CODES

ADOPTS WITH AMENDMENTS:

International Residential Code 2015 (IRC 2015)

Chapter 1 Scope and Administration

Chapter 2 Definitions

Chapter 3 Building Planning

Chapter 4 Foundations

Chapter 5 Floors

Chapter 6 Wall Construction

Chapter 7 Wall Covering

Chapter 8 Roof-Ceiling Construction

Chapter 9 Roof Assemblies

Chapter 10 Chimneys and Fireplaces

Chapter 11 [Re] Energy Efficiency

Chapter 12 Mechanical Administration

Chapter 13 General Mechanical System Requirements

Chapter 14 Heating and Cooling Equipment and Appliances

Chapter 15 Exhaust Systems

Chapter 16 Duct Systems

Chapter 17 Combustion Air

Chapter 18 Chimneys and Vents

Chapter 19 Special Appliances, Equipment and Systems

Chapter 20 Boilers and Water Heaters

Chapter 21 Hydronic Piping

Chapter 22 Special Piping and Storage Systems

Chapter 23 Solar Thermal Energy Systems

Chapter 24 Fuel Gas

Chapter 25 Plumbing Administration

Chapter 26 General Plumbing Requirements

Chapter 27 Plumbing Fixtures

Chapter 28 Water Heaters

Chapter 29 Water Supply and Distribution

Chapter 30 Sanitary Drainage

Chapter 31 Vents

Chapter 32 Traps

Chapter 33 Storm Drainage

Chapter 34 General Requirements

Chapter 35 Electrical Definitions

Chapter 36 Services

Chapter 37 Branch Circuit and Feeder Requirements

Chapter 38 Wiring Methods

Chapter 39 Power and Lighting Distribution

Chapter 40 Devices and Luminaires

Chapter 41 Appliance Installation

Chapter 42 Swimming Pools [Electrical Provisions]

Chapter 43 Class 2 Remote-Control, Signaling and Power-Limited Circuits

Chapter 44 High-Velocity Hurricane Zones

Chapter 45 Private Swimming Pools

Chapter 46 Referenced Standards

Appendix A Sizing and Capacities of Gas Piping

Appendix B Sizing of Venting Systems Serving Appliances Equipped With Draft Hoods, Category I Appliances, and Appliances Listed for Use With Type B Vents

Appendix C Exit Terminals of Mechanical Draft and Direct-Vent Venting Systems

Appendix D Recommended Procedure for Safety Inspection of an Existing Appliance Installation

Appendix E Florida Standard for Mitigation of Radon in Existing Buildings Effective: June 1, 1994

Appendix F Florida Standard for Passive Radon-Resistant New Residential Building Construction

Appendix G Piping Standards for Various Applications

Appendix H Patio Covers

Appendix I Private Sewage Disposal

Appendix J Existing Buildings and Structures

Appendix K Sound Transmission

Appendix L Permit Fees

Appendix M Home Day Care—r-3 Occupancy

Appendix N Venting Methods

Appendix O Automatic Vehicular Gates

Appendix P Sizing of Water Piping System

Appendix Q Reserved

Appendix R Light Straw-Clay Construction

Appendix S Strawbale Construction

Appendix T Recommended Procedure for Worst-Case Testing of Atmospheric Venting Systems Under N1102.4 or N1105 Conditions ≤ 5ach 50

Appendix U Solar-Ready Provisions—detached One- And Two-Family Dwellings, Multiple Single- Family Dwellings (Townhouses)

This chapter lists the standards that are referenced in various sections of this document. The standards are listed herein by the promulgating agency of the standard, the standard identification, the effective date and title, and the section or sections of this document that reference the standard. The application of the referenced standards shall be as specified in Section 102.4.

AAF

Aluminum Association of Florida, Inc.
3751 Maguire Blvd, Suite 260
<span class="changed_nonICC_FL">Orlando</span> <span class="changed_nonICC_FL">Florida</span> <span class="changed_nonICC_FL">32803</span>
Standard
reference
number
TitleReferenced
in code

AAF—2014

Guide to Aluminum Construction in High Wind Areas 2014

R301.2.1.1.1

AAMA

American Architectural Manufacturers Association
1827 Walden Office Square, Suite 550
Schaumburg IL 60173
Standard
reference
number
TitleReferenced
in code
section number

AAMA/WDMA/CSA 101/I.S.2/A440—08 or 11

North American Fenestration Standards/Specifications for Windows, Doors and Skylights

R308.6.9, R609.3

450—10

Voluntary Performance Rating Method for Mulled Fenestration Assemblies

R609.8

506—11

Voluntary Specifications for Hurricane Impact and Cycle Testing of Fenestration Products

R609.6.1

711—13

Voluntary Specification for Self-adhering Flashing Used for Installation of Exterior Wall Fenestration Products

R703.4

712—11

Voluntary Specification for Mechanically Attached Flexible Flashing

R703.4

714—12 or 15

Voluntary Specification for Liquid Applied Flashing Used to Create a Water-resistive Seal around Exterior Wall Openings in Buildings

R703.4

800—16

Voluntary Specifications and Test Methods for Sealants

R703.4

812—04(2010

Voluntary Practice for Assessment of Single Component Aerosol Expanding Polyurethane Foams for Sealing Rough Openings of Fenestration Installations

R703.4

AAMA/NPEA/NSA 2100—12

Specifications for Sunrooms

FMA/AAMA 100—12

Standard Practice for the Installation of Windows with Flanges or Mounting

R703.4

FMA/AAMA 200—12

Standard Practice for the Installation of Windows with Frontal Flanges for Surface Barrier Masonry

R703.4

FMA/WDMA 250—10

Standard Practice for the Installation of Non-Frontal Flange Windows with Mounting Flanges for Surface Barrier Masonry for Extreme Wind/Water Conditions

R703.4

FMA/AAMA/WDMA 300—12

Standard Practice for the Installation of Exterior Doors in Wood Frame Construction for Extreme Wind/Water Exposure

R703.4

FMA/AAMA/WDMA 400—13

Standard Practice for the Installation of Exterior Doors in Surface Barrier Masonry Construction for Extreme Wind/Weather Exposure

R703.4

ACCA

Air Conditioning Contractors of America
2800 Shirlington Road, Suite 300
Arlington VA 22206
Standard
reference
number
TitleReferenced
in code
section number

Manual D—2011

Residential Duct Systems

M1601.1, M1602.2

Manual J—2011

Residential Load Calculation—Eighth Edition

M1401.3

Manual S—13

Residential Equipment Selection

M1401.3

ACI

American Concrete Institute
38800 Country Club Drive
Farmington Hills MI 48331
Standard
reference
number
TitleReferenced
in code
section number

332—14

Code Requirements for Residential Concrete Construction

R402.2, R403.1, R404.1.3, R404.1.3.4, R404.1.4.2, R506.1

332—14

Residential Code Requirements for Structural Concrete

506.1, 506.2.4.2

530—13

Building Code Requirements for Masonry Structures

R318.4, R404.1.2, R606.1, R606.1.1, R606.12.1, R606.12.2.3.2, R606.12.2.3.1, R606.12.3.1, R703.8, R703.12

530.1—13

Specification for Masonry Structures

R404.1.2, R606.1, R606.1.1, R606.2.9, R606.2.12, R606.12.1, R606.12.2.3.2, R606.12.3.1, 703.12

AISI

American Iron and Steel Institute
25 Massachusetts Avenue, NW Suite 800
Washington DC 20001
Standard
reference
number
TitleReferenced
in code
section number

AISI S100—12

North American Specification for the Design of Cold-formed Steel Structural Members, 2012

R505.1.3, R603.6, R608.9.2, R608.9.3, R804.3.6

AISI S200—12

North American Standard for Cold-formed Steel Framing—General Provisions 2012

R702.3.3

AISI S220—11

North American Standard for Cold-formed Steel Framing—Nonstructural Members

R702.3.3

AISI S230—07/S3-12 (2012)

Standard for Cold-formed Steel Framing—Prescriptive Method for One- and Two-family Dwellings, 2007 with Supplement 3, dated 2012 (Reaffirmed 2012)

R301.1.1, R301.2.1.1, R301.2.2.3.1, R301.2.2.3.5, R603.6, R603.9.4.1, R603.9.4.2, R608.9.2, R608.9.3, Figure 608.9(11), R608.10

AMCA

Air Movement and Control Association
300 West University
Arlington Heights IL 60004
Standard
reference
number
TitleReferenced
in code
section number

ANSI/AMCA 210-ANSI/ASHRAE 51—07

Laboratory Methods of Testing Fans for Aerodynamic Performance Rating

Table M1506.2

ANCE

Association of the Electric Sector
Av. Lázaro Cardenas No. 869
Col. Nueva Industrial Vallejo
México D.F. C.P. 07700
Standard
reference
number
TitleReferenced
in code
section number

UL/CSA/ANCE 60335-2—2012

Standard for Household and Similar Electric Appliances, Part 2: Particular Requirements for Motor-compressors

M1403.1, M1412.1, M1413.1

ANSI

American National Standards Institute
25 West 43rd Street, Fourth Floor
New York NY 10036
Standard
reference
number
TitleReferenced
in code
section number

A108.1A—99

Installation of Ceramic Tile in the Wet-set Method, with Portland Cement Mortar

R702.4.1

A108.1B—99

Installation of Ceramic Tile, Quarry Tile on a Cured Portland Cement Mortar Setting Bed with Dry-set or Latex Portland Mortar

R702.4.1

A108.4—99

Installation of Ceramic Tile with Organic Adhesives or Water-Cleanable Tile-setting Epoxy Adhesive

R702.4.1

A108.5—99

Installation of Ceramic Tile with Dry-set Portland Cement Mortar or Latex Portland Cement Mortar

R702.4.1

A108.6—99

Installation of Ceramic Tile with Chemical-resistant, Water-cleanable Tile-setting and -grouting Epoxy

R702.4.1

A108.11—99

Interior Installation of Cementitious Backer Units

R702.4.1

A118.1—99

American National Standard Specifications for Dry-set Portland Cement Mortar

R702.4.1

A118.3—99

American National Standard Specifications for Chemical-resistant, Water-cleanable Tile-setting and -grouting Epoxy, and Water-cleanable Tile-setting Epoxy Adhesive

