

Scheme for the Identification of Piping Systems

A108.1A—09

Installation of Ceramic Tile in the Wet-set Method, with Portland Cement Mortar

A108.1B—09

Installation of Ceramic Tile, quarry Tile on a Cured Portland Cement Mortar Setting
Bed with Dry-set or Latex-portland Mortar

A108.4—09

Installation of Ceramic Tile with Organic Adhesives or Water-cleanable Tile-setting Epoxy Adhesive

A108.5—09

Installation of Ceramic Tile with Dry-set Portland Cement Mortar or Latex-portland Cement Mortar

A108.6—09

Installation of Ceramic Tile with Chemical-resistant,Water Cleanable Tile-setting and -grouting Epoxy

A108.8—09

Installation of Ceramic Tile with Chemical-resistant Furan Resin Mortar and Grout

A108.9—09

Installation of Ceramic Tile with Modified Epoxy Emulsion Mortar/Grout

A108.10—09

Installation of Grout in Tilework

A118.1—10.1

American National Standard Specifications for Dry-set Portland Cement Mortar

A118.3—10.1

American National Standard Specifications for Chemical-resistant, Water-cleanable Tile-setting and
-grouting Epoxy and Water Cleanable Tile-setting Epoxy Adhesive

A118.4—10.1

American National Standard Specifications for Latex-portland Cement Mortar

A118.5—10.1

American National Standard Specifications for Chemical Resistant Furan Mortar and Grouts for Tile Installation

A118.6—10.1

American National Standard Specifications for Cement Grouts for Tile Installation

A118.8—10.1

American National Standard Specifications for Modified Epoxy Emulsion Mortar/Grout

A136.1—10.1

American National Standard Specifications for Organic Adhesives for Installation of Ceramic Tile

A137.1—08

American National Standard Specifications for Ceramic Tile

A208.1—09

Particleboard

Z 97.1—09

Safety Glazing Materials Used in Buildings—Safety Performance Specifications and Methods of Test

APA

APA - Engineered Wood Association
7011 South 19th
Tacoma WA 98466
Standard
reference
number
TitleReferenced
in code
section number

APA PDS—08

Panel Design Specification

APA PDS Supplement 1—90

Design and Fabrication of Plywood Curved Panels (revised 1995)

APA PDS Supplement 2—92

Design and Fabrication of Plywood-lumber Beams (revised 1998)

APA PDS Supplement 3—96

Design and Fabrication of Plywood Stressed-skin Panels (revised 1996)

APA PDS Supplement 4—93

Design and Fabrication of Plywood Sandwich Panels (revised 1993)

APA PDS Supplement 5—95

Design and Fabrication of All-plywood Beams (revised 1995)

EWS R540—07

Builders Tips: Proper Storage and Handling of Glulam Beams

EWS S475—07

Glued Laminated Beam Design Tables

EWS S560—10

Field Notching and Drilling of Glued Laminated Timber Beams

EWS T300—077

Glulam Connection Details

EWS X440—08

Product Guide—Glulam

EWS X450—01

Glulam in Residential Construction—Western Edition

APSP

The Association of Pool & Spa Professionals
2111 Eisenhower Avenue
Alexandria VA 22314
Standard
reference
number
TitleReferenced
in code
section number

ANSI/APSP 7—06

Standard for Suction Entrapment Avoidance in Swimming Pools, Wading Pools, Spas, Hot Tubs and Catch Basins

ASABE

American Society of Agricultural and Biological Engineers
2950 Niles Road
St. Joseph MI 49085
Standard
reference
number
TitleReferenced
in code
section number

EP 484.2—98

Diaphragm Design of Metal-clad, Post-frame Rectangular Buildings

EP 486.1—99

Shallow-post Foundation Design

EP 559—03

Design Requirements and Bending Properties for Mechanically Laminated Columns

ASCE/SEI

American Society of Civil Engineers
Structural Engineering Institute
1801 Alexander Bell Drive VA 20191-4400
Reston
Standard
reference
number
TitleReferenced
in code
section number

3—91

Structural Design of Composite Slabs

5—08

Building Code Requirements for Masonry Structures

6—08

Specification for Masonry Structures

7—05

Minimum Design Loads for Buildings and Other Structures including Supplements No. 1 and 2, excluding Chapter 14 and Appendix 11A

8—02

Standard Specification for the Design of Cold-formed Stainless Steel Structural Members

19—10

Structural Applications of Steel Cables for Buildings

24—05

Flood Resistant Design and Construction

29—05

Standard Calculation Methods for Structural Fire Protection

32—01

Design and Construction of Frost Protected Shallow Foundations

ASHRAE

American Society of Heating, Refrigerating and Air-conditioning Engineers, Inc.
1791 Tullie Circle, NE
Atlanta GA 30329-2305
Standard
reference
number
TitleReferenced
in code
section number

ASHRAE 90.1—2007

Energy Standard for Buildings Except Low-rise Residential Buildings

ASME

American Society of Mechanical Engineers
Three Park Avenue
New York NY 10016-5990
Standard
reference
number
TitleReferenced
in code
section number

A17.1/CSA B44—2010

Safety Code for Elevators and Escalators

A18.1—2008

Safety Standard for Platform Lifts and Stairway Chairlifts

A90.1—2009

Safety Standard for Belt Manlifts

B16.18—2001
(Reaffirmed 2005)

Cast Copper Alloy Solder Joint Pressure Fittings

B16.22—2001
(Reaffirmed 2005)

Wrought Copper and Copper Alloy Solder Joint Pressure Fittings

B20.1—2009

Safety Standard for Conveyors and Related Equipment

B31.3—2008

Process Piping

ASTM

ASTM International
100 Barr Harbor Drive
West Conshohocken PA 19428-2959
Standard
reference
number
TitleReferenced
in code
section number

A 36/A 36M—08

Specification for Carbon Structural Steel

A 153/A 153M—09

Specification for Zinc Coating (Hot-dip) on Iron and Steel Hardware

A 240/A 240M—10a

Standard Specification for Chromium and Chromium-nickel Stainless Steel Plate,
Sheet and Strip for Pressure Vessels and for General Applications

A 252—10

Specification for Welded and Seamless Steel Pipe Piles

A 283/A 283M—03 (2007)

