Heads up: There are no amended sections in this chapter.
The standards listed in Table 1701.1 are referenced in various sections of this code and shall be considered part of the requirements of this document. The standards are listed herein by the standard number and effective date, the title, application and the section(s) of this code that references the standard. The application of the referenced standard(s) shall be as specified in Section 301.2.2. The promulgating agency acronyms referred to in Table 1701.1 are defined in a list found at the end of the tables.

TABLE 1701.1
REFERENCED STANDARDS

STANDARD NUMBER STANDARD TITLE APPLICATION REFERENCED SECTIONS
ASME A112.1.2-2012 Air Gaps in Plumbing Systems (For Plumbing Fixtures and Water-Connected Receptors) Fittings Table 603.2
ASME A112.1.3-2000 (R2015) Air Gap Fittings for Use with Plumbing Fixtures, Appliances, and Appurtenances Fittings Table 603.2
ASME A112.3.1-2007 (R2012) Stainless Steel Drainage Systems for Sanitary DWV, Storm, and Vacuum Applications, Above- and Below-Ground Piping 418.1, Table 701.2, 705.7.2, 1102.1
ASME A112.3.4-2013/CSA B45.9-2013 Plumbing Fixtures with Pumped Waste and Macerating Toilet Systems Fixtures 710.13
ASME A112.4.1-2009 (R2014) Water Heater Relief Valve Drain Tubes Appliances 608.5
ASME A112.4.2-2015/CSA B45.16-2015 Personal Hygiene Devices for Water Closets Fixtures 411.4
ASME A112.4.14-2004 (R2010) Manually Operated, Quarter-Turn Shutoff Valves for Use in Plumbing Systems Valves 606.1
ASME A112.6.1M-1997 (R2012) Floor-Affixed Supports for Off-the-Floor Plumbing Fixtures for Public Use Fixtures 402.4
ASME A112.6.2-2000 (R2010) Framing-Affixed Supports for Off-the-Floor Water Closets with Concealed Tanks Fixtures 402.4
ASME A112.6.3-2001 (R2007) Floor and Trench Drains Fixtures 418.1
ASME A112.6.4-2003 (R2012) Roof, Deck, and Balcony Drains Fixtures 1102.1
ASME A112.6.7-2010 (R2015) Sanitary Floor Sinks Fixtures 421.1
ASME A112.6.9-2005 (R2015) Siphonic Roof Drains DWV Components 1106.3
ASME A112.14.1-2003 (R2012) Backwater Valves Valves 710.6
ASME A112.14.3-2000 (R2014) Grease Interceptors Fixtures 1014.1
ASME A112.14.4-2001 (R2012) Grease Removal Devices Fixtures 1014.1
ASME A112.14.6-2010 (R2015) FOG (Fats, Oils, and Greases) Disposal Systems Fixtures 1015.2
ASME A112.18.1-2012/CSA B125.1-2012 Plumbing Supply Fittings Fittings 408.3, 417.1, 417.2, 417.3, 417.4, 603.5.19
ASME A112.18.2-2015/CSA B125.2-2015 Plumbing Waste Fittings Fittings 404.1
ASME A112.18.3-2002 (R2012) Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings Backflow Protection 417.3, 417.4
ASME A112.18.6-2009/CSA B125.6-2009 (R2014) Flexible Water Connectors Piping 604.5, 604.13
ASME A112.18.9-2011 Protectors/Insulators for Exposed Waste and Supplies on Accessible Fixtures Miscellaneous 403.3
ASME A112.19.1-2013/CSA B45.2-2013 Enameled Cast Iron and Enameled Steel Plumbing Fixtures Fixtures 407.1, 408.1, 409.1, 415.1, 420.1
ASME A112.19.2-2013/CSA B45.1-2013 Ceramic Plumbing Fixtures Fixtures 407.1, 408.1, 409.1, 410.1, 411.1, 412.1, 415.1, 420.1
ASME A112.19.3-2008/CSA B45.4-2008 (R2013) Stainless Steel Plumbing Fixtures Fixtures 407.1, 408.1, 409.1, 410.1, 411.1, 415.1, 420.1
ASME A112.19.5-2011/CSA B45.15-2011 (R2016) Flush Valves and Spuds for Water Closets, Urinals, and Tanks Fixtures 413.3
ASME A112.19.7-2012/CSA B45.10-2012 Hydromassage Bathtub Systems Fixtures 409.1, 409.6
ASME A112.19.12-2014 Wall Mounted, Pedestal Mounted, Adjustable, Elevating, Tilting, and Pivoting Lavatory, Sink, and Shampoo Bowl Carrier Systems and Drain Waste Systems Fixtures 407.1, 420.1
ASME A112.19.14-2013 Six-Liter Water Closets Equipped with a Dual Flushing Device Fixtures 411.2.1
ASME A112.19.15-2012 Bathtubs/Whirlpool Bathtubs with Pressure Sealed Doors Fixtures 409.1
ASME A112.19.19-2016 Vitreous China Nonwater Urinals Fixtures 412.1
ASME B1.20.1-2013 Pipe Threads, General Purpose, Inch Joints 605.1.5, 605.2.3, 605.5.2, 605.12.3, 705.1.3, 705.3.4, 705.4.2, 705.6.3, 1208.6.10, 1309.13(2)
ASME B16.1-2015 Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250 Fittings 1208.6.13.1
ASME B16.3-2011 Malleable Iron Threaded Fittings: Classes 150 and 300 Fittings Table 604.1, Table 701.2
ASME B16.4-2011 Gray Iron Threaded Fittings: Classes 125 and 250 Fittings Table 604.1
ASME B16.5-2013 Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch Fittings 1208.6.13.2(1)
ASME B16.12-2009 (R2014) Cast Iron Threaded Drainage Fittings Fittings Table 701.2
ASME B16.15-2013 Cast Copper Alloy Threaded Fittings: Classes 125 and 250 Fittings Table 604.1
ASME B16.18-2012 Cast Copper Alloy Solder Joint Pressure Fittings Fittings Table 604.1
ASME B16.20-2012 Metallic Gaskets For Pipe Flanges: Ring-Joint, Spiral-Wound, and Jacketed Joints 1208.6.14.2
ASME B16.21-2011 Nonmetallic Flat Gaskets for Pipe Flanges Joints 1208.6.14.3
ASME B16.22-2013 Wrought Copper and Copper Alloy Solder-Joint Pressure Fittings Fittings 1308.6(3)(a), 1309.4, Table 604.1
ASME B16.23-2011 Cast Copper Alloy Solder Joint Drainage Fittings: DWV Fittings Table 701.2
ASME B16.24-2011 Cast Copper Alloy Pipe Flanges and Flanged Fittings: Classes 150, 300, 600, 900, 1500, and 2500 Fittings 1208.6.13.3
ASME B16.26-2013 Cast Copper Alloy Fittings for Flared Copper Tubes Fittings Table 604.1, 1308.6(3)(b)
ASME B16.29-2012 Wrought Copper and Wrought Copper Alloy Solder-Joint Drainage Fittings — DWV Fittings Table 701.2
ASME B16.34-2013 Valves-Flanged, Threaded, and Welding End Valves 606.1
ASME B16.42-2011 Ductile Iron Pipe and Flanged Fittings Fuel Gas Piping 1208.6.13.4
ASME B16.47-2011 Large Diameter Steel Flanges: NPS 26 through NPS 60 Metric/Inch Fittings 1208.6.13.2(2)
ASME B16.50-2013 Wrought Copper and Copper Alloy Braze-Joint Pressure Fittings Fittings Table 604.1, 1309.4, 1309.9
ASME B16.51-2013 Copper and Copper Alloy Press-Connect Pressure Fittings Fittings Table 604.1
ASME B31.3-2014 Process Piping Piping 1315.2(9)
ASME B36.10M-2015 Welded and Seamless Wrought Steel Pipe Fuel Gas, Piping 1208.6.3.1(1)
ASME BPVC Section VIII-2015 Rules for Construction of Pressure Vessels Division 1 Miscellaneous 505.4, 1313.7(2), 1314.4(2), 1313.7.1(2)
ASME BPVC Section IX-2015 Welding, Brazing, and Fusing Qualifications Qualification Standard for Welding, Brazing, and Fusing Procedures; Welders; Brazers; and Welding, Brazing, and Fusing Operators Certification 225.0, 1307.1, 1309.16.1, 1309.16.2
ASPE 45-2013 Siphonic Roof Drainage Storm Drainage 1106.2
ASSE 1001-2008 Atmospheric Type Vacuum Breakers Backflow Protection Table 603.2
ASSE 1002/ASME A112.1002/CSA B125.12-2015 Anti-Siphon Fill Valves for Water Closet Tanks Backflow Protection 413.3, Table 603.2
ASSE 1004-2008 Backflow Prevention Requirements for Commercial Dishwashing Machines Backflow Protection 414.2
ASSE 1008-2006 Plumbing Aspects of Residential Food Waste Disposer Units Appliances 419.1