R702.4.1

A118.4—99

American National Standard Specifications for Latex-Portland Cement Mortar

R606.2.10

A118.10—99

Specification for Load-bearing, Bonded, Waterproof Membranes for Thin-set Ceramic Tile and Dimension Stone Installation

P2709.2, P2709.2.4

A136.1—99

American National Standard Specifications for Organic Adhesives for Installation of Ceramic Tile

R702.4.1

A137.1—2012

American National Standard Specifications for Ceramic Tile

R702.4.1

LC1/CSA 6.26—13

Fuel Gas Piping Systems Using Corrugated Stainless Steel Tubing (CSST)

G2414.5.3

LC4/CSA 6.32—12

Press-connect Metallic Fittings for Use in Fuel Gas Distribution Systems

G2414.10.2

Z21.1—2010

Household Cooking Gas Appliances

G2447.1

Z21.5.1/CSA 7.1—14

Gas Clothes Dryers—Volume I—Type I Clothes Dryers

G2438.1

Z21.8—94 (R2002)

Installation of Domestic Gas Conversion Burners

G2443.1

Z21.10.1/CSA 4.1—12

Gas Water Heaters—Volume I—Storage Water Heaters with Input Ratings of 75,000 Btu per hour or Less

G2448.1

Z21.10.3/CSA 4.3—11

Gas Water Heaters—Volume III—Storage Water Heaters with Input Ratings above 75,000 Btu per hour, Circulating and Instantaneous

G2448.1

Z21.11.2—11

Gas-fired Room Heaters—Volume II—Unvented Room Heaters

G2445.1

Z21.13/CSA 4.9—11

Gas-fired Low-pressure Steam and Hot Water Boilers

G2452.1

Z21.15/CSA 9.1—09

Manually Operated Gas Valves for Appliances, Appliance Connector Valves and Hose End Valves

Table G2420.1.1

Z21.22—99 (R2003)

Relief Valves for Hot Water Supply Systems—with Addenda Z21.22a—2000 (R2003) and 21.22b—2001 (R2003)

P2804.2, P2804.7

Z21.24/CGA 6.10—06

Connectors for Gas Appliances

G2422.1

Z21.40.1/CSA 2.91—96 (R2011)

Gas-fired, Heat-activated Air-conditioning and Heat Pump Appliances

G2449.1

Z21.40.2/CSA 2.92—96 (R2011)

Air-conditioning and Heat Pump Appliances (Thermal Combustion)

G2449.1

Z21.42—2014

Gas-fired Illuminating Appliances

G2450.1

Z21.47/CSA 2.3—12

Gas-fired Central Furnaces

G2442.1

Z21.50/CSA 2.22—12

Vented Gas Fireplaces

G2434.1

Z21.56/CSA 4.7—13

Gas-fired Pool Heaters

G2441.1

Z21.58—95/CSA 1.6—13

Outdoor Cooking Gas Appliances

G2447.1

Z21.60/CSA 2.26—12

Decorative Gas Appliances for Installation in Solid Fuel-burning Fireplaces

G2432.1

Z21.75/CSA 6.27—07

Connectors for Outdoor Gas Appliances and Manufactured Homes

G2422.1

Z21.80—11

Line Pressure Regulators

G2421.1

ANSI/CSA America

Stationary Fuel Cell Power Systems

M1903.1

FCI—12 Z21.84—12

Manually Listed, Natural Gas Decorative Gas Appliances for Installation in Solid Fuel-burning Fireplaces

G2432.1, G2432.2

Z21.86—08

Gas-fired Vented Space Heating Appliances

G2436.1, G2437.1, G2446.1

Z21.88/CSA 2.33—14

Vented Gas Fireplace Heaters

G2435.1

Z21.91—07

Ventless Firebox Enclosures for Gas-fired Unvented Decorative Room Heaters

G2445.7.1

Z21.97—12

Outdoor Decorative Appliances

G2454.1

Z83.6—90 (R1998)

Gas-fired Infrared Heaters

G2451.1

Z83.8/CSA 2.6—09

Gas-fired Unit Heaters, Gas Packaged Heaters, Gas Utility Heaters and Gas-fired Duct Furnaces

G2444.1

Z83.19—01 (R2009)

Gas-fuel High-intensity Infrared Heaters

G2451.1

Z83.20—08

Gas-fired Low-intensity Infared Heaters Outdoor Decorative Appliances

G2451.1

Z97.1—2014

Safety Glazing Materials Used in Buildings—Safety Performance Specifications and Methods of Test

R308.1.1, R308.3.1

APA

APA—The Engineered Wood Association
7011 South 19th
Tacoma WA 98466
Standard
reference
number
TitleReferenced
in code
section number

ANSI/A190.1—12

Structural Glued-laminated Timber

R502.1.3, R602.1.3, R802.1.2

ANSI/APA PRP 210—08

Standard for Performance-rated Engineered Wood Siding

R604.1, Table R703.3(1), R703.3.3

ANSI/APA PRG 320—2012

Standard for Performance-rated Cross Laminated Timber

R502.1.6, R602.1.6, R802.1.6

ANSI/APA PRR 410—2011

Standard for Performance-rated Engineered Wood Rim Boards

R502.1.7, R602.1.7, R802.1.7

APA E30—11

Engineered Wood Construction Guide

Table R503.2.1.1(1), R503.2.2, R803.2.2, R803.2.3

APSP

Association of Pool & Spa Professionals
2111 Eisenhower Avenue, Suite 500
Alexandria VA 22314
Standard
reference
number
TitleReferenced
in code
section number

ANSI/APSP/ICC 3—14

American National Standard for Permanently Installed Residential Spas and Swim Spas

R4501.6.1

ANSI/APSP/ICC 4—12

American National Standard for Above-ground/On-ground Residential Swimming Pools

R4501.6.1

ANSI/APSP/ICC 5—11

American National Standard for Residential In-ground Swimming Pools

R4501.6.1

ANSI/APSP/ICC 6—13

American National Standard for Residential Portable Spas and Swim Spas

R4501.6.1

ANSI/APSP/ICC 7—13

American National Standard for Suction Entrapment Avoidance in Swimming Pools, Wading Pools, Spas, Hot Tubs and Catch Basins

R4501.6.1, R4501.6.3, R4501.6.6

ASCE/SEI

American Society of Civil Engineers
Structural Engineering Institute
1801 Alexander Bell Drive
Reston VA 20191
Standard
reference
number
TitleReferenced
in code
section number

5—13

Building Code Requirements for Masonry Structures

R404.1.2, R606.1, R606.1.1, R606.12.1, R606.12.2.3.1, R606.12.2.3.2, R606.12.3.1, R703.12

6—13

Specification for Masonry Structures

R404.1.2, R606.1, R606.1.1, R606.2.9, R606.2.12, R606.12.1, R606.12.2.3.1, R606.12.2.3.2, R606.12.3.1, R703.12

7—10

Minimum Design Loads for Buildings and Other Structures with Supplement No. 1

R301.2.1.1, R301.2.1.2, R301.2.1.2.1, R301.2.1.5, R301.2.1.5.1, Table R608.6(1), Table R608.6(2), Table R608.6(3), Table R608.6(4), Table R608.7(1A), Table R608.7(1B), Table R608.7(1C), R608.9.2, R608.9.3, R609.2R609.4

24—14

Flood-resistant Design and Construction

R301.2.4, R301.2.4.1, R322.1, R322.1.1, R322.1.6, R322.1.9, R322.2.2, R322.3.3

32—01

Design and Construction of Frost-protected Shallow Foundations

R403.1.4.1

ASHRAE

American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.
1791 Tullie Circle, NE
Atlanta GA 30329
Standard
reference
number
TitleReferenced
in code
section number

ASHRAE—2013

ASHRAE Handbook of Fundamentals

P3001.2, P3101.4

34—2013

Designation and Safety Classification of Refrigerants

M1411.1

ASME

American Society of Mechanical Engineers
Three Park Avenue
New York NY 10016-5990
Standard
reference
number
TitleReferenced
in code
section number

ASME/A17.1/CSA B44—2013

Safety Code for Elevators and Escalators

R321.1

A18.1—2008

Safety Standard for Platforms and Stairway Chair Lifts

R321.2

A112.1.2—2004

Air Gaps in Plumbing Systems

P2717.1, Table P2902.3, P2902.3.1

A112.1.3—2000 (Reaffirmed 2011)

Air Gap Fittings for Use with Plumbing Fixtures, Appliances and Appurtenances

Table P2701.1, P2717.1, Table P2902.3, P2902.3.1

A112.3.1—2007

Stainless Steel Drainage Systems for Sanitary, DWV, Storm and Vacuum Applications Above and Below Ground

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3002.3, Table P3302.1

A112.3.4—2013/CSA B45.9—13

Macerating Toilet Systems and Related Components

Table P2701.1, P3007.5

A112.4.1—2009

Water Heater Relief Valve Drain Tubes

P2804.6.1

A112.4.2—2009

Water-closet Personal Hygiene Devices

P2722.5

A112.4.3—1999 (R2010)

Plastic Fittings for Connecting Water Closets to the Sanitary Drainage System

P3003.14

A112.4.14—2004 (R2010)

Manually Operated, Quarter-turn Shutoff Valves for Use in Plumbing Systems

Table P2903.9.4

A112.6.1M—1997 (R2008)

Floor-affixed Supports for Off-the-floor Plumbing Fixtures for Public Use

Table P2701.1, P2702.4

A112.6.2—2000 (R2010)

Framing-affixed Supports for Off-the-floor Water Closets with Concealed Tanks

Table P2701.1, P2702.4

A112.6.3—2001 (R2007)

Floor and Trench Drains

Table P2701.1

A112.14.1—03 (Reaffirmed 2008)

Backwater Valves

P3008.2

A112.18.2—2011/CSA B125.2—2011

Plumbing Waste Fittings

Table P2701.1, P2702.2

A112.18.3—2002 (Reaffirmed 2008)

Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings

P2708.5, P2722.3

A112.18.6/CSA B125.6—2009

Flexible Water Connectors

P2906.7

A112.19.1—2013/CSA B45.2—2013

Enameled Cast-iron and Enameled Steel Plumbing Fixtures

Table P2701.1, P2711.1

A112.19.2—2013/CSA B45.1—2013

Ceramic Plumbing Fixtures

Table P2701.1, P2705.1, P2711.1, P2712.1, P2712.2, P2712.9

A112.19.3—2008/CSA B45.4—08 (R2013)