Specification for Low and Intermediate Tensile Strength Carbon Steel Plates

A 307—07b

Specification for Carbon Steel Bolts and Studs, 60,000 psi Tensile Strength

A 416/A 416M—10

Specification for Steel Strand, Uncoated Seven-wire for Prestressed Concrete

A 463/A 463M—09a

Standard Specification for Steel Sheet, Aluminum-coated, by the Hot-dip Process

A 572/A 572M—07

Specification for High-strength Low-alloy Columbium-vanadium Structural Steel

A 588/A 588M—10

Specification for High-strength Low-alloy Structural Steel with 50 ksi (345 MPa)
Minimum Yield Point to 4 inches (100 mm) Thick

A 615/A 615M—09b

Specification for Deformed and Plain Billet-steel Bars for Concrete Reinforcement

A 653/A 653M—09a

Specification for Steel Sheet, Zinc-coated Galvanized or Zinc-iron Alloy-coated Galvannealed by the Hot-dip Process

A 690/A 690M—07

Standard Specification for High-strength Low-alloy Nickel, Copper, Phosphorus Steel H-piles and Sheet Piling with Atmospheric Corrosion Resistance for Use in Marine Environments

A 706/A 706M—09b

Specification for Low-alloy Steel Deformed and Plain Bars for Concrete Reinforcement

A 722/A 722M—07

Specification for Uncoated High-strength Steel Bar for Prestressing Concrete

A 755/A 755M—03 (2008)

Specification for Steel Sheet, Metallic-coated by the Hot-dip Process and Prepainted by the Coil-coating Process for Exterior Exposed Building Products

A 792/A 792M—09a

Specification for Steel Sheet, 55% Aluminum-zinc Alloy-coated by the Hot-dip Process

A 875/A 875M—09a

Standard Specification for Steel Sheet Zinc-5 percent, Aluminum Alloy-coated by the Hot-dip Process

A 913/A 913M—07

Specification for High-strength Low-alloy Steel Shapes of Structural Quality, Produced by Quenching and Self-tempering Process (QST)

A 924/A 924M—10

Standard Specification for General Requirements for Steel Sheet, Metallic-coated by the Hot-dip Process

A 992/A 992M—06a

Standard Specification for Structural Shapes

B 42—10

Specification for Seamless Copper Pipe, Standard Sizes

B 43—09

Specification for Seamless Red Brass Pipe, Standard Sizes

B 68—02

Specification for Seamless Copper Tube, Bright Annealed (Metric)

B 88—09

Specification for Seamless Copper Water Tube

B 101—07

Specification for Lead-coated Copper Sheet and Strip for Building Construction

B 209—07

Specification for Aluminum and Aluminum Alloy Steel and Plate

B 251—10

Specification for General Requirements for Wrought Seamless Copper and Copper-alloy Tube

B 280—08

Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service

B 370—09

Specification for Cold-rolled Copper Sheet and Strip for Building Construction

B 695—04 (2009)

Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

C 5—10

Specification for Quicklime for Structural Purposes

C 22/C 22M—00 (2005)e01

Specification for Gypsum

C 27—98 (2008)

Specification for Standard Classification of Fireclay and High-alumina Refractory Brick

C 28/C 28M—10

Specification for Gypsum Plasters

C 31/C 31M—10

Practice for Making and Curing Concrete Test Specimens in the Field

C 33—08

Specification for Concrete Aggregates

C 34—10

Specification for Structural Clay Load-bearing Wall Tile

C 35—01 (2009)

Specification for Inorganic Aggregates for Use in Gypsum Plaster

C 36/C 36M—03

Specification for Gypsum Wallboard

C 37/C 37M—01

Specification for Gypsum Lath

C 55—09

Specification for Concrete Building Brick

C 56—10

Specification for Structural Clay Nonload Bearing Tile

C 59/C 59M—00 (2006)

Specification for Gypsum Casting and Molding Plaster

C 61/C 61M—00 (2006)

Specification for Gypsum Keene’s Cement

C 62—10

Specification for Building Brick (Solid Masonry Units Made from Clay or Shale)

C 67—09

Test Methods of Sampling and Testing Brick and Structural Clay Tile

C 73—05

Specification for Calcium Silicate Face Brick (Sand-lime Brick)

C 79—04a

Specification for Treated Core and Nontreated Core Gypsum Sheathing Board

C 90—09

Specification for Loadbearing Concrete Masonry Units

C 91—05

Specification for Masonry Cement

C 94/C 94M—10

Specification for Ready-mixed Concrete

C 126—10

Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick and Solid Masonry Units

C 140—10

Test Method Sampling and Testing Concrete Masonry Units and Related Units

C 150—09

Specification for Portland Cement

C 172—10

Practice for Sampling Freshly Mixed Concrete

C 199—84 (2005)

Test Method for Pier Test for Refractory Mortars

C 206—03 (2009)

Specification for Finishing Hydrated Lime

C 208—08a

Specification for Cellulosic Fiber Insulating Board

C 212—10

Specification for Structural Clay Facing Tile

C 216—10

Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)

C 270—10

Specification for Mortar for Unit Masonry

C 315—07

Specification for Clay Flue Liners and Chimney Pots

C 317/C 317M—00 (2005)

Specification for Gypsum Concrete

C 330—09

Specification for Lightweight Aggregates for Structural Concrete

C 331—05

Specification for Lightweight Aggregates for Concrete Masonry Units

C 406—10

Specification for Roofing Slate

C 442/C 442M—04

Specification for Gypsum Backing Board and Coreboard and Gypsum Shaftliner Board

C 472—99 (2009)

Specification for Standard Test Methods for Physical Testing of Gypsum, Gypsum Plasters and Gypsum Concrete

C 473—10

Test Method for Physical Testing of Gypsum Panel Products

C 474—05

Test Methods for Joint Treatment Materials for Gypsum Board Construction

C 475—02 (2007)

Specification for Joint Compound and Joint Tape for Finishing Gypsum Wallboard

C 503—10

Specification for Marble Dimension Stone (Exterior)

C 514—04 (2009)e1

Specification for Nails for the Application of Gypsum Board

C 516—08

Specifications for Vermiculite Loose Fill Thermal Insulation

C 547—07e1

Specification for Mineral Fiber Pipe Insulation

C 549—06

Specification for Perlite Loose Fill Insulation

C 552—07

Standard Specification for Cellular Glass Thermal Insulation

C 557—03 (2009)e01

Specification for Adhesives for Fastening Gypsum Wallboard to Wood Framing

C 568—10

Specification for Limestone Dimension Stone

C 578—10

Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation

C 587—04 (2009)