ASSE 1010-2004 Water Hammer Arresters Appliances 609.10
ASSE 1011-2004 Hose Connection Vacuum Breakers Backflow Protection Table 603.2
ASSE 1013-2011 Reduced Pressure Principle Backflow Preventers and Reduced Pressure Principle Fire Protection Backflow Preventers Backflow Protection Table 603.2
ASSE 1014-2005 Backflow Prevention Devices for Hand-Held Shower Backflow Protection 417.3
ASSE 1015-2011 Double Check Backflow Prevention Assemblies and Double Check Fire Protection Backflow Prevention Assemblies Backflow Protection Table 603.2
ASSE 1016-2017/ASME A112.1016-2017/CSA B125.16-2017 Automatic Compensating Valves for Individual Showers and Tub/Shower Combinations Valves 408.3
ASSE 1018-2001 Trap Seal Primer Valves - Potable Water Supplied Valves 1007.2
ASSE 1019-2011 (R2016) Wall Hydrant with Backflow Protection and Freeze Resistance Backflow Protection Table 603.2
ASSE 1020-2004 Pressure Vacuum Breaker Assembly Backflow Protection Table 603.2
ASSE 1022-2003 Backflow Preventer for Beverage Dispensing Equipment Backflow Protection Table 603.2, 603.5.12
ASSE 1037-2015/ASME A112.1037-2015/CSA B125.37-2015 Pressurized Flushing Devices for Plumbing Fixtures Backflow Protection 413.2
ASSE 1044-2015 Trap Seal Primer - Drainage Types and Electric Design Types DWV Components 1007.2
ASSE 1047-2011 Reduced Pressure Detector Fire Protection Backflow Prevention Assemblies Backflow Protection Table 603.2
ASSE 1048-2011 Double Check Detector Fire Protection Backflow Prevention Assemblies Backflow Protection Table 603.2
ASSE 1052-2016 Hose Connection Backflow Preventers Backflow Protection Table 603.2
ASSE 1053-2004 Dual Check Backflow Preventer Wall Hydrants — Freeze Resistant Type Backflow Protection Table 603.2
ASSE 1055-2016 Chemical Dispensing Systems Backflow Protection 603.5.21
ASSE 1056-2013 Spill Resistant Vacuum Breaker Assemblies Backflow Protection Table 603.2
ASSE 1057-2012 Freeze Resistant Sanitary Yard Hydrants with Backflow Protection Backflow Protection Table 603.2
ASSE 1060-2017 Outdoor Enclosures for Fluid Conveying Components Miscellaneous 603.4.7
ASSE 1061-2015 Push-Fit Fittings Fittings Table 604.1, 605.1.3.3, 605.2.1.1, 605.3.2.1, 605.9.3
ASSE 1069-2005 Automatic Temperature Control Mixing Valves Valves 408.3
ASSE 1070-2015/ASME A112.1070-2015/CSA B125.70-2015 Water Temperature Limiting Devices Valves 407.3, 409.4, 410.3
ASSE 1071-2012 Temperature Actuated Mixing Valves for Plumbed Emergency Equipment Valves 416.2
ASSE 1079-2012 Dielectric Pipe Unions Fittings 605.15, 605.16.1, 605.16.3
ASSE Series 5000-2015 Cross-Connection Control Professional Qualifications Standard Certification 603.2, 603.4.2
ASSE Series 6000-2015 Professional Qualifications Standard for Medical Gas Systems Personnel Certification 1306.1, 1318.16.2
ASSE Series 7000-2013 Residential Potable Water Fire Protection System Installers & Inspectors for One and Two Family Dwellings Miscellaneous 612.1
ASTM A53/A53M-2012 Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless Piping Table 604.1, Table 701.2, 1208.6.3.1(2)
ASTM A74-2016 Cast Iron Soil Pipe and Fittings Piping 301.2.4, Table 701.2
ASTM A106/A106M-2015 Seamless Carbon Steel Pipe for High-Temperature Service Piping 1208.6.3.1(3)
ASTM A254/A254M-2012 Copper-Brazed Steel Tubing Piping 1208.6.4.1
ASTM A269/A269M-2015a Seamless and Welded Austenitic Stainless Steel Tubing for General Service Piping 1308.5(2)(a), Table 604.1
ASTM A312/A312M-2016a Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes Piping Table 604.1, 1308.5(2)(b)
ASTM A403/A403M-2011 Wrought Austenitic Stainless Steel Pipe Fittings Fittings 1308.5(2)(c)
ASTM A861-2004 (R2013) High-Silicon Iron Pipe and Fittings Piping 811.2
ASTM A888-2015 Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications Piping 301.2.4, Table 701.2
ASTM A1056-2012 Cast Iron Couplings used for Joining Hubless Cast Iron Soil Pipe and Fittings Fittings 705.2.2
ASTM B32-2008 (R2014) Solder Metal Joints 605.1.4, 705.3.3, 1308.6(4)
ASTM B42-2015a Seamless Copper Pipe, Standard Sizes Piping Table 604.1
ASTM B43-2015 Seamless Red Brass Pipe, Standard Sizes Piping Table 604.1, Table 701.2
ASTM B75/B75M-2011 Seamless Copper Tube Piping Table 604.1, Table 701.2
ASTM B88-2016 Seamless Copper Water Tube Piping Table 604.1, 604.4, 903.2.3, 1208.6.4.2, 1308.5(l)(a)
ASTM B135-2010 Seamless Brass Tube Piping Table 604.1
ASTM B152/B152M-2013 Copper Sheet, Strip, Plate, and Rolled Bar Miscellaneous 408.7.4
ASTM B210-2012 Aluminum and Aluminum-Alloy Drawn Seamless Tubes Piping 1208.6.4.3
ASTM B241/B241 M-2016 Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube Piping 1208.6.3.3, 1208.6.4.3
ASTM B251-2010 General Requirements for Wrought Seamless Copper and Copper-Alloy Tube Piping Table 604.1, Table 701.2
ASTM B280-2016 Seamless Copper Tube for Air Conditioning and Refrigeration Field Service Piping 1208.6.4.2, 1308.5(l)(b)
ASTM B302-2012 Threadless Copper Pipe, Standard Sizes Piping Table 604.1, Table 701.2
ASTM B306-2013 Copper Drainage Tube (DWV) Piping Table 701.2, 903.2.3
ASTM B447-2012a Welded Copper Tube Piping Table 604.1
ASTM B813-2016 Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube Joints 605.1.4, 705.3.3
ASTM B819-2000 (R2011) Seamless Copper Tube for Medical Gas Systems Piping 1308.4, 1308.5(l)(c)
ASTM B828-2016 Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings Joints 605.1.4, 705.3.3, 1308.6(4)
ASTM C4-2004 (R2014) Clay Drain Tile and Perforated Clay Drain Tile Piping Table 1101.4.6
ASTM C425-2004 (R2013) Compression Joints for Vitrified Clay Pipe and Fittings Joints 705.8.1
ASTM C564-2014 Rubber Gaskets for Cast Iron Soil Pipe and Fittings Joints 705.2.2
ASTM C700-2013 Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated Piping Table 701.2, Table 1101.4.6
ASTM Cl053-2000 (R2015) Borosilicate Glass Pipe and Fittings for Drain, Waste, and Vent (DWV) Applications Piping 811.2
ASTM C1173-2010(R2014) Flexible Transition Couplings for Underground Piping Systems Fittings 705.10
ASTM C1277-2015 Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings Fixtures 301.2.4, 705.2.2
ASTM Cl460-2012 Shielded Transition Couplings for Use With Dissimilar DWV Pipe and Fittings Above Ground Joints 705.10
ASTM C1461-2008 (R2013) Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems for Above and Below Ground Use Joints 705.10
ASTM Cl540-2015 Heavy Duty Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings Joints 705.2.2
ASTM Cl563-2008 (R2013) Gaskets for Use in Connection with Hub and Spigot Cast Iron Soil Pipe and Fittings for Sanitary Drain, Waste, Vent, and Storm Piping Applications Joints 705.2.2
ASTM Cl822-2015 Insulating Covers on Accessible Lavatory Piping Miscellaneous 403.3
ASTM D1785-2015 Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 Piping Table 604.1, Table 701.2, 1308.6(2)(a)