Stainless Steel Plumbing Fixtures

Table P2701.1, P2705.1, P2711.1, P2712.1

A112.19.5—2011/CSA B45.15—2011

Flush Valves and Spuds for Water-closets, Urinals and Tanks

Table P2701.1

A112.19.7/2012 CSA B45.10—2012

Hydromassage Bathtub Systems

Table P2701.1

A112.19.12—2006

Wall-mounted and Pedestal-mounted, Adjustable and Pivoting Lavatory and Sink Carrier Systems

Table P2701.1, P2711.4, P2714.2

A112.19.14—2006 (R2011)

Six-Liter Water Closets Equipped with Dual Flushing Device

P2712.1

A112.19.15—2005

Bathtub/Whirlpool Bathtubs with Pressure-sealed Doors

Table P2701.1, P2713.2

A112.36.2m—1991 (R2008)

Cleanouts

P3005.2.10.2

B1.20.1—1983 (R2006)

Pipe Threads, General-purpose (Inch)

G2414.9, P3003.6.4, P3003.9.3

B16.3—2011

Malleable-iron-threaded Fittings, Classes 150 and 300

Table P2906.6

B16.4—2011

Gray-iron-threaded Fittings

Table P2906.6, Table P3002.3

B16.9—2007

Factory-made, Wrought-steel Buttwelding Fittings

Table P2906.6

B16.11—2011

Forged Fittings, Socket-welding and Threaded

Table P2906.6

B16.12—2009

Cast-iron-threaded Drainage Fittings

Table P3002.3

B16.15—2011

Cast-bronze-threaded Fittings

Table P2906.6, Table P3002.3

B16.18—2012

Cast-copper-alloy Solder Joint Pressure Fittings

Table P2906.6, Table P3002.3

B16.22—2001 (R2010)

Wrought-copper and Copper-alloy Solder Joint Pressure Fittings

Table P2906.6, Table P3002.3

B16.23—2002 (R2011)

Cast-copper-alloy Solder Joint Drainage Fittings (DWV)

Table P3002.3

B16.26—2011

Cast-copper-alloy Fittings for Flared Copper Tubes

Table P2906.6, Table P3002.3

B16.28—1994

Wrought-steel Buttwelding Short Radius Elbows and Returns

Table P2906.6

B16.29—2012

Wrought-copper and Wrought-copper-alloy Solder Joint Drainage Fittings (DWV)

Table P3002.3

B16.33—2012

Manually Operated Metallic Gas Valves for Use in Gas Piping Systems up to 125 psig (Sizes 1/2 through 2)

Table G2420.1.1

B16.34—2009

Valves—Flanged, Threaded and Welding End

Table P2903.9.4

B16.44—2002 (Reaffirmed 2007)

Manually Operated Metallic Gas Valves for Use in Above-ground Piping Systems up to 5 psi

Table G2420.1.1

B16.51—2011

Copper and Copper Alloy Press-Connect Pressure Fittings

Table 2906.6

B18.6.1—81(2016)

Wood Screws (inch Series)

R904.5.2

B36.10M—2004

Welded and Seamless Wrought-steel Pipe

G2414.4.2

BPVC—2010/2011 addenda

ASME Boiler and Pressure Vessel Code (2007 Edition)

M2001.1.1, G2452.1

CSD-1—2011

Controls and Safety Devices for Automatically Fired Boilers

M2001.1.1, G2452.1

ASSE 1016/ASME 112.1016/CSA B125.16—2011

Performance Requirements for Automatic Compensating Valves for Individual Showers and Tub/Shower Combinations

Table P2701.1, P2708.4, P2722.2

ASSE

American Society of Sanitary Engineering
901 Canterbury, Suite A
Westlake OH 44145
Standard
reference
number
TitleReferenced
in code
section number

1001—2008

Performance Requirements for Atmospheric-type Vacuum Breakers

Table P2902.3, P2902.3.2

1002—2008

Performance Requirements for Anti-siphon Fill Valves for Water Closet Flush Tank

Table P2701.1, Table P2902.3, P2902.4.1

1003—2009

Performance Requirements for Water-pressure-reducing Valves for Domestic Water Distribution Systems

P2903.3.1

1008—2006

Performance Requirements for Plumbing Aspects of Residential Food Waste Disposer Units

Table P2701.1

1010—2004

Performance Requirements for Water Hammer Arresters

P2903.5

1011—2004

Performance Requirements for Hose Connection Vacuum Breakers

Table P2902.3, P2902.3.2

1012—2009

Performance Requirements for Backflow Preventers with Intermediate Atmospheric Vent

Table P2902.3, P2902.3.3, P2902.5.1, P2902.5.5.3

1013—2009

Performance Requirements for Reduced Pressure Principle Backflow Preventers and Reduced Pressure Principle Fire Protection Backflow Preventers

Table P2902.3, P2902.3.5, P2902.5.1, P2902.5.5.3

1015—2009

Performance Requirements for Double Check Backflow Prevention Assemblies and Double Check Fire Protection Backflow Prevention Assemblies

Table P2902.3, P2902.3.6

ASSE 1016/ASME 112.1016/CSA B125.16—2011

Performance Requirements for Automatic Compensating Valves for Individual Showers and Tub/Shower Combinations

Table P2701.1, P2708.4, P2722.2

1017—2010

Performance Requirements for Temperature-actuated Mixing Valves for Hot Water Distribution Systems

P2724.1, P2802.1, P2803.2

1018—2010

Performance Requirements for Trap Seal Primer Valves; Potable Water Supplied

P3201.2.1

1019—2010

Performance Requirements for Freeze-resistant, Wall Hydrants, Vacuum Breaker, Draining Types

Table P2701.1, P2902.3.2

1020—2004

Performance Requirements for Pressure Vacuum Breaker Assembly

Table P2902.3, P2902.3.4

1023—2010

Performance Requirements for Hot Water Dispensers, Household-storage-type—Electrical

Table P2701.1

1024—2004

Performance Requirements for Dual Check Backflow Preventers, Anti-siphon-type, Residential Applications

Table P2902.3, P2902.3.7

1035—2008

Performance Requirements for Laboratory Faucet Backflow Preventers

Table P2902.3, P2902.3.2

1037—2010

Performance Requirements for Pressurized Flushing Devices (Flushometer) for Plumbing Fixtures

Table P2701.1

1044—2010

Performance Requirements for Trap Seal Primer Devices Drainage Types and Electronic Design Types

1047—2009

Performance Requirements for Reduced Pressure Detector Fire Protection Backflow Prevention Assemblies

Table P2902.3, P2902.3.5

1048—2009

Performance Requirements for Double Check Detector Fire Protection Backflow Prevention Assemblies

Table P2902.3, P2902.3.6

1050—2009

Performance Requirements for Stack Air Admittance Valves for Sanitary Drainage Systems

P3114.1

1051—2009

Performance Requirements for Individual and Branch-type Air Admittance Valves for Plumbing Drainage Systems

P3114.1

1052—2004

Performance Requirements for Hose Connection Backflow Preventers

Table P2701.1, Table P2902.3, P2902.3.2

1056—2010

Performance Requirements for Spill-resistant Vacuum Breakers

Table P2902.3, P2902.3.4

1060—2006

Performance Requirements for Outdoor Enclosures for Fluid-conveying Components

P2902.6.1

1061—2010

Performance Requirements for Removable and Nonremovable Push Fit Fittings

Table P2906.6

1062—2006

Performance Requirements for Temperature-actuated, Flow Reduction (TAFR) Valves for Individual Supply Fittings

Table P2701.1, P2724.2

1066—2009

Performance Requirements for Individual Pressure Balancing In-line Valves for Individual Fixture Fittings

P2722.4

1070—2004

Performance Requirements for Water-temperature-limiting Devices

P2713.3, P2721.2, P2724.1

1072—07

Performance Requirements for Barrier-type Floor Drain Trap Seal Protection Devices

ASTM

ASTM International
100 Barr Harbor Drive
West Conshohocken PA 19428
Standard
reference
number
TitleReferenced
in code
section number

A36/A36M—08

Specification for Carbon Structural Steel

R608.5.2.2

A53/A53M—12

Specification for Pipe, Steel, Black and Hot-dipped, Zinc-coated Welded and Seamless

R407.3, Table M2101.1, G2414.4.2, Table P2906.4, Table P2906.5, Table P3002.1(1)

A74—13A

Specification for Cast-iron Soil Pipe and Fittings

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3002.3, P3005.2.6, Table P3302.1

A90/A90M(2013)

Standard Test Method for Weight (Mass) of Coating on Iron and Steel Articles with Zinc or Zinc Alloy Coatings

R904.5.3

A106/A106M—11

Specification for Seamless Carbon Steel Pipe for High-temperature Service

Table M2101.1, G2414.4.2

A126—(2009)

Gray Iron Castings for Valves, Flanges and Pipe Fittings

Table P2903.9.4

A153/A153M—09

Specification for Zinc Coating (Hot Dip) on Iron and Steel Hardware

R317.3, Table R606.3.4.1, 703.6.3, R905.7.5, R905.8.6

A167—99 (2009)

Specification for Stainless and Heat-resisting Chromium-nickel Steel Plate, Sheet and Strip

Table R606.3.4.1

A240/A240M—2015b

Standard Specification for Chromium and Chromium-nickel Stainless Steel Plate, Sheet and Strip for Pressure Vessels and for General Applications

R904.5.3, Table R905.4.4

A254—97 (2007)

Specification for Copper Brazed Steel Tubing

Table M2101.1, G2414.5.1

A307—12

Specification for Carbon Steel Bolts and Studs, 60,000 psi Tensile Strength

R608.5.2.2

A312/A312M—13A

Specification for Seamless, Welded and Heavily Cold Worked Austenitic Stainless Steel Pipes

Table P2906.4, Table P2906.5, Table P2906.6

A463/A463M—10

Standard Specification for Steel Sheet, Aluminum-coated by the Hot-dip Process

Table R905.10.3(2)

A539—99

Specification for Electric-resistance-welded Coiled Steel Tubing for Gas and Fuel Oil Lines

M2202.1

A615/A615M—12

Specification for Deformed and Plain Billet-steel Bars for Concrete Reinforcement