Specification for Gypsum Veneer Plaster

C 588/C 588M—01

Specification for Gypsum Base for Veneer Plasters

C 595—10

Specification for Blended Hydraulic Cements

C 615—10

Specification for Granite Dimension Stone

C 616—10

Specification for Quartz Dimension Stone

C 629—10

Specification for Slate Dimension Stone

C 630/C 630M—03

Specification for Water-resistant Gypsum Backing Board

C 631—09

Specification for Bonding Compounds for Interior Gypsum Plastering

C 635/C 636M—08

Specification for the Manufacture, Performance and Testing of Metal Suspension
Systems for Acoustical Tile and Lay-in Panel Ceilings

C 636/C 636M—08

Practice for Installation of Metal Ceiling Suspension Systems for Acoustical Tile and Lay-in Panels

C 645—09a

Specification for Nonstructural Steel Framing Members

C 652—10

Specification for Hollow Brick (Hollow Masonry Units Made from Clay or Shale)

C 728—05 (2010)

Standard Specification for Perlite Thermal Insulation Board

C 744—10

Specification for Prefaced Concrete and Calcium Silicate Masonry Units

C 754—09a

Specification for Installation of Steel Framing Members to Receive Screw-attached Gypsum Panel Products

C 836/C 836M—10

Specification for High-solids Content, Cold Liquid-applied Elastomeric
Waterproofing Membrane for Use with Separate Wearing Course

C 840—08

Specification for Application and Finishing of Gypsum Board

C 841—03 (2008)e1

Specification for Installation of Interior Lathing and Furring

C 842—05

Specification for Application of Interior Gypsum Plaster

C 843—99 (2006)

Specification for Application of Gypsum Veneer Plaster

C 844—10

Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster

C 847—10a

Specification for Metal Lath

C 887—05 (2010)

Specification for Packaged, Dry Combined Materials for Surface Bonding Mortar

C 897—05 (2009)

Specification for Aggregate for Job-mixed Portland Cement-based Plaster

C 920—10

Standard for Specification for Elastomeric Joint Sealants

C 926—06

Specification for Application of Portland Cement-based Plaster

C 931/C 931M—04

Specification for Exterior Gypsum Soffit Board

C 932—06

Specification for Surface-applied Bonding Compounds Agents for Exterior Plastering

C 933—09

Specification for Welded Wire Lath

C 946—10

Specification for Practice for Construction of Dry-stacked, Surface-bonded Walls

C 954—10

Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to
Steel Studs from 0.033 inch (0.84 mm) to 0.112 inch (2.84 mm) in Thickness

C 955—09a

Standard Specification for Load-bearing Transverse and Axial Steel Studs, Runners Tracks, and Bracing or Bridging, for Screw Application of Gypsum Panel Products and Metal Plaster Bases

C 956—04 (2010)

Specification for Installation of Cast-in-place Reinforced Gypsum Concrete

C 957—10

Specification for High-solids Content, Cold Liquid-applied Elastomeric
Waterproofing Membrane with Integral Wearing Surface

C 960—04

Specification for Predecorated Gypsum Board

C 1002—07

Specification for Steel Self-piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs

C 1007—08a

Specification for Installation of Load Bearing (Transverse and Axial) Steel Studs and Related Accessories

C 1019—09

Test Method of Sampling and Testing Grout

C 1029—10

Specification for Spray-applied Rigid Cellular Polyurethane Thermal Insulation

C 1032—06

Specification for Woven Wire Plaster Base

C 1047—10a

Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base

C 1063—08

Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-based Plaster

C 1088—10

Specification for Thin Veneer Brick Units Made from Clay or Shale

C 1167—03 (2009)

Specification for Clay Roof Tiles

C 1177/C 1177M—08

Specification for Glass Mat Gypsum Substrate for Use as Sheathing

C 1178/C 1178M—08

Specification for Coated Mat Water-resistant Gypsum Backing Panel

C 1186—08

Specification for Flat Nonasbestos Fiber Cement Sheets

C 1261—10

Specification for Firebox Brick for Residential Fireplaces

C 1278/C 1278M—07a

Specification for Fiber-reinforced Gypsum Panels

C 1280—09

Specification for Application of Gypsum Sheathing

C 1283—07a

Practice for Installing Clay Flue Lining

C 1288—99 (2010)

Standard Specification for Discrete Nonasbestos Fiber-cement Interior Substrate Sheets

C 1289—10

Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board

C 1314—10

Test Method for Compressive Strength of Masonry Prisms

C 1325—08b

Standard Specification for Nonasbestos Fiber-mat Reinforced Cement Interior Substrate Sheets

C 1328—05

Specification for Plastic (Stucco Cement)

C 1386—07

Specification for Precast Autoclaved Aerated Concrete (AAC) Wall Construction Units

C 1395/C 1395M—06a

Specification for Gypsum Ceiling Board

C 1396—09a

Specification for Gypsum Board

C 1405—10

Standard Specification for Glazed Brick (Single Fired, Solid Brick Units)

C 1492—03 (2009)

Standard Specification for Concrete Roof Tile

C 1629/C 1629M—06

Standard Classification for Abuse-resistant Nondecorated Interior Gypsum Panel Products and Fiber-reinforced Cement Panels

C 1658/C 1658M—06

Standard Specification for Glass Mat Gypsum Panels

D 25—99 (2005)

Specification for Round Timber Piles

D 41—05 (2010)

Specification for Asphalt Primer Used in Roofing, Dampproofing and Waterproofing

D 43—00 (2006)

Specification for Coal Tar Primer Used in Roofing, Dampproofing and Waterproofing

D 56—05

Test Method for Flash Point By Tag Closed Tester

D 86—10a

Test Method for Distillation of Petroleum Products at Atmospheric Pressure

D 93—10

Test Method for Flash Point By Pensky-Martens Closed Cup Tester

D 225—07

Specification for Asphalt Shingles (Organic Felt) Surfaced with Mineral Granules

D 226/D 226M—09

Specification for Asphalt-saturated Organic Felt Used in Roofing and Waterproofing

D 227—03

Specification for Coal-tar-saturated Organic Felt Used in Roofing and Waterproofing

D 312—00 (2006)

Specification for Asphalt Used in Roofing

D 422—63 (2007)