ASTM D2235-2004(R2016) Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings Joints 705.1.2
ASTM D2239-2012a Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter Piping Table 604.1
ASTM D2241-2015 Poly (Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series) Piping Table 604.1
ASTM D2464-2015 Threaded Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 Fittings Table 604.1
ASTM D2466-2015 Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 Fittings Table 604.1, 1308.6(2)(b)
ASTM D2467-2015 Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 Fittings Table 604.1, 1308.6(2)(b)
ASTM D2513-2014e1 Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings Piping 1208.6.5, 1208.6.7(2), 1208.6.12.2, 1210.1.7.1(1)
ASTM D2564-2012 Solvent Cements for Poly (Vinyl Chloride) (PVC) Plastic Piping Systems Joints 605.12.2, 705.6.2
ASTM D2609-2015 Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe Fittings Table 604.1
ASTM D2661-2014 Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings Piping Table 701.2
ASTM D2665-2014 Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings Piping Table 701.2
ASTM D2672-2014 Joints for IPS PVC Pipe Using Solvent Cement Joints 1308.6(2)(c)
ASTM D2680-2001 (R2014) Acrylonitrile-Butadiene-Styrene (ABS) and Poly (Vinyl Chloride) (PVC) Composite Sewer Piping Piping Table 701.2
ASTM D2683-2014 Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing Fittings Table 604.1
ASTM D2729-2011 Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings Piping Table 701.2, Table 1101.4.6
ASTM D2737-2012a Polyethylene (PE) Plastic Tubing Piping, Plastic Table 604.1
ASTM D2846/D2846M-2014 Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Hot-and Cold-Water Distribution Systems Piping Table 604.1, 605.2.2, 605.3.1, 1308.6(2)
ASTM D3034-2014a Type PSM Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings Piping, Plastic Table 701.2
ASTM D3035-2015 Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter Piping Table 604.1
ASTM D3138-2004 (R2016) Solvent Cement for Transition Joints Between Acrylonitrile-Butadiene-Styrene (ABS) and Poly (Vinyl Chloride) (PVC) Non-Pressure Piping Components Joints 705.9.4
ASTM D3139-1998 (R2011) Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals Joints 605.12.1
ASTM D3212-2007 (R2013) Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals Joints 705.1.1, 705.6.1
ASTM D3261-2016 Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing Fittings Table 604.1
ASTM D4068-2015 Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane Miscellaneous 408.7.2
ASTM D4551-2012 Poly (Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-Containment Membrane Miscellaneous 408.7.1
ASTM E84-2016 Surface Burning Characteristics of Building Materials Miscellaneous 701.2(2), 903.1(2), 1101.4
ASTM El 19-2016a Fire Tests of Building Construction and Materials Miscellaneous 1404.3, 1405.3
ASTM E814-2013a Fire Tests of Penetration Firestop Systems Miscellaneous 208.0, 222.0, 1404.3, 1405.3
ASTM F409-2012 Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings Piping, Plastic 404.1
ASTM F437-2015 Threaded Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 Fittings Table 604.1
ASTM F438-2015 Socket-Type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40 Fittings Table 604.1, 1308.6(2)(e),
ASTM F439-2013 Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 Fittings Table 604.1, 1308.6(2)(e)
ASTM F441/F441M-2015 Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80 Piping Table 604.1, 1308.6(2)(a)
ASTM F442/F442M-2013e1 Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR) Piping Table 604.1, 605.2.2
ASTM F493-2014 Solvent Cements for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe and Fittings Joints 605.2.2, 605.3.1, 1308.6(2)(g)
ASTM F628-2012e1 Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe with a Cellular Core Piping Table 701.2
ASTM F656-2015 Primers for Use in Solvent Cement Joints of Poly (Vinyl Chloride) (PVC) Plastic Pipe and Fittings Joints 605.2.2, 605.3.1, 605.12.2, 705.6.2
ASTM F667/F667M-2016 3 through 24 in. Corrugated Polyethylene Pipe and Fittings Piping, Plastic Table 1101.4.6
ASTM F714-2013 Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter Piping Table 701.2
ASTM F794-2003 (R2014) Poly (Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter Piping Table 701.2
ASTM F876-2015a Crosslinked Polyethylene (PEX) Tubing Piping Table 604.1, 605.9.1
ASTM F877-2011a Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution Systems Piping Table 604.1
ASTM F891-2010 Coextruded Poly (Vinyl Chloride) (PVC) Plastic Pipe with a Cellular Core Piping Table 701.2
ASTM F894-2013 Polyethylene (PE) Large Diameter Profile Wall Sewer and Drain Pipe Piping, Plastic Table 701.2
ASTM F1055-2016a Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing Fittings Table 604.1, 705.5.1.2
ASTM F1216-2016 Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube Piping 715.3
ASTM F1281-2011 Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe Piping Table 604.1
ASTM F1282-2010 Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe Piping Table 604.1
ASTM F1336-2015 Poly (Vinyl Chloride) (PVC) Gasketed Sewer Fittings Fittings Table 701.2
ASTM F1412-2016 Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems Piping 811.2
ASTM F1488-2014 Coextruded Composite Pipe Piping Table 701.2
ASTM F1673-2010 (R2016) Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems Piping 811.2
ASTM F1760-2001 (R2011) Coextruded Poly(Vinyl Chloride) PVC Non-Pressure Plastic Pipe Having Reprocessed Recycled Content Piping Table 701.2
ASTM F1807-2015 Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing Fittings Table 604.1
ASTM F1866-2013 Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings Fittings Table 701.2
ASTM F1960-2015 Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) Tubing Fittings Table 604.1
ASTM F1961-2009 Metal Mechanical Cold Flare Compression Fittings with Disc Spring for Crosslinked Polyethylene (PEX) Tubing Fittings Table 604.1
ASTM F1970-2012e1 Special Engineered Fittings, Appurtenances or Valves for Use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems Piping Table 604.1, 606.1
ASTM F1973-2013e1 Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems Fuel Gas 1210.1.7.1(2)
ASTM F1974-2009 (R2015) Metal Insert Fittings for Polyethylene/ Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe Fittings Table 604.1, 605.7.1, 605.10.1
ASTM F1986-2001 (R2011) Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hot and Cold Drinking-Water Systems Fittings Table 604.1
ASTM F2080-2016 Cold-Expansion Fittings with Metal Compression-Sleeves for Crosslinked Polyethylene (PEX) Pipe and SDR9 Polyethylene of Raised Temperature (PE-RT) Pipe Fittings Table 604.1
ASTM F2098-2015 Stainless Steel Clamps for Securing SDR9 Cross-linked Polyethylene (PEX) Tubing to Metal Insert and Plastic Insert Fittings Fittings Table 604.1