R402.3.1, R404.1.3.3.7.1, R608.5.2.1

A641/A641M—14

Specification for Zinc-coated (Galvanized) Carbon Steel Wire

Table R606.3.4.1, R904.5.2

A653/A653M—11

Specification for Steel Sheet, Zinc-coated (Galvanized) or Zinc-iron Alloy-coated Galvanized) by the Hot-dip Process

R317.3.1, R505.2.2, R603.2.2, Table R606.3.4.1, R608.5.2.3, R804.2.2, R804.2.3, Table R905.4.4, M1601.1.1

A706/A706M—09B

Specification for Low-alloy Steel Deformed and Plain Bars for Concrete Reinforcement

R402.3.1, R404.1.3.3.7.1, R608.5.2.1

A755/A755M—2011

Specification for Steel Sheet, Metallic Coated by the Hot-dip Process and Prepainted by the Coil-coating Process for Exterior Exposed Building Products

Table R905.4.4

A778—01 (2009e1)

Specification for Welded Unannealed Austenitic Stainless Steel Tubular Products

A792/A792M—10

Specification for Steel Sheet, 55% Aluminum-zinc Alloy-coated by the Hot-dip Process

R505.2.2, R603.2.2, R608.5.2.3, R804.2.2, Table R905.4.4

A875/A875M—13

Specification for Steel Sheet, Zinc-5%, Aluminum Alloy-coated by the Hot-dip Process

R608.5.2.3, Table R905.10.3(2)

A888—13A

Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Application

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3002.3, Table P3302.1

A924/A924M—13

Standard Specification for General Requirements for Steel Sheet, Metallic-coated by the Hot-Dip Process

TableR905.4.4

A996/A996M—2009b

Specifications for Rail-steel and Axle-steel Deformed Bars for Concrete Reinforcement

Table R404.1.2(9), R402.3, R404.1.3.3.7.1, R608.5.2.1, Table R608.5.4(2)

A1003/A1003M—13A

Standard Specification for Steel Sheet, Carbon, Metallic and Nonmetallic-coated for Cold-formed Framing Members

R505.2.1, R505.2.2, R603.2.1, R603.2.2, R804.2.1

A1064/A1064M—16a

Carbon-Steel Wire and Welded Wire Reinforcement, Plain and Deformed, for Concrete

R506.2.4.2

B32—08

Specification for Solder Metal

P3003.6.3

B42—10

Specification for Seamless Copper Pipe, Standard Sizes

Table M2101.1, Table P2906.4, Table P2906.5, Table P3002.1(1)

B43—09

Specification for Seamless Red Brass Pipe, Standard Sizes

Table M2101.1, Table P2906.4, Table P2906.5, Table P3002.1(1)

B75—11

Specification for Seamless Copper Tube

Table M2101.1, Table P2906.5, Table P3002.1(1), Table P3002.1(2), Table P3002.2

B88—09

Specification for Seamless Copper Water Tube

Table M2101.1, G2414.5.2, Table P2906.4, Table P3002.1(1), Table P3002.1(2), Table P3002.2

B101—12

Specification for Lead-coated Copper Sheet and Strip for Building Construction

Table R905.4.4

B117—16

Standard Practice for Operating Salt Spray Apparatus (Fog)

R904.5.2

B135—10

Specification for Seamless Brass Tube

Table M2101.1

B209—10

Specification for Aluminum and Aluminum-alloy Sheet and Plate

Table R905.4.4

B227—10

Specification for Hard-drawn Copper-clad Steel Wire

B251—10

Specification for General Requirements for Wrought Seamless Copper and Copper-alloy Tube

Table M2101.1, Table P2906.4, Table P2906.5, Table P3002.1(1), Table P3002.1(2), Table P3002.2

B302—12

Specification for Threadless Copper Pipe, Standard Sizes

Table M2101.1, Table P2906.4, Table P2906.5, Table P3002.1(1)

B306—09

Specification for Copper Drainage Tube (DWV)

Table M2101.1, Table P3002.1(1), Table P3002.1(2)

B370—12

Specification for Copper Sheet and Strip for Building Construction

Table R905.4.4, Table R905.10.3(1), Table P2701.1

B447—12a

Specification for Welded Copper Tube

Table P2906.4, Table P2906.5

B695—04 (2009)

Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

R317.3.1, R317.3.3

B813—10

Specification for Liquid and Paste Fluxes for Soldering Applications of Copper and Copper Alloy Tube

Table M2101.1, M2103.3, P2906.14, P3003.6.3

B828—02 (2010)

Practice for Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings

M2103.3, P2906.14, P3003.6.3

C4—2009

Specification for Clay Drain Tile and Perforated Clay Drain Tile

Table P3302.1

C5—10

Specification for Quicklime for Structural Purposes

R702.2.1

C14—11

Specification for Non-reinforced Concrete Sewer, Storm Drain and Culvert Pipe

Table P3002.2

C22/C22M—00 (2010)

Specification for Gypsum

R702.2.1, R702.3.1

C27—98 (2008)

Specification for Standard Classification of Fireclay and High-alumina Refractory Brick

R1001.5

C28/C28M—10

Specification for Gypsum Plasters

R702.2.1

C33/C33M—13

Specification for Concrete Aggregates

R403.4.1

C34—12

Specification for Structural Clay Load-bearing Wall Tile

Table R301.2(1), R606.2.2

C35/C35M—1995 (2009)

Specification for Inorganic Aggregates for Use in Gypsum Plaster

R702.2.1

C55—2011

Specification for Concrete Building Brick

R202, Table R301.2(1), R606.2.1

C56—12

Standard Specification for Structural Clay Nonloadbearing Tile

R606.2.2

C59/C59M—00 (2011)

Specification for Gypsum Casting Plaster and Molding Plaster

R702.2.1

C61/C61M—00 (2011)

Specification for Gypsum Keene's Cement

R702.2.1

C62—13

Standard Specification for Building Brick (Solid Masonry Units Made from Clay or Shale)

R202, Table R301.2(1), R606.2.2

C73—10

Specification for Calcium Silicate Face Brick (Sand Lime Brick)

R202, Table R301.2(1), R606.2.1

C76—13A

Specification for Reinforced Concrete Culvert, Storm Drain and Sewer Pipe

Table P3002.2

C90—14

Specification for Load-bearing Concrete Masonry Units

Table R301.2(1), 606.2.1

C91—12

Specification for Masonry Cement

R702.2.2

C94/C94M—13

Standard Specification for Ready-mixed Concrete

R404.1.3.3.2, R608.5.1.2

C126—13

Standard Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units

R606.2.2

C129—11

Specification for Nonload-bearing Concrete Masonry Units

Table R301.2(1)

C143/C143M—12

Test Method for Slump of Hydraulic Cement Concrete

R404.1.3.3.4

C145—85

Specification for Solid Load-bearing Concrete Masonry Units

R202, Table R301.2(1)

C150—12

Specification for Portland Cement

R608.5.1.1, R702.2.2

C199—84 (2011)

Test Method for Pier Test for Refractory Mortar

R1001.5, R1001.8, R1003.12

C203—05a (2012)

Standard Test Methods for Breaking Load and Flexural Properties of Block-type Thermal Insulation

Table R610.3.1

C207—06 (2011)

Specification for Hydrated Lime for Masonry Purposes

Table R606.2.7

C208—12

Specification for Cellulosic Fiber Insulating Board

R602.1.10, Table R602.3(1), Table R906.2

C212-10

Standard Specification for Structural Clay Facing Tile

C216—13

Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)

R202, Table R301.2(1), R606.2.2

C270—12a

Specification for Mortar for Unit Masonry

R606.2.7, R606.2.10

C272/C272M—12

Standard Test Method for Water Absorption of Core Materials for Sandwich Constructions

Table R610.3.1

C273/C273M—11

Standard Test Method for Shear Properties of Sandwich Core Materials

Table R610.3.1

C315—07 (2011)

Specification for Clay Flue Liners and Chimney Pots

R1001.8, R1003.11.1, Table R1003.14(1), G2425.12

C406/C406M—2010

Specifications for Roofing Slate

R905.6.4

C411—11

Test Method for Hot-surface Performance of High-temperature Thermal Insulation

M1601.3

C425—04 (2009)

Specification for Compression Joints for Vitrified Clay Pipe and Fittings

Table P3002.2, P3003.10, P3003.13

C443—12

Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets

P3003.5, P3003.13

C475/C475—12

Specification for Joint Compound and Joint Tape for Finishing Gypsum Wallboard

R702.3.1

C476—10

Specification for Grout for Masonry

R606.2.11

C503—10

Standard Specification for Marble Dimension Stone

R606.2.4

C514—04 (2009)el

Specification for Nails for the Application of Gypsum Wallboard

R702.3.1

C552—12b

Standard Specification for Cellular Glass Thermal Insulation

Table R906.2

C557—03 (2009)e01

Specification for Adhesives for Fastening Gypsum Wallboard to Wood Framing

R702.3.1

C564—12

Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings

P3003.4.2, P3003.4.3, P3003.13

C568—10

Standard Specification for Limestone Dimension Stone

R606.2.4

C578—12b

Specification for Rigid, Cellular Polystyrene Thermal Insulation

R316.8, R403.3, R610.3.1, R703.11.2.1, Table R703.15.1, Table R703.15.2, Table R703.16.1, Table R703.16.2, Table R906.2

C587—04(2009)

Specification for Gypsum Veneer Plaster

R702.2.1

C595/C595M—13

Specification for Blended Hydraulic Cements

R608.5.1.1, R702.2.2

C615/C615M—11

Standard Specification for Granite Dimension Stone

R606.2.4

C616/C615M—10

Standard Specification for Quartz Dimension Stone

R606.2.4

C629—10

Standard Specification for Slate Dimension Stone

R606.2.4

C631—09

Specification for Bonding Compounds for Interior Gypsum Plastering

R702.2.1

C645—13

Specification for Nonstructural Steel Framing Members

R702.3.3

C652—13

Specification for Hollow Brick (Hollow Masonry Units Made from Clay or Shale)

R202, Table R301.2(1), R606.2.2

C685/C685M—11

Specification for Concrete Made by Volumetric Batching and Continuous Mixing

R404.1.3.3.2, R608.5.1.2

C700—13

Specification for Vitrified Clay Pipe, Extra Strength, Standard Strength and Perforated