Test Method for Particle-size Analysis of Soils

D 448—08

Standard Classification for Sizes of Aggregate for Road and Bridge Construction

D 450—07

Specification for Coal-tar Pitch Used in Roofing, Dampproofing and Waterproofing

D 635—10

Test Method for Rate of Burning and/or Extent and Time of Burning of Self-supporting Plastics in a Horizontal Position

D 1143/D 1143M—07e1

Test Method for Piles Under Static Axial Compressive Load

D 1227—95 (2007)

Specification for Emulsified Asphalt Used as a Protective Coating for Roofing

D 1557—09

Test Method for Laboratory Compaction Characteristics of Soil Using Modified Effort [56,000 ft-lb/ft3 (2,700 KN m/m3)]

D 1586—08a

Specification for Penetration Test and Split-barrel Sampling of Soils

D 1761—06

Test Method for Mechanical Fasteners in Wood

D 1863—05

Specification for Mineral Aggregate Used on Built-up Roofs

D 1929—96 (2001)e01

Test Method for Determining Ignition Properties of Plastics

D 1970—09

Specification for Self-adhering Polymer Modified Bituminous Sheet Materials
Used as Steep Roof Underlayment for Ice Dam Protection

D 2166—06

Test Method for Unconfined Compressive Strength of Cohesive Soil

D 2178—04

Specification for Asphalt Glass Felt Used in Roofing and Waterproofing

D 2216—10

Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass

D 2487—10

Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)

D 2626—04

Specification for Asphalt Saturated and Coated Organic Felt Base Sheet Used in Roofing

D 2822—05

Specification for Asphalt Roof Cement

D 2823—05

Specification for Asphalt Roof Coatings

D 2843—10

Test for Density of Smoke from the Burning or Decomposition of Plastics

D 2850—03a (2007)

Test Method for Unconsolidated, Undrained Triaxial Compression Test on Cohesive Soils

D 2898—10

Test Methods for Accelerated Weathering of Fire-retardant-treated Wood for Fire Testing

D 3019—08

Specification for Lap Cement Used with Asphalt Roll Roofing, Nonfibered, Asbestos Fibered and Nonasbestos Fibered

D 3161—09

Test Method for a Wind Resistance of Asphalt Shingles (Fan Induced Method)

D 3200—74 (2005)

Standard Specification and Test Method for Establishing Recommended Design Stresses for Round Timber Construction Poles

D 3201—08ae1

Test Method for Hygroscopic Properties of Fire-retardant-treated Wood and Wood-based Products

D 3278—96 (2004)e01

Test Methods for Flash Point of Liquids by Small Scale Closed-cup Apparatus

D 3462/D 3462M—10a

Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules

D 3468—99 (2006)e01

Specification for Liquid-applied Neoprene and Chlorosulfonated Polyethylene Used in Roofing and Waterproofing

D 3679—09a

Specification for Rigid Poly [Vinyl Chloride (PVC) Siding]

D 3689—07

Method for Testing Individual Piles Under Static Axial Tensile Load

D 3737—09

Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)

D 3746—85 (2008)

Test Method for Impact Resistance of Bituminous Roofing Systems

D 3747—79 (2007)

Specification for Emulsified Asphalt Adhesive for Adhering Roof Insulation

D 3909—97b (2004)e01

Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules

D 3957—09

Standard Practices for Establishing Stress Grades for Structural Members Used in Log Buildings

D 4022—07

Specification for Coal Tar Roof Cement, Asbestos Containing

D 4272—09

Test Method for Total Energy Impact of Plastic Films by Dart Drop

D 4318—10

Test Methods for Liquid Limit, Plastic Limit and Plasticity Index of Soils

D 4434/D 4434 M—09

Specification for Poly (Vinyl Chloride) Sheet Roofing

D 4479—07

Specification for Asphalt Roof Coatings—Asbestos-free

D 4586—07

Specification for Asphalt Roof Cement—Asbestos-free

D 4601—04

Specification for Asphalt-coated Glass Fiber Base Sheet Used in Roofing

D 4637/D 463 M—10

Specification for EPDM Sheet Used in Single-ply Roof Membrane

D 4829—08a

Test Method for Expansion Index of Soils

D 4869—05e01

Specification for Asphalt-saturated (Organic Felt) Underlayment Used in Steep Slope Roofing

D 4897/D 4897 M—01 (2009)

Specification for Asphalt-coated Glass Fiber Venting Base Sheet Used in Roofing

D 4945—08

Test Method for High-strain Dynamic Testing of Piles

D 4990—97a (2005)e01

Specification for Coal Tar Glass Felt Used in Roofing and Waterproofing

D 5019—07a

Specification for Reinforced Nonvulcanized Polymeric Sheet Used in Roofing Membrane

D 5055—10

Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-joists

D 5456—10

Specification for Evaluation of Structural Composite Lumber Products

D 5516—09

Test Method of Evaluating the Flexural Properties of Fire-retardant-treated
Softwood Plywood Exposed to the Elevated Temperatures

D 5643—06

Specification for Coal Tar Roof Cement, Asbestos-free

D 5664—10

Test Methods for Evaluating the Effects of Fire-retardant Treatment and
Elevated Temperatures on Strength Properties of Fire-retardant-treated Lumber

D 5665—99a (2006)

Specification for Thermoplastic Fabrics Used in Cold-applied Roofing and Waterproofing

D 5726—98 (2005)

Specification for Thermoplastic Fabrics Used in Hot-applied Roofing and Waterproofing

D 6083—05e01

Specification for Liquid Applied Acrylic Coating Used in Roofing

D 6162—00a (2008)

Specification for Styrene-butadiene-styrene (SBS) Modified Bituminous
Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements

D 6163—00 (2008)

Specification for Styrene-butadiene-styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements

D 6164—05e1

Specification for Styrene-butadiene-styrene (SBS) Modified Bituminous Sheet Metal Materials Using Polyester Reinforcements

D 6222—08

Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements

D 6223/D 6223M—02 (2009)e1

Specification for Atactic Polypropylene (APP) Modified Bituminous
Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements

D 6298—05e1

Specification for Fiberglass Reinforced Styrene-butadiene-styrene (SBS)
Modified Bituminous Sheets with a Factory Applied Metal Surface

D 6305—08

Practice for Calculating Bending Strength Design Adjustment Factors for Fire-retardant-treated Plywood Roof Sheathing

D 6380—03 (2009)