ASTM F2159-2014 Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing Fittings Table 604.1
ASTM F2262-2009 Crosslinked Polyethylene/Aluminum/ Crosslinked Polyethylene Tubing OD Controlled SDR9 Piping, Plastic Table 604.1
ASTM F2389-2015 Pressure-Rated Polypropylene (PP) Piping Systems Piping Table 604.1, 605.11.1, 606.1,
ASTM F2434-2014 Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Crosslinked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Tubing Fittings Table 604.1, 605.10.1
ASTM F2509-2015 Field-Assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene and Polyamide-11 (PA11) Gas Distribution Pipe and Tubing Fuel Gas 1210.1.7.1(3)
ASTM F2618-2015 Chlorinated Poly(Vinyl Chloride) CPVC Pipe and Fittings for Chemical Waste Drainage Systems Piping 811.2
ASTM F2620-2013 Heat Fusion Joining of Polyethylene Pipe and Fittings Joints 605.6.1.1, 605.6.1.3, 705.5.1.1, 705.5.1.3
ASTM F2735-2009 (R2016) Plastic Insert Fittings for SDR9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing Fittings Table 604.1
ASTM F2769-2016 Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems Piping, Fittings Table 604.1
ASTM F2831-2012 Internal Non-Structural Epoxy Barrier Coating Material Used in Rehabilitation of Metallic Pressurized Piping Systems Miscellaneous 320.1
ASTM F2855-2012 Chlorinated Poly (Vinyl Chloride)/Aluminum/Chlorinated Poly (Vinyl Chloride) (CPVC/AL/CPVC) Composite Pressure Tubing Piping Table 604.1, 605.3.1
AWS A5.8-2011 Filler Metals for Brazing and Braze Welding Joints 605.1.1, 705.3.1, 1309.4.2
AWS A5.9-2012 Bare Stainless Steel Welding Electrodes and Rods Joints 605.13.2
AWS B2.2-2010 Brazing Procedure and Performance Qualification Certification 1307.1
AWWA C110-2012 Ductile-Iron and Gray-Iron Fittings Fittings Table 604.1
AWWA C111-2012 Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and Fittings Joints 605.4.1, 605.4.2
AWWA C151-2009 Ductile-Iron Pipe, Centrifugally Cast Piping Table 604.1
AWWA C153-2011 Ductile-Iron Compact Fittings Fittings Table 604.1
AWWA C210-2015 Liquid-Epoxy Coatings and Linings for Steel Water Pipe and Fittings Miscellaneous 604.9
AWWA C500-2009 Metal-Seated Gate Valves for Water Supply Service Valves 606.1
AWWA C504-2015 Rubber-Seated Butterfly Valves Valves 606.1
AWWA C507-2015 Ball Valves, 6 in. through 60 in. (150 mm through 1,500 mm) Valves 606.1
AWWA C510-2007 Double Check Valve Backflow Prevention Assembly Backflow Protection Table 603.2
AWWA C511-2007 Reduced-Pressure Principle Backflow Prevention Assembly Backflow Protection Table 603.2
AWWA C900-2016 Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings, 4 in. through 12 in. (100 mm through 300 mm) Piping Table 604.1
AWWA C901-2008 Polyethylene (PE) Pressure Pipe and Tubing, 1/2 in. (13 mm) through 3 in. (76 mm), for Water Service Piping Table 604.1
AWWA C904-2016 Crosslinked Polyethylene (PEX) Pressure Tubing, 1/2 in. through 3 in. (13 mm through 76 mm), for Water Service Piping Table 604.1
AWWA C907-2012 Injection-Molded Polyvinyl Chloride (PVC) Pressure Fittings, 4 in. through 12 in. (100 mm through 300 mm), for Water, Wastewater, and Reclaimed Water Service Fittings Table 604.1
CGA G-4.1-2009 Cleaning Equipment for Oxygen Service Miscellaneous 1308.2, 1309.6
CISPI 301-2012 Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications Piping, Ferrous 301.2.4, Table 701.2
CISPI 310-2012 Couplings for Use in Connection with Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications Joints 301.2.4, 705.2.2
CSA B45.5-2011/IAPMO Z124-2011 (R2016) Plastic Plumbing Fixtures Fixtures 407.1, 408.1, 409.1, 411.1, 412.1, 420.1
CSA B45.8-2013/IAPMO Z403-2013 Terrazzo, Concrete, and Natural Stone Plumbing Fixtures Fixtures 407.1, 420.1
CSA B45.11-2011/IAPMO Z401-2011 Glass Plumbing Fixtures Fixtures 407.1
CSA B45.12-2013/IAPMO Z402-2013 Aluminum and Copper Plumbing Fixtures Fixtures 407.1, 408.1, 409.1, 420.1
CSA B64.1.1-2011 (R2016) Atmospheric Vacuum Breakers (AVB) Backflow Protection Table 603.2
CSA B64.1.2-2011 (R2016) Pressure Vacuum Breakers (PVB) Backflow Protection Table 603.2
CSA B64.2.1.1-2011 (R2016) Hose Connection Dual Check Vacuum Breakers (HCDVB) Backflow Protection Table 603.2
CSA B64.4-2011 (R2016) Reduced Pressure Principle (RP) Backflow Preventers Backflow Protection Table 603.2
CSA B64.4.1-2011 (R2016) Reduced Pressure Principle Backflow Preventers for Fire Protection Systems (RPF) Backflow Protection Table 603.2
CSA B64.5-2011 (R2016) Double Check Valve (DCVA) Backflow Preventers Backflow Protection Table 603.2
CSA B64.5.1-2011 (R2016) Double Check Valve Backflow Preventers for Fire Protection Systems (DCVAF) Backflow Protection Table 603.2
CSA B79-2008 (R2013) Commercial and Residential Drains and Cleanouts Fixtures 418.1
CSA B125.5/IAPMO Z2600-2011 Flexible Water Connectors with Excess Flow Shutoff Device Miscellaneous 604.5
CSA B137.1-2013 Polyethylene (PE) Pipe, Tubing, and Fittings for Cold-Water Pressure Services Piping Table 604.1
CSA B137.5-2013 Crosslinked Polyethylene (PEX) Tubing Systems for Pressure Applications Piping Table 604.1
CSA B137.6-2013 Chlorinated Polyvinylchloride (CPVC) Pipe, Tubing, and Fittings for Hot- and Cold-Water Distribution Systems Piping, Fittings Table 604.1
CSA B137.9-2013 Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure-Pipe Systems Piping Table 604.1
CSA B137.10-2013 Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Composite Pressure-Pipe Systems Piping Table 604.1
CSA B137.11-2013 Polypropylene (PP-R) Pipe and Fittings for Pressure Applications Piping Table 604.1, 605.11.1
CSA B137.18-2013 Polyethylene of Raised Temperature (PE-RT) Tubing Systems for Pressure Applications Piping, Fittings Table 604.1
CSA B181.3-2015 Polyolefin and Polyvinylidene Fluoride (PVDF) Laboratory Drainage Systems Piping 811.2
CSA B481-2012 Grease Interceptors Fixtures 1014.1
CSA LC 1-2016 Fuel Gas Piping Systems Using Corrugated Stainless Steel Tubing (same as CSA 6.26) Fuel Gas 1208.6.4.4
CSA LC 4a-2013 Press-Connect Metallic Fittings for Use in Fuel Gas Distribution Systems (same as CSA 6.32a) Fuel Gas 1208.6.11.1, 1208.6.11.2
CSA Z21.10.1-2014 Gas Water Heaters, Volume I, Storage Water Heaters with Input Ratings of 75,000 Btu Per Hour or Less (same as CSA 4.1) Fuel Gas, Appliances Table 501.1(1)
CSA Z21.10.3-2015 Gas-Fired Water Heaters, Volume III, Storage Water Heaters with Input Ratings Above 75,000 Btu Per Hour, Circulating and Instantaneous (same as CSA 4.3) Fuel Gas, Appliances Table 501.1(1)
CSA Z21.22-2015 Relief Valves for Hot Water Supply Systems (same as CSA 4.4) Valves 607.5, 608.7
CSA Z21.24-2015 Connectors for Gas Appliances (same as CSA 6.10) Fuel Gas 1212.1(3), 1212.2
CSA Z21.41-2014 Quick-Disconnect Devices for Use with Gas Fuel Appliances (same as CSA 6.9) Fuel Gas 1212.7
CSA Z21.54-2014 Gas Hose Connectors for Portable Outdoor Gas-Fired Appliances (same as CSA 8.4) Fuel Gas 1212.3.2