Table P3002.2, Table P3002.3, Table P3302.1

C728—05 (2013)

Standard Specification for Perlite Thermal Insulation Board

Table R906.2

C744—11

Standard Specification for Prefaced Concrete and Calcium Silicate Masonry Units

R606.2.1

C836/C836M—12

Specification for High Solids Content, Cold Liquid-applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course

R905.15.2

C843—99 (2012)

Specification for Application of Gypsum Veneer Plaster

R702.2.1

C844—04 (2010)

Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster

R702.2.1

C847—12

Specification for Metal Lath

R702.2.1, R702.2.2

C887—05 (2010)

Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar

R406.1, R606.2.8

C897—05 (2009)

Specification for Aggregate for Job-mixed Portland Cement-based Plasters

R702.2.2

C920—11

Standard Specification for Elastomeric Joint Sealants

R406.4.1, R703.4

C926—15b

Specification for Application of Portland Cement-based Plaster

R202, R702.2.2, R702.2.2.1, R703.7, R703.7.2.1, R703.7.4

C933—13

Specification for Welded Wire Lath

R702.2.1, R702.2.2

C946—10

Standard Practice for Construction of Dry-Stacked, Surface-Bonded Walls

R606.2.8

C954—11

Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 in (0.84 mm) or to 0.112 in. (2.84 mm) in Thickness

R505.2.5, R603.2.5, R702.3.5.1, R804.2.5

C955—11C

Specification for Load-bearing (Transverse and Axial) Steel Studs, Runners (Tracks), and Bracing or Bridging for Screw Application of Gypsum Panel Products and Metal Plaster Bases

R702.3.3

C957—10

Specification for High-solids Content, Cold Liquid-applied Elastomeric Waterproofing Membrane for Use with Integral Wearing Surface

R905.15.2

C1002—07

Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases

R702.3.1, R702.3.5.1

C1029—13

Specification for Spray-applied Rigid Cellular Polyurethane Thermal Insulation

R905.14.2

C1032—06 (2011)

Specification for Woven Wire Plaster Base

R702.2.1, R702.2.2

C1047—10a

Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base

R702.2.1, R702.2.2, R702.3.1

C1063—15a

Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-based Plaster

R702.2.2, R703.7

C1088—13

Standard Specification for Thin Veneer Brick Units Made from Clay or Shale

R606.2.2

C1107/C1107M—13

Standard Specification for Packaged Dry, Hydraulic-cement Grout (Nonshrink)

R402.3.1

C1116/C116M—10a (Reapprove 2015)

Standard Specification for Fiber-reinforced Concrete and Shotcrete

R506.2.4.2

C1157—11/C1157M—11

Standard Performance Specification for Hydraulic Cement

R608.5.1.1

C1167—11

Specification for Clay Roof Tiles

R905.3.4

C1173—10e1

Specification for Flexible Transition Couplings for Underground Piping Systems

P3003.3.1, P3003.5, P3003.6.1, P3003.12.1, P3003.12.2, P3003.13

C1177/C1177M—08

Specification for Glass Mat Gypsum Substrate for Use as Sheathing

R702.3.1, Table 906.2

C1178/C1178M—11

Specification for Glass Mat Water-resistant Gypsum Backing Panel

R702.3.1, R702.3.7, Table R702.4.2

C1186—08 (2012)

Specification for Flat Nonasbestos Fiber Cement Sheets

R703.10.1, R703.10.2

C1261—10

Specification for Firebox Brick for Residential Fireplaces

R1001.5, R1001.8

C1277—12

Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings

P3003.4.3

C1278/C1278M—07a (2011)

Specification for Fiber-reinforced Gypsum Panels

R702.3.1, R702.3.7, Table R702.4.2, Table R906.2

C1281—14

Standard Specification for Preformed Tape Sealants

R703.4

C1283—11

Practice for Installing Clay Flue Lining

R1003.9.1, R1003.12

C1288—99 (2010)

Standard Specification for Discrete Nonasbestos Fiber-cement Interior Substrate Sheets

Table R503.2.1.1(1), Table R503.2.1.1(2), Table 602.3(2), Table R702.4.2

C1289—13e1

Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board

R316.8, R703.11.2.1, Table R703.15.1, Table R703.15.2, Table R703.16.1, Table R703.16.2, Table R906.2

C1325—08b

Standard Specification for Nonasbestos Fiber-mat Reinforced Cement Interior Substrate Sheets Backer Units

Table R702.4.2

C1328/C1328M—12

Specification for Plastic (Stucco) Cement

R702.2.2

C1364—10B

Standard Specification for Architectural Cast Stone

R606.2.5

C1386—07

Standard Specification for Precast Autoclaved Aerated Concrete (AAC) Wall Construction Units

R606.2.3

C1396/C1396M—2013

Specification for Gypsum Board

Table R602.3(1), R702.2.1, R702.2.2, R702.3.1, R702.3.7

C1405—12

Standard Specification for Glazed Brick (Single Fired, Brick Units)

R606.2.2

C1440—08

Specification for Thermoplastic Elastomeric (TPE) Gasket Materials for Drain, Waste and Vent (DWV), Sewer, Sanitary and Storm Plumbing Systems

P3003.13

C1460—08

Specification for Shielded Transition Couplings for Use with Dissimilar DWV Pipe and Fittings Above Ground

C1461—08

Specification for Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste and Vent (DWV) Sewer, Sanitary and Storm Plumbing Systems for Above and Below Ground Use

P3003.13

C1492—03 (2009)

Specification for Concrete Roof Tile

R905.3.5

C1513—2013

Standard Specification for Steel Tapping Screws for Cold-formed Steel Framing Connections

R505.2.5, R603.2.5, Table R703.3(2), R804.2.5, Table R703.16.1, Table R703.16.2

C1540—11

Specification for Heavy Duty Shielded Couplings Joining Hubless Cast-iron Soil Pipe and Fittings

P3003.4.3

C1634—11

Standard Specification for Concrete Facing Brick

R606.2.1

C1658/C1658M—12

Standard Specification for Glass Mat Gypsum Panels

R702.3.1

C1668—12

Standard Specification for Externally Applied Reflective Insulation Systems on Rigid Duct in Heating, Ventilation, and Air Conditioning (HVAC) Systems

M1601.3

D41—05

Specification for Asphalt Primer Used in Roofing, Dampproofing and Waterproofing

Table R905.9.2, Table R905.11.2

D43—00 (2006)

Specification for Coal Tar Primer Used in Roofing, Dampproofing and Waterproofing

Table R905.9.2

D226/D226M—09

Specification for Asphalt-saturated (Organic Felt) Used in Roofing and Waterproofing

R703.2, R905.1.1, Table R905.1.1, Table R905.9.2

D227/D227M—03 (2011)e1

Specification for Coal Tar Saturated (Organic Felt) Used in Roofing and Waterproofing

Table R905.9.2

D312—00 (2006)

Specification for Asphalt Used in Roofing

Table R905.9.2

D422—63 (2007)

Test Method for Particle-size Analysis of Soils

R403.1.8.1

D449—03 (2008)

Specification for Asphalt Used in Dampproofing and Waterproofing

R406.2

D450—07

Specification for Coal-tar Pitch Used in Roofing, Dampproofing and Waterproofing

Table R905.9.2

D1227—95 (2007)

Specification for Emulsified Asphalt Used as a Protective Coating for Roofing

Table R905.9.2, Table R905.11.2, R905.15.2

D1248—12

Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable

M1601.1.2

D1527—99 (2005)

Specification for Acrylonitrile-butadiene-styrene (ABS) Plastic Pipe, Schedules 40 and 80

Table P2906.4

D1621—10

Standard Test Method for Compressive Properties of Rigid Cellular Plastics

Table R610.3.1

D1622—08

Standard Test Method for Apparent Density of Rigid Cellular Plastics

Table R610.3.1

D1623—09

Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics

Table R610.3.1

D1693—2013

Test Method for Environmental Stress-cracking of Ethylene Plastics

Table M2101.1

D1784—11

Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Compounds and Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds

M1601.1.2

D1785—12

Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80 and 120

Table P2906.4, Table AG101.1

D1863/D1863M—05 (2011)e1

Specification for Mineral Aggregate Used in Built-up Roofs

Table R905.9.2

D1869—95 (2010)

Specification for Rubber Rings for Asbestos-cement Pipe

P2906.17, P3003.13

D1970/D1970M—2015

Specification for Self-adhering Polymer Modified Bitumen Sheet Materials Used as Steep Roofing Underlayment for Ice Dam Protection

R905.1.1, Table R905.1.1, R905.2.8.2

D2104—03

Specification for Polyethylene (PE) Plastic Pipe, Schedule 40

D2126—09

Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging

Table R610.3.1

D2178—04

Specification for Asphalt Glass Felt Used in Roofing and Waterproofing

Table R905.9.2

D2235—04 (2011)

Specification for Solvent Cement for Acrylonitrile-butadiene-styrene (ABS) Plastic Pipe and Fittings

P2906.9.1.1, P3003.3.2

D2239—12A

Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter

Table P2906.4, Table AG101.1

D2241—09

Specification for Poly (Vinyl Chloride) (PVC) Pressure-rated Pipe (SDR-Series)

Table AG101.1

D2282—99 (2005)

Specification for Acrylonitrile-butadiene-styrene (ABS) Plastic Pipe (SDR-PR)

D2412—11

Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-plate Loading

M1601.1.2

D2447—03

Specification for Polyethylene (PE) Plastic Pipe Schedules 40 and 80, Based on Outside Diameter

Table M2101.1

D2464—06

Specification for Threaded Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

Table P2906.6

D2466—06

Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40

Table P2906.6

D2467—06

Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

Table P2906.6

D2468—96a

Specification for Acrylonitrile-butadiene-styrene (ABS) Plastic Pipe Fittings, Schedule 40

Table P2906.6

D2513—2013e1

Specification for Thermoplastic Gas Pressure Pipe, Tubing and Fittings

Table M2101.1, G2414.6, G2414.6.1, G2414.11, G2415.17.2

D2559—12A

Standard Specification for Adhesives for Bonded Structural Wood Products for Use Under Exterior (West Use) Exposure Conditions

R610.3.3

D2564—12

Specification for Solvent Cements for Poly (Vinyl Chloride) (PVC) Plastic Piping Systems