Standard Specification for Asphalt Roll Roofing (Organic) Felt

D 6509/D 6509M—09

Standard Specification for Atactic Polypropylene (APP) Modified Bituminous base
Sheet Materials Using Glass Fiber Reinforcements

D 6694—08

Standard Specification for Liquid-applied Silicone Coating Used in Spray Polyurethane Foam Roofing

D 6754/D 6754M—10

Standard Specification for Ketone Ethylene Ester Based Sheet Roofing

D 6757—07

Standard Specification for Inorganic Underlayment for Use with Steep Slope Roofing Products

D 6841—08

Standard Practice for Calculating Design Value Treatment Adjustment Factors for Fire-retardant-treated Lumber

D 6878—08e1

Standard Specification for Thermoplastic Polyolefin Based Sheet Roofing

D 6947—07

Standard Specification for Liquuid Applied Moisture Cured Polyurethane Coating
Used in Spray Polyurethane Foam Roofing System

D 7158—08d

Standard Test Method for Wind Resistance of Sealed Asphalt Shingles (Uplift Force/Uplift Resistance Method)

E 84—10b

Test Methods for Surface Burning Characteristics of Building Materials

E 90—09

Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements

E 96/E 96M—05

Test Method for Water Vapor Transmission of Materials

E 108—10a

Test Methods for Fire Tests of Roof Coverings

E 119—10b

Test Methods for Fire Tests of Building Construction and Materials

E 136—09b

Test Method for Behavior of Materials in a Vertical Tube Furnace at 750°C

E 330—02 (2010)

Test Method for Structural Performance of Exterior Windows, Curtain Walls and Doors by Uniform Static Air Pressure Difference

E 331—00 (2009)

Test Method for Water Penetration of Exterior Windows, Skylights, Doors and Curtain Walls by Uniform Static Air Pressure Difference

E 492—09

Test Method for Laboratory Measurement of Impact Sound Transmission Through Floor-ceiling Assemblies Using the Tapping Machine

E 605—93 (2006)

Test Method for Thickness and Density of Sprayed Fire-resistive Material (SFRM) Applied to Structural Members

E 681—09

Test Methods for Concentration Limits of Flammability of Chemical Vapors and Gases

E 736—00 (2006)

Test Method for Cohesion/Adhesion of Sprayed Fire-resistive Materials Applied to Structural Members

E 814—10

Test Method of Fire Tests of Through-penetration Firestops

E 970—10

Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source

E 1300—09a

Practice for Determining Load Resistance of Glass in Buildings

E 1354—10a

Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products
Using an Oxygen Consumption Calorimeter

E 1592—05

Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference

E 1602—03 (2010)e1

Guide for Construction of Solid Fuel-burning Masonry Heaters

E 1886—05

Test Method for Performance of Exterior Windows, Curtain Walls, Doors and
Storm Shutters Impacted by Missiles and Exposed to Cyclic Pressure Differentials

E 1966—07

Test Method for Fire-resistant Joint Systems

E 1996—09

Specification for Performance of Exterior Windows, Glazed Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes

E 2072—10

Standard Specification for Photoluminescent (Phosphorescent) Safety Markings

E 2273—03

Standard Test Method for Determining the Drainage Efficiency of Exterior Insulation and Finish Systems (EIFS) Clad Wall Assemblies

E 2307—10

Standard Test Method for Determining Fire Resistance of Perimeter Fire Barrier Systems
Using Intermediate-scale, Multistory Test Apparatus

E 2404—10

Standard Practice for Specimen Preparation and Mounting of Textile, Paper or Vinyl Wall or
Ceiling Coverings to Assess Surface Burning Characteristics

E 2568—09e1

Standard Specification for PB Exterior Insulation and Finish Systems (EIFS)

E 2570—07

Standard Test Method for Evaluating Water-resistive Barrier (WRB) Coatings Used Under Exterior Insulation and Finish Systems (EIFS) for EIFS with Drainage

E 2573—07a

Standard Practice for Specimen Preparation and Mounting of Site-fabricated Stretch Systems to Assess Surface Burning Characteristics

F 547—06

Terminology of Nails for Use with Wood and Wood-based Materials

F 1346—91 (2003)

Performance Specification for Safety Covers and Labeling Requirements for All Covers for Swimming Pools, Spas and Hot Tubs

F 1667—10

Specification for Driven Fasteners: Nails, Spikes and Staples

F 2006—10

Standard/Safety Specification for Window Fall Prevention Devices for Nonemergency Escape (Egress) and Rescue (Ingress) Windows

F 2090—10

Specification for Window Fall Prevention Devices with Emergency Escape (Egress) Release Mechanisms

F 2200—05

Standard Specification for Automated Vehicular Gate Construction

G 152—06

Practice for Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials

G 154—06

Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials

G 155—05a

Practice for Operating Xenon Arc Light Apparatus for Exposure of Nonmetallic Materials

AWCI

Association of the Wall and Ceiling Industry
513 West Broad Street, Suite 210
Falls Church VA 22046
Standard
reference
number
TitleReferenced
in code
section number

12-B—05

Technical Manual 12-B Standard Practice for the Testing and Inspection of
Field Applied Thin Film Intumescent Fire-resistive Materials; an Annotated Guide, Second Edition

AWPA

American Wood Protection Association
P.O. Box 361784
Birmingham AL 35236-1784
Standard
reference
number
TitleReferenced
in code
section number

C1—03

All Timber Products—Preservative Treatment by Pressure Processes

M4—06

Standard for the Care of Preservative-treated Wood Products

U1—10

USE CATEGORY SYSTEM: User Specification for Treated Wood Except Section 6, Commodity Specification H

AWS

American Welding Society
550 N.W. LeJeune Road
Miami FL 33126
Standard
reference
number
TitleReferenced
in code
section number

D1.1—10

Structural Welding Code—Steel

D1.3—08

Structural Welding Code—Sheet Steel

D1.4—05

Structural Welding Code—Reinforcing Steel

BHMA

Builders Hardware Manufacturers’ Association
355 Lexington Avenue, 17th Floor
New York NY 10017-6603
Standard
reference
number
TitleReferenced
in code
section number

A 156.10—05

Power Operated Pedestrian Doors

A 156.19—07

Standard for Power Assist and Low Energy Operated Doors

CGSB

Canadian General Standards Board
Place du Portage 111, 6B1
11 Laurier Street Quebec, Canada KIA 1G6
Gatineau
Standard
reference
number
TitleReferenced
in code
section number

37-GP-52M (1984)