CSA Z21.69-2015 Connectors for Moveable Gas Appliances (same as CSA 6.16) Fuel Gas 1212.1.1
CSA Z21.75-2016 Connectors for Outdoor Gas Appliances and Manufactured Homes (same as CSA 6.27) Fuel Gas 1212.1(4)
CSA Z21.80a-2012 Line Pressure Regulators (same as CSA 6.22a) Fuel Gas 1208.8.1, 1208.8.4(1)
CSA Z21.90-2015 Gas Convenience Outlets and Optional Enclosures (same as CSA 6.24) Fuel Gas 1212.8
CSA Z21.93-2013 Excess Flow Valves for Natural and LP Gas with Pressures up to 5 psig (same as CSA 6.30) Fuel Gas 1209.1
IAPMO PS 65-2002 Airgap Units for Water Conditioning Equipment Installation Backflow Protection 611.2
IAPMO Z124.5-2013e1 Plastic Toilet Seats Appurtenance 411.3
IAPMO Z1001-2016 Prefabricated Gravity Grease Interceptors Fixtures 1014.3.4
IAPMO Z1033-2015 Flexible PVC Hoses and Tubing for Pools, Hot Tubs, Spas, and Jetted Bathtubs Tubing 409.6.1
IAPMO Z1157-2014el Ball Valves Valves 606.1
ICC A117.1-2009 Accessible and Usable Buildings and Facilities Miscellaneous 403.2, 408.6
ISEA Z358.1-2014 Emergency Eyewash and Shower Equipment Miscellaneous 416.1, 416.2
MSS SP-58-2009 Pipe Hangers and Supports - Materials, Design, Manufacture, Selection, Application, and Installation Miscellaneous 1210.2.4, 1310.5.1
MSS SP-67-2016 Butterfly Valves Valves 606.1
MSS SP-70-2011 Gray Iron Gate Valves, Flanged and Threaded Ends Valves 606.1
MSS SP-71-2011 Gray Iron Swing Check Valves, Flanged and Threaded Ends Valves 606.1
MSS SP-72-2010a Ball Valves with Flanged or Butt-Welding Ends for General Service Valves 606.1
MSS SP-78-2011 Gray Iron Plug Valves, Flanged and Threaded Ends Valves 606.1
MSS SP-80-2013 Bronze Gate, Globe, Angle, and Check Valves Valves 606.1
MSS SP-110-2010 Ball Valves Threaded, Socket-Welding, Solder Joint, Grooved and Flared Ends Valves 606.1
MSS SP-122-2012 Plastic Industrial Ball Valves Valves 606.1
NFPA 13D-2016 Installation of Sprinkler Systems in One- and Two-Family Dwellings and Manufactured Homes Miscellaneous 612.1, 612.5.3.1
NFPA 30A-2015 Motor Fuel Dispensing Facilities and Repair Garages Miscellaneous 507.14.2
NFPA 31-2016 Installation of Oil-Burning Equipment Fuel Gas, Appliances 505.3, 1201.1
NFPA 51-2018 Design and Installation of Oxygen-Fuel Gas Systems for Welding, Cutting, and Allied Processes Fuel Gas 507.9
NFPA 54/Z223.1-2015 National Fuel Gas Code Fuel Gas Chapter 5, Chapter 12
NFPA 58-2017 Liquefied Petroleum Gas Code Fuel Gas 1208.5(6), 1208.6.7(3), 1208.6.12.4, 1212.11
NFPA 70-2017 National Electrical Code Miscellaneous 1210.12.5(2), 1211.2.4, 1211.6, 1310.4.1, 1317.1(11)
NFPA 88A-2015 Parking Structures Miscellaneous 507.14.1
NFPA 99-2015 Health Care Facilities Code Miscellaneous 1301.3, 1309.8.9(6), 1317.1(9)
NFPA 211-2016 Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appliances Fuel Gas, Appliances 509.5.2, 509.5.3, 509.5.6.1, 509.5.6.3
NFPA 409-2016 Aircraft Hangars Miscellaneous 507.15
NFPA 780-2017 Installation of Lightning Protection Systems Fuel Gas 1211.4
NFPA 1192-2015 Recreational Vehicles Fuel Gas 1202.3
NSF 3-2012 Commercial Warewashing Equipment Appliances 414.1
NSF 14-2016 Plastics Piping System Components and Related Materials Miscellaneous 301.2.3, 604.1
NSF 42-2015 Drinking Water Treatment Units — Aesthetic Effects Appliances 611.1
NSF 44-2015 Residential Cation Exchange Water Softeners Appliances 611.1
NSF 53-2015 Drinking Water Treatment Units-Health Effects Appliances 611.1
NSF 55-2016 Ultraviolet Microbiological Water Treatment Systems Appliances 611.1
NSF 58-2015 Reverse Osmosis Drinking Water Treatment Systems Appliances 611.1, 611.2
NSF 61-2016 Drinking Water System Components — Health Effects Miscellaneous 415.1, 417.1, 604.1, 604.9, 606.1, 607.2, 608.2
NSF 62-2015 Drinking Water Distillation Systems Appliances 611.1
NSF 350-2014 Onsite Residential and Commercial Water Reuse Treatment Systems Miscellaneous 1506.7
NSF 359-2016 Valves for Crosslinked Polyethylene (PEX) Water Distribution Tubing Systems Valves 606.1
PDI G-101-2015 Testing and Rating Procedure for Hydro Mechanical Grease Interceptors with Appendix of Installation and Maintenance DWV Components 1014.1
PDI G-102-2010 Testing and Certification for Grease Interceptors with FOG Sensing and Alarm Devices Certification 1014.1
PDI-WH 201-2010 Water Hammer Arresters Water Supply Components 609.10
UL 17-2008 Vent or Chimney Connector Dampers for Oil-Fired Appliances (with revisions through September 25, 2013) Fuel Gas, Vent Dampers 509.14.1
UL 103-2010 Factory-Built Chimneys for Residential Type and Building Heating Appliances (with revisions through July 27, 2012) Fuel Gas, Appliances 509.5.1.1, 509.5.1.2
UL 174-2004 Household Electric Storage Tank Water Heaters (with revisions through April 10, 2015) Appliances Table 501.1(1)
UL 263-2011 Fire Tests of Building Construction and Materials (with revisions through June 2, 2015) Miscellaneous 1404.3, 1405.3
UL 378-2006 Draft Equipment (with revisions through September 17, 2013) Fuel Gas, Appliances 509.14.1
UL 399-2008 Drinking Water Coolers (with revisions through October 18, 2013) Fixtures 415.1
UL 430-2015 Waste Disposers Appliances 419.1
UL 441-2016 Gas Vents (with revisions through July 27, 2016) Fuel Gas, Vents 509.1
UL 467-2013 Grounding and Bonding Equipment Miscellaneous 1211.2.5
UL 641-2010 Type L Low-Temperature Venting Systems (with revisions through June 12, 2013) Fuel Gas 509.1
UL 651-2011 Schedule 40, 80, Type EB and A Rigid PVC Conduit and Fittings (with revisions through June 15, 2016) Piping 1208.6.6
UL 723-2008 Test for Surface Burning Characteristics of Building Materials (with revisions through August 12, 2013) Miscellaneous 701.2(2), 903.1(2), 1101.4
UL 732-1995 Oil-Fired Storage Tank Water Heaters (with revisions through October 9, 2013) Fuel Gas, Appliances Table 501.1(1)
UL 749-2013 Household Dishwashers (with revisions through May 24, 2013) Appliances 414.1
UL 778-2016 Motor-Operated Water Pumps (with revisions through November 14, 2016) Appliances 1101.14
UL 921-2016 Commercial Dishwashers Appliances 414.1
UL 959-2010 Medium Heat Appliance Factory-Built Chimneys (with revisions through June 12, 2014) Fuel Gas, Appliances 509.5.1.2
UL 1453-2016 Electric Booster and Commercial Storage Tank Water Heaters Appliances Table 501.1(1)
UL 1479-2015 Fire Tests of Penetration Firestops Miscellaneous 208.0, 222.0, 1404.3, 1405.3
UL 2523-2009 Solid Fuel-Fired Hydronic Heating Appliances, Water Heaters, and Boilers (with revisions through February 8, 2013) Fuel Gas, Appliances Table 501.1(1)
The standards, publications, practices, and guides listed in Table 1701.2 are not referenced in other sections of this code. The application of the referenced standards, publications, practices, and guides shall be as specified in Section 301.2.2. The promulgating agency acronyms are found at the end of the tables.