P2906.9.1.4, P3003.8.2, P3003.9.2

D2609—02 (2008)

Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe

Table P2906.6

D2626/D2626M—04 (2012)e1

Specification for Asphalt-saturated and Coated Organic Felt Base Sheet Used in Roofing

R905.3.3, Table R905.9.2

D2657—07

Standard Practice for Heat Fusion-joining of Polyolefin Pipe Fittings

M2105.11.1, P2906.3.1, P3003.12.1

D2661—11

Specification for Acrylonitrile-butadiene-styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3002.3, P3003.3.2

D2665—12

Specification for Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste and Vent Pipe and Fittings

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3002.3, Table AG101.1

D2672—96a (2009)

Specification for Joints for IPS PVC Pipe Using Solvent Cement

Table P2906.4

D2683—2010e1

Specification for Socket-type Polyethylene Fittings for Outside Diameter-controlled Polyethylene Pipe and Tubing

Table M2105.5, M2105.11.1, P3010.5

D2729—11

Specification for Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings

P3009.11, Table P3302.1, Table AG101.1

D2737—2012A

Specification for Polyethylene (PE) Plastic Tubing

Table P2906.4, Table AG101.1

D2751—05

Specification for Acrylonitrile-butadiene-styrene (ABS) Sewer Pipe and Fittings

Table P3002.2, Table P3002.3

D2822/D2822M—05 (2011)e1

Specification for Asphalt Roof Cement, Asbestos Containing

Table R905.9.2

D2823/D2823—05 (2011)e1

Specification for Asphalt Roof Coatings, Asbestos Containing

Table R905.9.2

D2824—06 (2012)e1

Specification for Aluminum-pigmented Asphalt Roof Coatings, Nonfibered, Asbestos Fibered and Fibered without Asbestos

Table R905.9.2, Table R905.11.2

D2846/D2846M—09BE1

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Hot- and Cold-water Distribution Systems

Table M2101.1, Table P2906.4, Table P2906.5, Table P2906.6, P2906.9.1.2, P2906.9.1.3, Table AG101.1

D2855—96 (2010)

Standard Practice for Making Solvent-cemented Joints with Poly (Vinyl Chloride) (PVC) Pipe and Fittings

P3003.9.2

D2898—10

Test Methods for Accelerated Weathering of Fire-retardant-treated Wood for Fire Testing

R802.1.5.4, R802.1.5.8

D2949—10

Specification for 3.25-in. Outside Diameter Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste and Vent Pipe and Fittings

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3002.3, Table AG101.1

D3019—08

Specification for Lap Cement Used with Asphalt Roll Roofing, Nonfibered, Asbestos Fibered and Nonasbestos Fibered

Table R905.9.2, Table R905.11.2

D3034—08

Specification for Type PSM Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings

Table P3002.2, Table P3002.3, Table AG101.1

D3035—2012e1

Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based On Controlled Outside Diameter

Table M2105.4, Table AG101.1

D3161/D3161M—2016

Test Method for Wind Resistance of Asphalt Shingles (Fan Induced Method)

R905.2.6.1, R905.16.7

D3201—2013

Test Method for Hygroscopic Properties of Fire-retardant Wood and Wood-base Products

R802.1.5.9

D3212—07

Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals

P3003.3.1, P3003.9.1, P3003.12.2

D3261—12

Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing

Table M2105.5, M2105.11.1

D3309—96a (2002)

Specification for Polybutylene (PB) Plastic Hot- and Cold-water Distribution System

Table M2101.1

D3311—11

Specification for Drain, Waste and Vent (DWV) Plastic Fittings Patterns

P3002.3

D3350—2012e1

Specification for Polyethylene Plastic Pipe and Fitting Materials

Table M2101.1

D3462/D3462M—10A

Specification for Asphalt Shingles Made From Glass Felt and Surfaced with Mineral Granules

R905.2.4

D3468—99 (2006)e01

Specification for Liquid-applied Neoprene and Chlorosulfanated Polyethylene Used in Roofing and Waterproofing

R905.15.2

D3679—11

Specification for Rigid Poly (Vinyl Chloride) (PVC) Siding

R703.11

D3737—2012

Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)

R502.1.3, R602.1.3, R802.1.2

D3747—79 (2007)

Specification for Emulsified Asphalt Adhesive for Adhering Roof Insulation

Table R905.9.2, Table R905.11.2

D3787—01

Testing Method for Bursting Strength of Textiles, Constant-Rate-of-Traverse (CRT) Ball Burst Test

R4501.17.1.15

D3909/D3909M—97b (2012)e1

Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules

R905.2.8.2, R905.5.4, Table R905.9.2

D4022/D4022M—2007 (2012)e1

Specification for Coal Tar Roof Cement, Asbestos Containing

Table R905.9.2

D4068—09

Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water Containment Membrane

P2709.2, P2709.2.2

D4318—10

Test Methods for Liquid Limit, Plastic Limit and Plasticity Index of Soils

R403.1.8.1

D4434/D4434M—12

Specification for Poly (Vinyl Chloride) Sheet Roofing

R905.13.2

D4479/D4479M—07 (2012)e1

Specification for Asphalt Roof Coatings-asbestos-free

Table R905.9.2

D4533—15

Standard Test Method for Trapezoid Tearing Strength of Geotextiles

R905.1.1

D4551—12

Specification for Poly (Vinyl) Chloride (PVC) Plastic Flexible Concealed Water-containment Membrane

P2709.2, P2709.2.1

D4586/D4586M—07 (2012)e1

Specification for Asphalt Roof Cement-asbestos-free

Table R905.9.2

D4601/D4601M—04 (2012)e1

Specification for Asphalt-coated Glass Fiber Base Sheet Used in Roofing

Table R905.9.2

D4637/D4637M—2013

Specification for EPDM Sheet Used in Single-ply Roof Membrane

R905.12.2

D4829—11

Test Method for Expansion Index of Soils

R403.1.8.1

D4869/D4869M(2016)

Specification for Asphalt-saturated (Organic Felt) Underlayment Used in Steep Slope Roofing

R905.1.1, Table R905.1.1

D4897/D4897M—01 (2009)

Specification for Asphalt Coated Glass-fiber Venting Base Sheet Used in Roofing

Table R905.9.2

D4990—97a (2005)e01

Specification for Coal Tar Glass Felt Used in Roofing and Waterproofing

Table R905.9.2

D5019—07a

Specification for Reinforced Nonvulcanized Polymeric Sheet Used in Roofing Membrane

R905.12.2

D5034—95

Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) Specifications for Adhesives for Field Gluing Plywood to Lumber Framing for Floor Systems

R4501.17.1.15

D5055—2013

Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-joists

R502.1.2

D5456—2013

Standard Specification for Evaluation of Structural Composite Lumber Products

R502.1.5, R602.1.5, R802.1.7

D5516—09

Test Method for Evaluating the Flexural Properties of Fire-retardant-treated Softwood Plywood Exposed to the Elevated Temperatures

R802.1.5.7

D5643/D5643M—06 (2012)e1

Specification for Coal Tar Roof Cement Asbestos-free

Table R905.9.2

D5664—10

Test Methods For Evaluating the Effects of Fire-retardant Treatments and Elevated Temperatures on Strength Properties of Fire-retardant-treated Lumber

R802.1.5.7

D5665—99a (2006)

Specification for Thermoplastic Fabrics Used in Cold-applied Roofing and Waterproofing

Table R905.9.2

D5726—98 (2005)

Specification for Thermoplastic Fabrics Used in Hot-applied Roofing and Waterproofing

Table R905.9.2

D6083—05e01

Specification for Liquid-applied Acrylic Coating Used in Roofing

Table R905.9.2, Table R905.11.2, Table R905.14.3, R905.15.2

D6162—2000a (2008)

Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements

Table R905.11.2

D6163—00 (2008)

Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements

Table R905.11.2

D6164/D6164M—11

Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Polyester Reinforcements

Table R905.11.2

D6222/D6222M—11

Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements

Table R905.11.2

D6223/D6223M—02 (2011)e1

Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcement

Table R905.11.2

D6298—05e1

Specification for Fiberglass-reinforced Styrene Butadiene Styrene (SBS) Modified Bituminous Sheets with a Factory Applied Metal Surface

Table R905.11.2

D6305—08

Practice for Calculating Bending Strength Design Adjustment Factors for Fire-retardant-treated Plywood Roof Sheathing

R802.1.5.6

D6380—03 (2013)

Standard Specification for Asphalt Roll Roofing (Organic Felt)

Table R905.1.1(1), R905.2.8.2, R905.5.4

D6509/D6509M—16

Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Base Steel Materials Using Glass Fiber Reinforcements

Table R905.11.2

D6694—08

Standard Specification for Liquid-applied Silicone Coating Used in Spray Polyurethane Foam Roofing Systems

Table R905.14.3, R905.15.2

D6754/D6745M—10

Standard Specification for Ketone-ethylene-ester-based Sheet Roofing

R905.13.2

D6757—2016

Standard Specification for Inorganic Underlayment for Use with Steep Slope Roofing Products

Table R905.1.1, R905.1.1

D6841—08

Standard Practice for Calculating Design Value Treatment Adjustment Factors for Fire-retardant-treated Lumber

R802.1.5.7

D6878/D6878—11a

Standard Specification for Thermoplastic-polyolefin-based Sheet Roofing

R905.13.2

D6947—07

Standard Specification for Liquid Applied Moisture Cured Polyurethane Coating Used in Spray Polyurethane Foam Roofing System

Table R905.14.3, R905.15.2

D7032—10a

Standard Specification for Establishing Performance Ratings for Wood-plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails)

R507.3, R507.3.1, 507.3.4, 507.3.4

D7158/D7158M—2011

Standard Test Method for Wind Resistance of Sealed Asphalt Shingles (Uplift Force/Uplift Resistance Method)

R905.2.6.1

D7254—07

Standard Specification for Polypropylene (PP) siding

Table R703.3(1), R703.14

D7425/D7425M—11

Standard Specification for Spray Polyurethane Foam Used for Roofing Application

R905.14.2

D7672—2012

Standard Specification for Evaluating Structural Capacities of Rim Board Products and Assemblies

R502.1.7, R602.1.7, R802.1.7

D7793—13

Standard Specification for Insulated Vinyl Siding

R703.13, Table R703.3(1)