Roofing and Waterproofing Membrane, Sheet Applied, Elastomeric

37-GP-56M (1985)

Membrane, Modified, Bituminous, Prefabricated and Reinforced for Roofing—with December 1985 Amendment

CAN/CGSB 37.54—95

Polyvinyl Chloride Roofing and Waterproofing Membrane

CPA

Composite Panel Association
19465 Deerfield Avenue, Suite 306
Leesburg VA 20176
Standard
reference
number
TitleReferenced
in code
section number

ANSI A135.4—2004

Basic Hardboard

ANSI A135.5—2004

Prefinished Hardboard Paneling

ANSI A135.6—2006

Hardboard Siding

CPSC

Consumer Product Safety Commission
4330 East West Highway
Bethesda MD 20814-4408
Standard
reference
number
TitleReferenced
in code
section number

16 CFR Part 1201(1977)

Safety Standard for Architectural Glazing Material

16 CFR Part 1209 (1979)

Interim Safety Standard for Cellulose Insulation

16 CFR Part 1301 (1977)

Ban of Unstable Refuse Bins

16 CFR Part 1404 (1979)

Cellulose Insulation

16 CFR Part 1500 (1991)

Hazardous Substances and Articles; Administration and Enforcement Regulations

16 CFR Part 1500.44 (2001)

Method for Determining Extremely Flammable and Flammable Solids

16 CFR Part 1507 (2001)

Fireworks Devices

16 CFR Part 1630 (2000)

Standard for the Surface Flammability of Carpets and Rugs

CSA

Canadian Standards Association
5060 Spectrum Way
Mississauga Ontario Canada L4W 5N6
Standard
reference
number
TitleReferenced
in code
section number

101/I.S.2/A440—08

Specifications for Windows, Doors and Unit Skylights

CSSB

Cedar Shake and Shingle Bureau
P. O. Box 1178
Sumas WA 98295-1178
Standard
reference
number
TitleReferenced
in code
section number

CSSB—97

Grading and Packing Rules for Western Red Cedar Shakes and Western Red Shingles
of the Cedar Shake and Shingle Bureau

DASMA

Door and Access Systems Manufacturers Association International
1300 Summer Avenue
Cleveland OH 44115-2851
Standard
reference
number
TitleReferenced
in code
section number

ANSI/DASMA 107—1997
(R2004)

Room Fire Test Standard for Garage Doors Using Foam Plastic Insulation

108—05

Standard Method for Testing Sectional Garage Doors and Rolling Doors:
Determination of Structural Performance Under Uniform Static Air Pressure Difference

115—05

Standard Method for Testing Sectional Garage Doors and Rolling Doors:
Determination of Structural Performance Under Missile Impact and Cyclic Wind Pressure

DOC

U.S. Department of Commerce
National Institute of Standards and Technology
1401 Constitution Avenue NW DC 20230
Washington
Standard
reference
number
TitleReferenced
in code
section number

PS-1—07

Structural Plywood

PS-2—04

Performance Standard for Wood-based Structural-use Panels

PS 20—05

American Softwood Lumber Standard

DOL

U.S. Department of Labor
c/o Superintendent of Documents
U.S. Government Printing Office DC 20402-9325
Washington
Standard
reference
number
TitleReferenced
in code
section number

29 CFR Part 1910.1000
(1974)

Air Contaminants

DOTn

U.S. Department of Transportation
c/o Superintendent of Documents
1200 New Jersey Avenue SE
Standard
reference
number
TitleReferenced
in code
section number

49 CFR Parts 100-185-2005

Hazardous Materials Regulations

49 CFR Parts 173.137 (2005)

Shippers—General Requirements for Shipments and Packaging—Class 8—Assignment of Packing Group

49 CFR—1998

Specification of Transportation of Explosive and Other Dangerous Articles, UN 0335, UN 0336 Shipping Containers

EN

European Committee for Standardization (EN)
Central Secretariat
Rue de Stassart 36
B-10 50 Brussels
Standard
reference
number
TitleReferenced
in code
section number

EN 1081-98

Resilient Floor Coverings—Determination of the Electrical Resistance

FEMA

Federal Emergency Management Agency
Federal Center Plaza
500 C Street S.W. DC 20472
Washington
Standard
reference
number
TitleReferenced
in code
section number

FIA-TB11—01

Crawlspace Construction for Buildings Located in Special Flood Hazard Areas

FM

Factory Mutual Global Research
Standards Laboratories Department
1301 Atwood Avenue P.O. Box 7500
Standard
reference
number
TitleReferenced
in code
section number

4450 (1989)

Approval Standard for Class 1 Insulated Steel Deck Roofs—with Supplements through July 1992

4470 (2010)

Approval Standard for Class 1 Roof Covers

4474 (04)

Evaluating the Simulated Wind Uplift Resistance of Roof Assemblies
Using Static Positive and/or Negative Differential Pressures

4880 (2010)

American National Standard for Evaluating Insulated Wall or Wall and Roof/
Ceiling Assemblies, Plastic Interior Finish Materials, Plastic Exterior Building Panels,
Wall/Ceiling Coating Systems, Interior and Exterior Finish Systems

GA

Gypsum Association
810 First Street N.E. #510
Washington DC 20002-4268
Standard
reference
number
TitleReferenced
in code
section number

GA 216—10

Application and Finishing of Gypsum Panel Products

GA 600—09

Fire-resistance Design Manual, 18th Edition

HPVA

Hardwood Plywood Veneer Association
1825 Michael Faraday Drive
Reston VA 20190
Standard
reference
number
TitleReferenced
in code
section number

HP-1—2009

Standard for Hardwood and Decorative Plywood

HUD

U.S. Department of Housing and Urban Development
451 7th Street, SW
Washington DC 20410
Standard
reference
number
TitleReferenced
in code
section number

HUD 24 CFR Part 3280 (1994)

Manufactured Home Construction and Safety Standards

ICC

International Code Council, Inc.
500 New Jersey Ave, NW
6th Floor
Washington DC 20001
Standard
reference
number
TitleReferenced
in code
section number

ICC/ANSI A117.1—09

Accessible and Usable Buildings and Facilities

ICC 300—07

ICC Standard on Bleachers, Folding and Telescopic Seating and Grandstands

ICC 400—07

Standard on Design and Construction of Log Structures

ICC 500—08

ICC/NSSA Standard on the Design and Construction of Storm Shelters

ICC 600—08

Standard for Residential Construction in High Wind Regions

IEBC—09

International Existing Building Code®

IECC—09

International Energy Conservation Code® (adoption includes only Section 101 of Chapter 1 and Chapters 2 through 6)