TABLE 1701.2
STANDARDS, PUBLICATIONS, PRACTICES, AND GUIDES

DOCUMENT NUMBER DOCUMENT TITLE APPLICATION
AHAM FWD-1-2009 Food Waste Disposers Appliances
ASCE 25-2006 Earthquake-Actuated Automatic Gas Shutoff Devices Fuel Gas
ASHRAE 90.1-2016 Energy Standard for Buildings Except Low-Rise Residential Buildings Miscellaneous
ASHRAE 90.2-2007 Energy-Efficient Design of Low-Rise Residential Buildings Miscellaneous
ASME A13.1-2007 (R2013) Scheme for the Identification of Piping Systems Piping
ASME A112.4.3-1999 (R2015) Plastic Fittings for Connecting Water Closets to the Sanitary Drainage System Fittings
ASME A112.19.10-2003 (R2008) Dual Flush Devices for Water Closets Fixtures
ASME A112.21.3M-1985 (R2007) Hydrants for Utility and Maintenance Use Valves
ASME A112.36.2M-1991 (R2012) Cleanouts DWV Components
ASME B1.20.3-1976 (R2013) Dryseal Pipe Threads, (Inch) Joints
ASME B16.33-2012 Manually Operated Metallic Gas Valves for Use in Gas Piping Systems Up to 175 psi (Sizes NPS 1/2 through NPS 2) Valves
ASME B16.39-2014 Malleable Iron Threaded Pipe Unions: Classes 150, 250 and 300 Fittings
ASME B16.40-2013 Manually Operated Thermoplastic Gas Shutoffs and Valves in Gas Distribution Systems Valves
ASME B31.1-2016 Power Piping Piping
ASME B36.19M-2004 (R2015) Stainless Steel Pipe Piping, Ferrous
ASME BPVC Section IV-2015 Rules for Construction of Heating Boilers Miscellaneous
ASSE 1003-2009 Water Pressure Reducing Valves for Domestic Water Distribution Systems Valves
ASSE 1012-2009 Backflow Preventers with an Intermediate Atmospheric Vent Backflow Protection
ASSE 1017-2009 Temperature Actuated Mixing Valves for Hot Water Distribution Systems Valves
ASSE 1023-1979 Hot Water Dispensers Household Storage Type - Electrical Appliances
ASSE 1024-2004 Dual Check Backflow Preventers Backflow Protection
ASSE 1032-2004 (R2011) Dual Check Valve Type Backflow Preventers for Carbonated Beverage Dispensers, Post Mix Type Backflow Protection
ASSE 1035-2008 Laboratory Faucet Backflow Preventers Backflow Protection
ASSE 1062-2006 Temperature Actuated, Flow, Reduction (TAFR) Valves for Individual Supply Fittings Valves
ASSE 1066-1997 Individual Pressure Balancing In-Line Valves for Individual Fixture Fittings Valves
ASTM A48/A48M-2003 (R2016) Gray Iron Castings Piping, Ferrous
ASTM A126-2004 (R2014) Gray Iron Castings for Valves, Flanges, and Pipe Fittings Piping, Ferrous
ASTM A377-2003 (R2014) Ductile-Iron Pressure Pipe Piping, Ferrous
ASTM A479/A479M-2016a Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels Piping, Ferrous
ASTM A536-1984 (R2014) Ductile Iron Castings Piping, Ferrous
ASTM A733-2015 Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe Nipples Piping, Ferrous
ASTM A1045-2010 (R2014) Flexible Poly (Vinyl Chloride) (PVC) Gaskets used in Connection of Vitreous China Plumbing Fixtures to Sanitary Drainage Systems Piping, Plastic
ASTM B29-2014 Refined Lead Joints
ASTM B370-2012 Standard Specification for Copper Sheet and Strip for Building Construction Miscellaneous
ASTM B687-1999 (R2016) Brass, Copper, and Chromium-Plated Pipe Nipples Piping, Copper Alloy
ASTM C14-2015a Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe Piping, Non-Metallic
ASTM C412-2015 Concrete Drain Tile Piping, Non-Metallic
ASTM C443-2012 Joints for Concrete Pipe and Manholes, Using Rubber Gaskets Joints
ASTM C444-2003 (R2009) Perforated Concrete Pipe Piping, Non-Metallic
ASTM C478-2015a Circular Precast Reinforced Concrete Manhole Sections Miscellaneous
ASTM C1227-2013 Precast Concrete Septic Tanks DWV Components
ASTM C1440-2008 (R2013)e1 Thermoplastic Elastomeric (TPE) Gasket Materials for Drain, Waste, and Vent (DWV), Sewer, Sanitary and Storm Plumbing Systems Joints
ASTM D1784-2011 Rigid Poly (Vinyl Chloride) (PVC) Compounds and Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds Piping, Plastic
ASTM D2321-2014e1 Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications Piping, Plastic
ASTM D2517-2006 (R2011) Reinforced Epoxy Resin Gas Pressure Pipe and Fittings Piping, Plastic
ASTM D2657-2007 (R2015) Heat Fusion Joining of Polyolefin Pipe and Fittings Joints
ASTM D2774-2012 Underground Installation of Thermoplastic Pressure Piping Piping, Plastic
ASTM D2855-2015 Two-Step (Primer and Solvent Cement) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets Joints
ASTM D3122-2015 Solvent Cement for Styrene-Rubber (SR) Plastic Pipe and Fittings Joints
ASTM D3311-2011(R2016) Drain, Waste, and Vent (DWV) Plastic Fittings Patterns Fittings
ASTM F402-2005 (R2012) Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings Joints
ASTM F446-1985 (R2009) Grab Bars and Accessories Installed in the Bathing Area Miscellaneous
ASTM F480-2014 Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80 Piping, Plastic
ASTM F810-2012 Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields Piping, Plastic
ASTM F949-2015 Poly (Vinyl Chloride) (PVC) Corrugated Sewer Pipe with a Smooth Interior and Fittings Piping, Plastic
ASTM F1476-2007 (R2013) Performance of Gasketed Mechanical Couplings for Use in Piping Applications Joints
ASTM F1499-2012 Coextruded Composite Drain, Waste, and Vent Pipe (DWV) Piping, Plastic
ASTM F1743-2008 (R2016) Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP) Piping, Plastic
ASTM F1924-2012 Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing Fittings
ASTM F1948-2015 Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas Distribution Pipe and Tubing Fittings
ASTM F2165-2013 Flexible Pre-Insulated Piping Piping, Plastic
ASTM F2206-2014 Fabricated Fittings of Butt-Fused Polyethylene (PE) DWV Components
ASTM F2306/F2306M-2014e1 12 to 60 in. [300 to 1500 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Gravity-Flow Storm Sewer and Subsurface Drainage Applications Piping, Plastic
AWS B2.4-2012 Welding Procedure and Performance Qualification for Thermoplastics Joints, Certification
AWWA C203-2015 Coal-Tar Protective Coatings and Linings for Steel Water Pipe Miscellaneous
AWWA C213-2015 Fusion-Bonded Epoxy Coatings and Linings for Steel Water Pipe and Fittings Miscellaneous
AWWA C215-2016 Extruded Polyolefin Coatings for Steel Water Pipe Miscellaneous
AWWA C606-2015 Grooved and Shouldered Joints Joints
CGA C-9-2013 Standard Color Marking of Compressed Gas Containers for Medical Use Miscellaneous
CGA S-1.3-2008 Pressure Relief Device Standards-Part 3-Stationary Storage Containers for Compressed Gases Fuel Gas
CGA V-1-2013 Compressed Gas Cylinder Valve Outlet and Inlet Connections Valves
CSA A257-2014 Concrete Pipe and Manhole Sections Piping
CSA B64.7-2011 (R2016) Laboratory Faucet Vacuum Breakers (LFVB) Backflow Protection