E84—2013a

Test Method for Surface Burning Characteristics of Building Materials

R202, R302.9.3, R302.9.4, R302.10.1, R302.10.2, R316.3, R316.5.9, R316.5.11, R507.3.2, R802.1.5, M1601.3, M1601.5.2

E96/E96M—2013

Test Method for Water Vapor Transmission of Materials

R202, Table R610.3.1, M1411.6, M1601.4.6

E108—2011

Test Methods for Fire Tests of Roof Coverings

R302.2.2, R902.1

E119—2012a

Test Methods for Fire Tests of Building Construction and Materials

Table R302.1(1), Table R302.1(2), R302.2, R302.2.2, R302.3, R302.4.1, R302.11.1

E136—2012

Test Method for Behavior of Materials in a Vertical Tube Furnace at 750°C

R202, R302.11

E330—02 or 14

Test Method for Structural Performance of Exterior Windows, Curtain Walls and Doors by Uniform Static Air Pressure Difference

R609.4, R609.5, R703.1.2

E331—00 (2009)

Test Method for Water Penetration of Exterior Windows, Skylights, Doors and Curtain Walls by Uniform Static Air Pressure Difference

R703.1.1

E814—2013

Test Method for Fire Tests of Through-penetration Firestops

R302.4.1.2

E970—2010

Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source

R302.10.5

E1300—04e01, 07e01, 09e or 12AE1

Practice for Determining Load Resistance of Glass in Buildings

R609.3

E1509—12

Standard Specification for Room Heaters, Pellet Fuel-burning Type

M1410.1

E1602—03 (2010)e1

Guide for Construction of Solid Fuel Burning Masonry Heaters

R1002.2

E1886—02 or 05 or 2013a

Test Method for Performance of Exterior Windows, Curtain Walls, Doors and Storm Shutters Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials

R301.2.1.2, R609.3.1, R609.6.1, Table R703.11.2

E1996—02, 05, 06, 09 or 2012a or 2014a

Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes

R301.2.1.2, R301.2.1.2.1, R609.3.1, R609.6.1

E2178—2013

Standard Test Method for Air Permeance of Building Materials

R202

E2231—09

Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics

M1601.3

E2273—03 (2011)

Standard Test Method for Determining the Drainage Efficiency of Exterior Insulation and Finish Systems (EIFS) Clad Wall Assemblies

R703.9.2

E2568—09e1

Standard Specification for PB Exterior Insulation and Finish Systems

R703.9.1, R703.9.2

E2570—07

Standard Test Methods for Evaluating Water-resistive Barrier (WRB) Coatings Used Under Exterior Insulation and Finish Systems (EIFS) or EIFS with Drainage

R703.9.2

E2634—11

Standard Specification for Flat Wall Insulating Concrete Form (ICF) Systems

R404.1.3.3.6.1, R608.4.4

F405—05

Specification for Corrugated Polyethylene (PE) Pipe and Fittings

Table P3009.11, Table P3302.1, Table AG101.1

F409—12

Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings

Table P2701.1, P2702.2, P2702.3

F437—09

Specification for Threaded Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

Table P2906.6

F438—09

Specification for Socket-type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40

Table P2906.6

F439—12

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

Table P2906.6

F441/F441M—13

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80

Table P2906.4, Table P2906.5, Table AG101.1

F442/F442M—13

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR)

Table P2906.4, Table P2906.5, Table AG101.1

F477—10

Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe

P2906.17, P3003.13

F493—10

Specification for Solvent Cements for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe and Fittings

P2906.9.1.2, P2906.9.1.3

F628—08

Specification for Acrylonitrile-butadiene-styrene (ABS) Schedule 40 Plastic Drain, Waste and Vent Pipe with a Cellular Core

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3002.3, P3003.3.2, Table AG101.1

F656—10

Specification for Primers for Use in Solvent Cement Joints of Poly (Vinyl Chloride) (PVC) Plastic Pipe and Fittings

P2906.9.1.4, P3003.9.2

F714—13

Specification for Polyethylene (PE) Plastic Pipe (SDR-PR) Based on Outside Diameter

Table P3002.2, P3010.4

F876—13

Specification for Cross-linked Polyethylene (PEX) Tubing

Table M2101.1, Table P2906.4, Table P2906.5, Table AG101.1

F877—11A

Specification for Cross-linked Polyethylene (PEX) Plastic Hot- and Cold-water Distribution Systems

Table M2101.1, Table P2906.4, Table P2906.5, Table P2906.6

F891—10

Specification for Coextruded Poly (Vinyl Chloride) (PVC) Plastic Pipe with a Cellular Core

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3302.1, Table AG101.1

F1055—13

Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene Pipe and Tubing

Table M2105.5, M2105.11.2

F1281—11

Specification for Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Pressure Pipe

Table M2101.1, Table P2906.4, Table P2906.5, Table P2906.6, Table AG101.1

F1282—10

Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe

Table M2101.1, Table P2906.4, Table P2906.5, Table P2906.6, P2906.11.1, Table AG101.1

F1346—91 (2003)

Performance Specification for Safety Covers and Labeling Requirements for All Covers for Swimming Pools, Spas and Hot Tubs

R4501.3, R4501.17

F1412—09

Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage

Table P3002.1(2), Table P3002.2, Table P3002.3, P3003.11.1

F1488—09e1

Specification for Coextruded Composite Pipe

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3009.11

F1554—07a

Specification for Anchor Bolts, Steel, 36, 55 and 105-ksi Yield Strength

R608.5.2.2

F1667—15

Specification for Driven Fasteners, Nails, Spikes and Staples

R317.3, R703.3.2, R703.6.3, Table R703.15.1, Table R703.15.2, R803.2.3.1, R904.5.1, R905.2.5, R908.7.1.1

F1807—13

Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

Table M2101.1, Table P2906.6

F1866—07

Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings

Table P3002.3

F1924—12

Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing

M2105.11.1

F1960—12

Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) Tubing

Table M2101.1, Table P2906.6

F1970—12

Standard Specification for Special Engineered Fittings, Appurtenances or Valves for Use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems

M2105.5, Table 2903.9.4

F1973—08

Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA 11) Fuel Gas Distribution Systems

F1974—09

Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene Composite Pressure Pipe

Table P2906.6

F1986—01 (2011)

Multilayer Pipe Type 2, Compression Joints for Hot and Cold Drinking Water Systems

Table P2906.4, Table P2906.5, Table P2906.6

F2080—12

Specification for Cold-expansion Fittings with Metal Compression-sleeves for Cross-linked Polyethylene (PEX) Pipe

P2906.6

F2090—10

Specification for Window Fall Prevention Devices—with Emergency Escape (Egress) Release Mechanisms

R310.1.1, R312.2.1, R312.2.2

F2098—08

Standard Specification for Stainless Steel Clamps for Securing SDR9 Cross-linked Polyethylene (PEX) Tubing to Metal Insert and Plastic Insert Fittings

Table M2101.1, Table P2906.6

F2159—11

Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

Table P2906.6

F2208—2014

Standard Safety Specification for Residential Pool Alarms

R4501.17.1.9

F2262—09

Standard Specification for Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene Tubing OD Controlled SDR9

Table P2906.4, Table P2906.5

F2389—10

Standard for Pressure-rated Polypropylene (PP) Piping Systems

Table P2906.4, Table P2906.5, Table P2906.6, P2906.10.1, Table AG101.1

F2434—09

Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Tubing

Table P2906.6

F2623—08

Standard Specification for Polyethylene of Raised Temperature (PE-RT) SDRG Tubing

Table M2101.1, Table AG101.1

F2735—09

Standard Specification for Plastic Insert Fittings for SDR9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing

Table M2101.1, Table P2906.6

F2769—10

Polyethylene or Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems

Table M2101.1, Table P2906.4, Table P2906.5, Table P2906.6, Table AG101.1

F2806—10

Standard Specification for Acrylonitrile-butadiene-styrene (ABS) Plastic Pipe (Metric SDR-PR)

Table M2101.1

F2855—12

Standard Specification for Chlorinated Poly (Vinyl Chloride)/ Aluminum/Chlorinated Poly (Vinyl Chloride) (CPVC AL CPVC) Composite Pressure Tubing

Table P2906.4, Table P2906.5, Table AG101.1

F2969—12

Standard Specification for Acrylonitrile-butadiene-styrene (ABS) IPS Dimensioned Pressure Pipe

Table M2101.1

G53—96

Practice for Operating Light- and Water-Exposure Apparatus (Fluorescent UV-Condensation Type) for Exposure of Nonmetallic Materials

R4501.17.1.15

AWC

American Wood Council
222 Catocin Circle, Suite 201
Leesburg VA 20175
Standard
reference
number
TitleReferenced
in code
section number

AWC STJR—2015

Span Tables for Joists and Rafters

R502.3, R802.4, R802.5

AWC WFCM—2015

Wood Frame Construction Manual for One- and Two-family Dwellings

R301.1.1, R301.2.1.1R602.10.8.2R608.9.2Figure R608.9(9)R608.10

ANSI AWC NDS—2015

National Design Specification (NDS) for Wood Construction— with 2015 NDS Supplement

R404.2.2, R502.2, Table R503.1, R602.3, R608.9.2, Table R703.15.1, Table R703.15.2, R802.2

ANSI/AWC PWF—2015

Permanent Wood Foundation Design Specification

R317.3.2, R401.1, R404.2.3

AWPA

American Wood Protection Association
P.O. Box 361784
Birmingham AL 35236-1784
Standard
reference
number
TitleReferenced
in code
section number

C1—03

All Timber Products—Preservative Treatment by Pressure Processes

R902.2

M4—11

Standard for the Care of Preservative-treated Wood Products

R317.1.1, R318.1.2

U1—14

USE CATEGORY SYSTEM: User Specification for Treated Wood Except Section 6 Commodity Specification H

R317.1, R402.1.2, R504.3, R703.6.3, R905.7.5, Table R905.8.5, R905.8.6

AWS

American Welding Society
8669 NW 36 Street, #130
Doral FL 33166
Standard
reference
number
TitleReferenced
in code
section number

A5.8M/A5.8—2011

Specifications for Filler Metals for Brazing and Braze Welding

P3003.6.1

ANSI/AWS A5.31M/A5.31—2012

Specification for Fluxes for Brazing and Braze Welding Edition: 2nd

M2103.3, M2202.2, P2906.14, M2103.3

AWWA

American Water Works Association
6666 West Quincy Avenue
Denver CO 80235
Standard
reference
number
TitleReferenced
in code
section number

C104/A21.4—08

Cement-mortar Lining for Ductile-iron Pipe and Fittings for Water

P2906.4

C110/A21.10—12

Ductile-iron and Gray-iron Fittings

Table P2906.6,

C115/A21.15—11

Flanged Ductile-iron Pipe with Ductile-iron or Gray-iron Threaded Flanges

Table P2906.4

C151/A21.51—09

Ductile-iron Pipe, Centrifugally Cast, for Water

Table P2906.4

C153/A21.53—11

Ductile-iron Compact Fittings for Water Service

Table P2906.6

C500—09

Standard for Metal-seated Gate Valves for Water Supply Service

Table P2903.9.4

C504—10

Standard for Rubber-seated Butterfly Valves

Table P2903.9.4

C507—11

Standard for Ball Valves, 6 In. Through 60 In.