IFGC—09

International Fuel Gas Code® (including ICC Emergency Amendment changing IFGC Section 406.7)

SBCCI SSTD 11—99

Test Standard for Determining Wind Resistance of Concrete or Clay Roof Tiles

ISO

International Organization for Standardization
ISO Central Secretariat
1 ch de la Voie-Creuse, Case Postale 56
Standard
reference
number
TitleReferenced
in code
section number

ISO 8115—86

Cotton Bales–Dimensions and Density

NAAMM

National Association of Architectural Metal Manufacturers
800 Roosevelt Road, Bldg. C, Suite 312
Glen Ellyn IL 60137
Standard
reference
number
TitleReferenced
in code
section number

FP 1001—07

Guide Specifications for Design of Metal Flag Poles

NCMA

National Concrete Masonry Association
13750 Sunrise Valley
Herndon VA 22071-4662
Standard
reference
number
TitleReferenced
in code
section number

TEK 5—08

Details for Concrete Masonry Fire Walls

NFPA

National Fire Protection Association
1 Batterymarch Park
Quincy MA 02169-7471
Standard
reference
number
TitleReferenced
in code
section number

10—10

Portable Fire Extinguishers

11—10

Low Expansion Foam

12—08

Carbon Dioxide Extinguishing Systems

12A—04

Halon 1301 Fire Extinguishing Systems

13—10

Installation of Sprinkler Systems (including TIA 10-2)

13D—10

Installation of Sprinkler Systems in One- and Two-family Dwellings and Manufactured Homes (including TIA 10-2)

13R—10

Installation of Sprinkler Systems in Residential Occupancies Up to and Including Four Stories in Height (including TIA 10-2)

14—10

Installation of Standpipe and Hose System

16—07

Installation of Foam-water Sprinkler and Foam-water Spray Systems

17—09

Dry Chemical Extinguishing Systems

17A—09

Wet Chemical Extinguishing Systems

20—10

Installation of Stationary Pumps for Fire Protection

30—15

Flammable and Combustible Liquids Code

31—11

Installation of Oil-burning Equipment

32—07

Dry Cleaning Plants

37—10

Installation and Use of Stationary Combustion Engines and Gas Turbines

40—11

Storage and Handling of Cellulose Nitrate Film

58—11

Liquefied Petroleum Gas Code

61—08

Prevention of Fires and Dust Explosions in Agricultural and Food Product Facilities

70—14

National Electrical Code

72—10

National Fire Alarm and Signaling Code (including TIA 10-4 and TIA 10-5)

80—10

Fire Doors and Other Opening Protectives

85—07

Boiler and Combustion System Hazards Code
(Note: NFPA 8503 has been incorporated into NFPA 85)

92B—09

Smoke Management Systems in Malls, Atria and Large Spaces

99—05

Standard for Health Care Facilities

105—10

Standard for the Installation of Smoke Door Assemblies

110—10

Emergency and Standby Power Systems

111—10

Stored Electrical Energy Emergency and Standby Power Systems

120—10

Coal Preparation Plants

170—09

Standard for Fire Safety and Emergency Symbols

211—10

Chimneys, Fireplaces, Vents and Solid Fuel-burning Appliances

221—09

Standard for High challenge Fire Walls, Fire Walls, and Fire Barrier Walls

252—08

Standard Methods of Fire Tests of Door Assemblies

253—06

Test for Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat Energy Source

257—07

Standard for Fire Test for Window and Glass Block Assemblies

259—08

Test Method for Potential Heat of Building Materials

265—07

Method of Fire Tests for Evaluating Room Fire Growth Contribution of
Textile Wall Coverings on Full Height Panels and Walls

268—07

Standard Test Method for Determining Ignitibility of Exterior Wall Assemblies Using a Radiant Heat Energy Source

285—06

Standard Method of Test for the Evaluation of Flammability Characteristics of
Exterior Nonload-bearingWall Assemblies Containing Combustible Components

286—06

Standard Method of Fire Test for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth

288—07

Standard Method of Fire Tests of Floor Fire Door Assemblies Installed Horizontally in Fire-resistance-rated Floor Systems

409—11

Aircraft Hangars

418—06

Standard for Heliports

484—09

Combustible Metals

654—06

Prevention of Fire & Dust Explosions from the Manufacturing, Processing and Handling of Combustible Particulate Solids

655—07

Prevention of Sulfur Fires and Explosions

664—07

Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities

701—10

Standard Methods of Fire Tests for Flame-propagation of Textiles and Films

704—07

Standard System for the Identification of the Hazards of Materials for Emergency Response

1124—06

Manufacture, Transportation and Storage of Fireworks and Pyrotechnic Articles

2001—08

Clean Agent Fire Extinguishing Systems

PCI

Precast Prestressed Concrete Institute
209 W. Jackson Boulevard, Suite 500
Chicago IL 60606-6938
Standard
reference
number
TitleReferenced
in code
section number

MNL 124—89

Design for Fire Resistance of Precast Prestressed Concrete

MNL 128—01

Recommended Practice for Glass Fiber Reinforced Concrete Panels

PTI

Post-Tensioning Institute
8601 North Black Canyon Highway, Suite 103
Phoenix AZ 85021
Standard
reference
number
TitleReferenced
in code
section number

PTI—2008

Standard Requirements for Analysis of Shallow Concrete Foundations on Expansive Soils, Third Edition

PTI—2008

Standard Requirements for Design of Shallow Post-tensioned Concrete Foundation on Expansive Soils, Second Edition

RMI

Rack Manufacturers Institute
8720 Red Oak Boulevard, Suite 201
Charlotte NC 28217
Standard
reference
number
TitleReferenced
in code
section number

ANSI/MH16.1—08

Specification for Design, Testing and Utilization of Industrial Steel Storage Racks

SDI

Steel Deck Institute
P. O. Box 25
Fox River Grove IL 60021
Standard
reference
number
TitleReferenced
in code
section number

ANSI/NC1.0—06

Standard for Noncomposite Steel Floor Deck

ANSI/RD1.0—06

Standard for Steel Roof Deck

SJI

Steel Joist Institute
1173B London Links Drive
Forest VA 24551
Standard
reference
number
TitleReferenced
in code
section number