CSA B66-2010 (R2015) Design, Material, and Manufacturing Requirements for Prefabricated Septic Tanks and Sewage Holding Tanks DWV Components
CSA B128.1-2006/B 128.2-2006 (R2016) Design and Installation of Non-Potable Water Systems/Maintenance and Field Testing of Non-Potable Water Systems Miscellaneous
CSA B242-2005 (R2016) Groove- and Shoulder-Type Mechanical Pipe Couplings Fittings
CSA B356-2010 (R2015) Water Pressure Reducing Valves for Domestic Water Supply Systems Valves
CSA G401-2014 Corrugated Steel Pipe Products Piping, Ferrous
CSA Z21.12b-1994 (R2010) Draft Hoods Fuel Gas, Appliances
CSA Z21.13-2014 Gas-Fired Low-Pressure Steam and Hot Water Boilers (same as CSA 4.9) Fuel Gas, Appliances
CSA Z21.15b-2013 (R2014) Manually Operated Gas Valves for Appliances, Appliance Connector Valves, and Hose End Valves (same as CSA 9.1b) Fuel Gas
CSA Z21.8la-2007 (R2015) Cylinder Connection Devices (same as CSA 6.25a) Fuel Gas
CSA Z21.86-2008 (R2014) Vented Gas-Fired Space Heating Appliances (same as CSA 2.32) Fuel Gas, Appliances
CSA Z83.11-2016 Gas Food Service Equipment (same as CSA 1.8) Fuel Gas, Appliances
CSA Z317.1-2016 Special Requirements for Plumbing Installations in Health Care Facilities Miscellaneous
Energy Star-2007 (version 2.0) Program Requirements for Commercial Dishwashers Appliances
Energy Star-2015 (version 7.1) Product specification for Clothes Washers Appliances
Energy Star-2016 (version 6.0) Program Requirements for Residential Dishwashers Appliances
EPA/625/R-04/108-2004 Guidelines for Water Reuse Miscellaneous
EPA WaterSense-2007 High-Efficiency Lavatory Faucet Specification Fixtures
EPA WaterSense-2009 Specification for Flushing Urinals Fixtures
EPA WaterSense-2014 Specification for Tank-Type Toilets Fixtures
IAPMO IGC 154-2016 Shower and Tub/Shower Enclosures, Bathtubs with Glass Pressure-Sealed Doors, and Shower/Steam Panels Fixtures
IAPMO IGC 193-2010 Safety Plates, Plate Straps, Notched Plates and Safety Collars Miscellaneous
IAPMO IGC 226-2006a Drinking Water Fountains With or Without Chiller or Heater Fixtures
IAPMO IGC 276-2011 Bundled Expanded Polystyrene Synthetic Aggregate Units DWV Components
IAPMO PS 23-2006a Dishwasher Drain Airgaps Backflow Protection
IAPMO PS 25-2002 Metallic Fittings for Joining Polyethylene Pipe for Water Service and Yard Piping Joints
IAPMO PS 34-2003 Encasement Sleeve for Potable Water Pipe and Tubing Piping
IAPMO PS 36-2014e1 Lead-Free Sealing Compounds for Threaded Joints Joints
IAPMO PS 37-1990 Black Plastic PVC or PE Pressure-Sensitive Corrosion Preventive Tape Miscellaneous
IAPMO PS 42-2013e1 Pipe Alignment and Secondary Support Systems Miscellaneous
IAPMO PS 50-2010 Flush Valves with Dual Flush Device For Water Closets or Water Closet Tank with an Integral Flush Valves with a Dual Flush Device Fixtures
IAPMO PS 51-2016 Expansion Joints and Flexible Expansion Joints for DWV Piping Systems Joints
IAPMO PS 52-2009 Pump/Dose, Sumps and Sewage Ejector Tanks with or without a Pump DWV Components
IAPMO PS 53-2016 Grooved Mechanical Pipe Couplings and Grooved Fittings Joints
IAPMO PS 54-2014a Metallic and Plastic Utility Boxes Miscellaneous
IAPMO PS 57-2002 PVC Hydraulically Actuated Diaphragm Type Water Control Valves Valves
IAPMO PS 59-2016 Wastewater Diverter Valves and Diversion Systems DWV Components
IAPMO PS 60-1996 Sewage Holding Tank Containing Sewage Ejector Pump for Direct Mounted Water Closet DWV Components
IAPMO PS 63-2014 Plastic Leaching Chambers DWV Components
IAPMO PS 64-2012ae1 Roof Pipe Flashings Miscellaneous
IAPMO PS 66-2015 Dielectric Fittings Fittings
IAPMO PS 67-2010 Early-Closure Replacement Flappers or Early-Closure Replacement Flapper with Mechanical Assemblies Fixtures
IAPMO PS 69-2006 Bathwaste and Overflow Assemblies with Tub Filler Spout DWV Components
IAPMO PS 72-2007e1 Valves with Atmospheric Vacuum Breakers Valves
IAPMO PS 73-2015 Dental Liquid-Ring Vacuum Pumps Miscellaneous
IAPMO PS 76-2012a Trap Primers for Fill Valves and Flushometer Valves DWV Components
IAPMO PS 79-2005 Multiport Electronic Trap Primer DWV Components
IAPMO PS 80-2008 Clarifiers DWV Components
IAPMO PS 81-2006 Precast Concrete Seepage Pit Liners and Covers DWV Components
IAPMO PS 82-1995 Fiberglass (Glass Fiber Reinforced Thermosetting Resin) Fittings Fittings
IAPMO PS 85-1995 Tools for Mechanically Formed Tee Connections in Copper Tubing Miscellaneous
IAPMO PS 86-1995 Rainwater Diverter Valve for Non-Roofed Area Slabs DWV Components
IAPMO PS 89-1995 Soaking and Hydrotherapy (Whirlpool) Bathtubs with Hydraulic Seatlift Fixtures
IAPMO PS 90-2014 Elastomeric Test Caps, Cleanout Caps, and Combination Test Caps/Shielded Couplings DWV Components
IAPMO PS 91-2005a Plastic Stabilizers for Use with Plastic Closet Bends DWV Components
IAPMO PS 92-2013 Heat Exchangers and Indirect Water Heaters Miscellaneous
IAPMO PS 94-2012 Insulated Protectors for P-Traps, Supply Stops and Risers Miscellaneous
IAPMO PS 95-2001 Drain, Waste, and Vent Hangers and Plastic Pipe Support Hooks DWV Components
IAPMO PS 98-1996 Prefabricated Fiberglass Church Baptisteries Fixtures
IAPMO PS 100-1996 Porous Filter Protector for Sub-Drain Weep Holes DWV Components
IAPMO PS 101-1997 Suction Relief Valves Valves
IAPMO PS 104-1997 Pressure Relief Connection for Dispensing Equipment Valves
IAPMO PS 105-1997 Polyethylene Distribution Boxes DWV Components
IAPMO PS 106-2015e1 Tileable Shower Receptors and Shower Kits Fixtures
IAPMO PS 110-2006a PVC Cold Water Compression Fittings Fittings
IAPMO PS 111-1999 PVC Cold Water Gripper Fittings Fittings
IAPMO PS 112-1999 PVC Plastic Valves for Cold Water Distribution Systems Outside a Building and CPVC Plastic Valves for Hot and Cold Water Distribution Systems Valves
IAPMO PS 113-2010 Hydraulically Powered Household Food Waste Disposers Appliances
IAPMO PS 114-1999e1 Remote Floor Box Industrial Water Supply, Air Supply, Drainage Miscellaneous
IAPMO PS 115-2007 Hot Water On-Demand or Automatic Activated Hot Water Pumping Systems Miscellaneous
IAPMO PS 116-1999 Hot Water Circulating Devices Which Do Not Use a Pump Miscellaneous
IAPMO PS 117-2016 Press and Nail Connections Fittings
IAPMO PS 119-2012ae1 Water-Powered Sump Pumps Miscellaneous
IAPMO Z124.7-2013 Prefabricated Plastic Spa Shells Fixtures, Swimming Pools, Spas, and Hot Tubs
IAPMO Z124.8-2013e2 Plastic Liners for Bathtubs and Shower Receptors Fixtures
IAPMO Z1000-2013 Prefabricated Septic Tanks DWV Components
IAPMO Z1088-2013 Pre-Pressurized Water Expansion Tanks Miscellaneous
MSS SP-25-2013 Marking System for Valves, Fittings, Flanges, and Unions Miscellaneous
MSS SP-42-2013 Corrosion-Resistant Gate, Globe, Angle, and Check Valves with Flanged and Butt Weld Ends (Classes 150, 300, & 600) Piping, Ferrous
MSS SP-44-2016 Steel Pipeline Flanges Fittings
MSS SP-83-2014 Class 3000 and 6000 Pipe Unions, Socket Welding and Threaded (Carbon Steel, Alloy Steel, Stainless Steels, and Nickel Alloys) Joints
MSS SP-104-2012 Wrought Copper Solder-Joint Pressure Fittings Fittings
MSS SP-106-2012 Cast Copper Alloy Flanges and Flanged Fittings: Class 125, 150, and 300 Fittings
MSS SP-109-2012 Weld-Fabricated Copper Solder-Joint Pressure Fittings Fittings
MSS SP-123-2013 Non-Ferrous Threaded and Solder-Joint Unions for Use with Copper Water Tube Joints
NFPA 13R-2016 Installation of Sprinkler Systems in Low-Rise Residential Occupancies Miscellaneous
NFPA 80-2016 Fire Doors and Other Opening Protectives Miscellaneous
NFPA 501A-2017 Fire Safety Criteria for Manufactured Home Installations, Sites, and Communities Miscellaneous
NFPA 1981-2013 Open-Circuit Self-Contained Breathing Apparatus (SCBA) for Emergency Services Miscellaneous
NFPA 1989-2013 Breathing Air Quality for Emergency Services Respiratory Protection Miscellaneous
NFPA 5000-2015 Building Construction and Safety Code Miscellaneous
NSF 2-2015 Food Equipment Appliances
NSF 4-2014 Commercial Cooking, Rethermalization, and Powered Hot Food Holding and Transport Equipment Appliances
NSF 5-2016 Water Heaters, Hot Water Supply Boilers, and Heat Recovery Equipment Appliances
NSF 12-2012 Automatic Ice Making Equipment Appliances
NSF 18-2016 Manual Food and Beverage Dispensing Equipment Appliances
NSF 29-2012 Detergent and Chemical Feeders for Commercial Spray-Type Dishwashing Machines Appliances
NSF 40-2013 Residential Wastewater Treatment Systems DWV Components
NSF 41-2016 Non-Liquid Saturated Treatment Systems DWV Components
NSF 46-2016 Evaluation of Components and Devices Used in Wastewater Treatment Systems DWV Components
NSF 169-2012 Special Purpose Food Equipment and Devices Appliances
PSAI Z4.1-2005 For Sanitation — In Places of Employment — Minimum Requirements Miscellaneous
SAE J512-1997 Automotive Tube Fittings Fittings
SAE J1670-2008 Type "F" Clamps for Plumbing Applications Joints
TCNAA118.10-2014 Load Bearing, Bonded, Waterproof Membranes for Thin-Set Ceramic Tile and Dimension Stone Installation Miscellaneous
Title 49, Code of Federal Regulations, Part 192 Transportation of Natural and Other Gas by Pipeline: Minimum Federal Standards Miscellaneous
UL 70-2001 Septic Tanks, Bituminous-Coated Metal DWV Components
UL 80-2007 Steel Tanks for Oil-Bumer Fuels and Other Combustible Liquids (with revisions through January 16, 2014) Fuel Gas
UL 144-2012 LP-Gas Regulators (with revisions through November 5, 2014) Fuel Gas
UL 252-2010 Compressed Gas Regulators (with revisions through January 28, 2015) Fuel Gas
UL 296-2003 Oil Burners (with revisions through June 11, 2015) Fuel Gas, Appliances
UL 404-2010 Gauges, Indicating Pressure, for Compressed Gas Service (with revisions through February 11, 2015) Fuel Gas
UL 429-2013 Electrically Operated Valves Valves
UL 536-2014 Flexible Metallic Hose Fuel Gas
UL 563-2009 Ice Makers (with revisions through November 29, 2013) Appliances
UL 569-2013 Pigtails and Flexible Hose Connectors for LP-Gas Fuel Gas
UL 726-1995 Oil-Fired Boiler Assemblies (with revisions through October 9, 2013) Fuel Gas, Appliances
UL 1206-2003 Electric Commercial Clothes-Washing Equipment (with revisions through November 30, 2012) Appliances
UL 1331-2005 Station Inlets and Outlets (with revisions through August 25, 2014) Medical Gas
UL 1795-2016 Hydromassage Bathtubs (with revisions through October 7, 2016) Fixtures
UL 1951-2011 Electric Plumbing Accessories (with revisions through October 7, 2016) Miscellaneous
UL 2157-2015 Electric Clothes Washing Machines and Extractors Appliances
WQA S-300-2000 Point-of-Use Low-Pressure Reverse Osmosis Drinking Water Systems Appliances

ABBREVIATIONS IN TABLE 1701.1 AND TABLE 1701.2

AHAM Association of Home Appliance Manufacturers, 1111 19th Street, NW, Suite 402, Washington, DC 20036.
ANSI American National Standards Institute, Inc., 25 W. 43rd Street, 4th Floor, New York, NY 10036.
ASCE American Society of Civil Engineers, 1801 Alexander Bell Drive, Reston, VA 20191—4400.
ASHRAE American Society of Heating, Refrigerating, and Air Conditioning Engineers, Inc., 1791 Tullie Circle, NE, Atlanta, GA 30329—2305.
ASME American Society of Mechanical Engineering, Two Park Avenue, New York, NY 10016—5990.
ASPE American Society of Plumbing Engineers, 6400 Shafer Court, Suite 350, Rosemont, IL 60018.
ASSE American Society of Sanitary Engineering, 18927 Hickory Creek Drive, Suite 220, Mokena, IL 60448.
ASTM ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428—2959.
AWS American Welding Society, 8669 NW 36 Street, #130 Miami, FL 33166—6672.
AWWA American Water Works Association, 6666 W. Quincy Avenue, Denver, CO 80235.
CFR U.S Government Publishing Office, 723 North Capitol Street, N.W. Washington, DC 20401—001
CGA Compressed Gas Association, 14501 George Carter Way, Suite 103, Chantilly, VA 20151.
CISPI Cast-Iron Soil Pipe Institute, 2401 Fieldcrest Drive, Mundelein, IL 60060.
CSA Canadian Standards Association, 178 Rexdale Boulevard, Toronto, Ontario, Canada, M9W 1R3.
el An editorial change since the last revision or reapproval.
ENERGY STAR 1200 Pennsylvania Avenue, N.W., Washington, D.C. 20460.
EPAWATERSENSE U.S. Environmental Protection Agency, Office of Wastewater Management (4204M), 1200 Pennsylvania Avenue, N.W., Washington, D.C. 20460.
IAPMO International Association of Plumbing and Mechanical Officials, 4755 E. Philadelphia Street, Ontario, CA 91761.
ICC International Code Council, 500 New Jersey Avenue, NW, 6th Floor, Washington, DC 20001.
ISEA International Safety Equipment Association, 1901 N. Moore Street, Suite 808, Arlington, VA 22209—1762.
MSS Manufacturers Standardization Society of the Valve and Fittings Industry, 127 Park Street, NE, Vienna, VA 22180.
NFPA National Fire Protection Association, 1 Batterymarch Park, Quincy, MA 02169—7471.
NSF NSF International, 789 N. Dixboro Road, Ann Arbor, MI 48105.
PDI Plumbing and Drainage Institute, 800 Turnpike Street, Suite 300, North Andover, MA 01845.
PSAI Portable Sanitation Association International, 2626 E 82nd Street, Suite 175, Bloomington, MN 55425.
SAE Society of Automotive Engineers, 400 Commonwealth Drive, Warrendale, PA 15096.
TCNA Tile Council of North America, Inc. 100 Clemson Research Blvd., Anderson, SC 29625.
UL Underwriters Laboratories, Inc., 333 Pfingsten Road, Northbrook, IL 60062.
WQA Water Quality Association, 4151 Naperville Road, Lisle, IL 60532—3696.
UpCodes Premium
Leverage the most sophisticated code compliance platform.
TRY FREE FOR TWO WEEKS VISIT PRICING