CJ-1.0—06

Standard Specification for Composite Steel Joists, CJ-series

JG-1.1—05

Standard Specification for Joist Girders

K-1.1—05

Standard Specification for Open Web Steel Joists, K-series

LH/DLH-1.1—05

Standard Specification for Longspan Steel Joists, LH-series and Deep Longspan Steel Joists, DLH-series

SPRI

Single-Ply Roofing Institute
411 Waverly Oaks Road, Suite 331B
Waltham MA 02452
Standard
reference
number
TitleReferenced
in code
section number

SPRI/ANSI/ES-1—03

Wind Design Standard for Edge Systems Used with Low Slope Roofing Systems

RP-4—02

Wind Design Guide for Ballasted Single-ply Roofing Systems

TIA

Telecommunications Industry Association
2500 Wilson Boulevard
Arlington VA 22201-3834
Standard
reference
number
TitleReferenced
in code
section number

TIA-222-G—09

Structural Standards for Steel Antenna Towers and Antenna Supporting
Structures including-Addendum 1, 222-G-1, Dated 2007

TMS

The Masonry Society
3970 Broadway, Unit 201-D
Boulder CO 80304-1135
Standard
reference
number
TitleReferenced
in code
section number

0216—07

Standard Method for Determining Fire Resistance of Concrete and Masonry Construction Assemblies

0302—07

Standard Method for Determining the Sound Transmission Class Rating for Masonry Walls

402—08

Building Code Requirements for Masonry Structures

602—08

Specification for Masonry Structures

TPI

Truss Plate Institute
218 N. Lee Street, Suite 312
Alexandria VA 22314
Standard
reference
number
TitleReferenced
in code
section number

TPI 1—2007

National Design Standards for Metal-plate-connected Wood Truss Construction

UL

Underwriters Laboratories, Inc.
333 Pfingsten Road
Northbrook IL 60062-2096
Standard
reference
number
TitleReferenced
in code
section number

9—09

Fire Tests of Window Assemblies—with Revisions through April 2005

10A—09

Tin Clad Fire Doors—with Revisions through March 2003

10B—08

Fire Tests of Door Assemblies—with Revisions through October 2001

10C—09

Positive Pressure Fire Tests of Door Assemblies—with Revisions through November 2001

14B—08

Sliding Hardware for Standard Horizontally-mounted Tin Clad Fire Doors—with Revisions through July 2000

14C—06

Swinging Hardware for Standard Tin Clad Fire Doors Mounted Singly and in Pairs

103—10

Factory-built Chimneys, for Residential Type and Building Heating Appliances—with Revisions through June 2006

127—08

Factory-built Fireplaces—with Revisions through November 2006

199E—04

Outline of Investigation for Fire Testing of Sprinklers and Water Spray Nozzles for Protection of Deep Fat Fryers

217—06

Single and Multiple Station Smoke Alarms—with Revisions through August 2005

263—03

Standard for Fire Test of Building Construction and Materials

268—09

Smoke Detectors for Fire Protective Signaling Systems—with Revisions through January 1999

300—05

Fire Testing of Fire Extinguishing Systems for Protection of Restaurant Cooking Areas

300A—06

Extinguishing system units for residential range top cooking surfaces

305—97

Panic Hardware

325—02

Door, Drapery, Gate, Louver and Window Operations and Systems—with Revisions through February 2006

555—2006

Fire Dampers

555C—2006

Ceiling Dampers

555S—99

Smoke Dampers—with Revisions through July 2006

580—2006

Test for Uplift Resistance of Roof Assemblies

641—95

Type L Low-temperature Venting Systems—with Revisions through August 2005

710B—04

Recirculating Systems—with Revisions through April 2006

723—08

Standard for Test for Surface Burning Characteristics of Building Materials—with Revisions through May 2005

790—04

Standard Test Methods for Fire Tests of Roof Coverings

793—08

Standards for Automatically Operated Roof Vents for Smoke and Heat—with Revisions through April 2004

864—03

Standards for Control Units and Accessories for Fire Alarm Systems—with Revisions through March 2006

924—06

Standard for Safety Emergency Lighting and Power Equipment

1040—96

Fire Test of Insulated Wall Construction—with Revisions through June 2001

1256—02

Fire Test of Roof Deck Construction—with Revisions through January 2007

1479—03

Fire Tests of Through-penetration Firestops—with Revisions through April 2007

1482—10

Solid-fuel-type Room Heater—with Revisions through November 2006

1715—97

Fire Test of Interior Finish Material—with Revisions through March 2004

1777—07

Chimney Liners

1784—01

Air Leakage Tests of Door Assemblies—with Revisions through December 2004

1897—04

Uplift Tests for Roof Covering Systems

1975—06

Fire Test of Foamed Plastics Used for Decorative Purposes

1994—04

Standard for Luminous Egress Path Marking Systems—with Revisions through February 2005

2017—08

Standards for General-purpose Signaling Devices and Systems—with Revisions through August 2005

2079—04

Tests for Fire Resistance of Building Joint Systems—with Revisions through March 2006

2200—12

Stationary Engine Generator Assemblies—with Revisions through July 2004

ULC

Underwriters Laboratories of Canada
7 Underwriters Road
Toronto Ontario, Canada M1R3B4
Standard
reference
number
TitleReferenced
in code
section number

CAN/ULC S102.2—2010

Standard Method of Test for Surface Burning Characteristics of Flooring,
Floor Coverings and Miscellaneous Materials and Assemblies—with 2000 Revisions

USC

United States Code
c/o Superintendent of Documents
U.S. Government Printing Office DC 20402-9325
Washington
Standard
reference
number
TitleReferenced
in code
section number

10 USC Sections 18233(A)(1) and 18237—1994
18 USC Part 1, Ch.40

Importation, Manufacture, Distribution and Storage of Explosive Materials

WDMA

Window and Door Manufacturers Association
1400 East Touhy Avenue #470
Des Plaines IL 60018
Standard
reference
number
TitleReferenced
in code
section number

AAMA/WDMA/CSA 101/I.S.2/A440—08

Specifications for Windows, Doors and Unit Skylights

WRI

Wire Reinforcement Institute, Inc.
942 Main Street, Suite 300
Hartford CT 06103
Standard
reference
number
TitleReferenced
in code
section number

WRI/CRSI—81

Design of Slab-on-ground Foundations—with 1996 Update

Resources