Table P2903.9.4

C510—07

Double Check Valve Backflow Prevention Assembly

Table P2902.3, P2902.3.6

C511—07

Reduced-pressure Principle Backflow Prevention Assembly

Table P2902.3, P2902.3.5, P2902.5.1

C901—08

Polyethylene (PE) Pressure Pipe and Tubing 1/2 in. (13 mm) through 3 in. (76 mm) for Water Service

P2906.4, Table AG101.1

C903—05

Polyethylene-aluminum-polyethylene & Crosslinked Polyethylene Composite Pressure Pipe, 1/2 in. (12 mm) through 2 in. (50 mm), for Water Service

C904—06

Cross-linked Polyethylene (PEX) Pressure Pipe, 1/2 in. (12 mm) through 3 in. (76 mm) for Water Service

P2906.4, Table AG101.1

CEN

European Committee for Standardization (EN)
Central Secretariat
Rue de Stassart 36
Brussels B-10 50
Standard
reference
number
TitleReferenced
in code
section number

EN 15250-2007

Slow Heat Release Appliances Fired by Solid Fuel Requirements and Test Methods

R1002.5

CGSB

Canadian General Standards Board
Place du Portage 111, 6B1
11 Laurier Street
Gatineau Quebec, Canada KIA 1G6
Standard
reference
number
TitleReferenced
in code
section number

CAN/CGSB-37.54—95

Polyvinyl Chloride Roofing and Waterproofing Membrane

R905.13.2

37-GP-52M—(1984)

Roofing and Waterproofing Membrane, Sheet Applied, Elastomeric

R905.12.2

37-GP-56M—(1980)

Membrane, Modified Bituminous, Prefabricated and Reinforced for Roofing—with December 1985 Amendment

Table R905.11.2

CISPI

Cast Iron Soil Pipe Institute
5959 Shallowford Road, Suite 419
Chattanooga TN 37421
Standard
reference
number
TitleReferenced
in code
section number

301—04a

Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Applications

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3002.3, Table P3302.1

310—04

Standard Specification for Coupling for Use in Connection with Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Applications

P3003.4.3

CPA

Composite Panel Association
19465 Deerfield Avenue, Suite 306
Leesburg VA 20176
Standard
reference
number
TitleReferenced
in code
section number

ANSI A135.4—2012

Basic Hardboard

Table R602.3(2)

ANSI A135.5—2012

Prefinished Hardboard Paneling

R702.5

ANSI A135.6—2012

Engineered Wood Siding

R703.5

ANSI A135.7—2012

Engineered Wood Trim

R703.5

A208.1—2009

Particleboard

R503.3.1, R602.1.9, R605.1

CPSC

Consumer Product Safety Commission
4330 East West Highway
Bethesda MD 20814-4408
Standard
reference
number
TitleReferenced
in code
section number

16 CFR, Part 1201—(2002)

Safety Standard for Architectural Glazing

R308.1.1, R308.3.1, Table R308.3.1(1)

16 CFR, Part 1209—(2002)

Interim Safety Standard for Cellulose Insulation

R302.10.3

16 CFR, Part 1404—(2002)

Cellulose Insulation

R302.10.3

CSA

CSA Group
8501 East Pleasant Valley Road
Cleveland OH 44131-5516
Standard
reference
number
TitleReferenced
in code
section number

AAMA/WDMA/CSA 101/I.S.2/A440—11

North American Fenestration Standard/Specification for Windows, Doors and Unit Skylights

R308.6.9, R609.3

ANSI/CSA America

Stationary Fuel Cell Power Systems

M1903.1

FCI—2012 ASME A112.3.4—2013/CSA B45.9—13

Macerating Toilet Systems and Related Components

Table P2701.1, P3007.5

ASME A112.18.2—2011/CSA B125.2—2011

Plumbing Waste Fittings

Table P2701.1, P2702.2

A112.18.6/CSA B125.6—2009

Flexible Water Connectors

P2906.7

ASME A112.19.1—2013/CSA B45.2—13

Enameled Cast-iron and Enameled Steel Plumbing Fixtures

Table 2701.1, P2711.1

ASME A112.19.2—2013/CSA B45.1—13

Ceramic Plumbing Fixtures

Table P2701.1, P2705.1, P2711.1, P2712.1, P2712.2, P2712.9

ASME A112.19.3—2008/CSA B45.4—08 (R2013)

Stainless Steel Plumbing Fixtures

Table P2701.1, P2705.1, P2711.1, P2712.1

ASSE 1016/ASME 112.1016/CSA B125.16—2011

Performance Requirements for Automatic Compensating Valves for Individual Showers and Tub/Shower Combinations

Table P2701.1, P2708.4, P2722.2

A112.19.5—2011/CSA B45.15—2011

Flush Valves and Spuds for Water-closets, Urinals and Tanks

Table P2701.1

A112.19.7—2012/CSA B45.10—2012

Hydromassage Bathtub Systems

Table P2701.1

ASME A17.1/CSA B44—2013

Safety Code for Elevators and Escalators

R321.1

CSA 8—93

Requirements for Gas Fired Log Lighters for Wood Burning Fireplaces— with revisions through January 1999

G2433.1

A257.1M—2009

Circular Concrete Culvert, Storm Drain, Sewer Pipe and Fittings

Table P3002.2

A257.2M—2009

Reinforced Circular Concrete Culvert, Storm Drain, Sewer Pipe and Fittings

Table P3002.2, P3003.13

A257.3M—2009

Joints for Circular Concrete Sewer and Culvert Pipe, Manhole Sections and Fittings Using Rubber Gaskets

P3003.5

B64.1.1—11

Vacuum Breakers, Atmospheric Type (AVB)

Table P2902.3, P2902.3.2

B64.1.2—11

Pressure Vacuum Breakers (PVB)

Table P2902.3, P2902.3.4

B64.1.3—11

Spill Resistant Pressure Vacuum Breakers (SRPVB)

P2902.3.2

B64.2—11

Vacuum Breakers, Hose Connection Type (HCVP)

Table P2902.3, P2902.3.2

B64.2.1—11

Hose Connection Vacuum Breakers (HCVB) with Manual Draining Feature

Table P2902.3, P2902.3.2

B64.2.1.1—11

Hose Connection Dual Check Vacuum Breakers (HCDVB)

Table P2902.3, P2902.3.2

B64.2.2—11

Vacuum Breakers, Hose Connection Type (HCVP) with Automatic Draining Feature

Table P2902.3, P2902.3.2

B64.3—11

Dual Check Backflow Preventers with Atmospheric Port (DCAP)

Table P2902.3, P2902.5.1

B64.4—11

Backflow Preventers, Reduced Pressure Principle Type (RP)

Table P2902.3, P2902.3.5

B64.4.1—11

Reduced Pressure Principle for Fire Sprinklers (RPF)

Table P2902.3, P2902.3.5

B64.5—11

Double Check Backflow Preventers (DCVA)

Table P2902.3, P2902.3.6

B64.5.1—11

Double Check Valve Backflow Preventers, Type for Fire Systems (DCVAF)

Table P2902.3, P2902.3.6

B64.6—11

Dual Check Valve Backflow Preventers (DuC)

Table P2902.3, P2902.3.7

B64.7—11

Laboratory Faucet Vacuum Breakers (LFVB)

Table P2902.3, P2902.3.2

B117 (2016)

Standard Practice for Operating Salt Spray (FOG) Apparatus

R904.5.2

B125.3—12

Plumbing Fittings

Table 2701.1, P2713.3, P2721.2, Table P2902.3, P2902.4.1, Table P2903.9.4

B137.1—13

Polyethylene (PE) Pipe, Tubing and Fittings for Cold Water Pressure Services

Table P2906.4, Table P2906.6

B137.2—13

Polyvinylchloride PVC Injection-moulded Gasketed Fittings for Pressure Applications

Table P2906.6

B137.3—13

Rigid Poly (Vinyl Chloride) (PVC) Pipe for Pressure Applications

Table P2906.4, Table 2906.6, P3003.9.2, Table AG101.1

B137.5—13

Cross-linked Polyethylene (PEX) Tubing Systems for Pressure Applications

Table P2906.4, Table P2906.5, Table P2906.6, Table AG101.1

B137.6—13

Chlorinated polyvinylchloride CPVC Pipe, Tubing and Fittings For Hot- and Cold-water Distribution Systems

Table P2906.4, Table P2906.5, Table 2906.6, Table AG101.1

B137.9—13

Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe Systems

Table M2101.1, Table P2906.4

B137.10—13

Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PE-AL-PE) Composite Pressure Pipe Systems

Table M2101.1, Table P2906.4, Table P2906.5, Table P2906.6, P2906.11.1

B137.11—13

Polypropylene (PP-R) Pipe and Fittings for Pressure Applications

Table P2906.4, Table 2906.5, Table P2906.6, Table AG101.1

B181.1—11

Acrylonitrile-butadiene-styrene (ABS) Drain, Waste and Vent Pipe and Pipe Fittings

Table P3002.1(1), Table P3002.1(2), Table P3002.3, P3003.3.2, P3003.8.2

B181.2—11

Polyvinylchloride (PVC) and chlorinated polyvinylchloride (CPVC) Drain, Waste and Vent Pipe and Pipe Fittings

Table P3002.1(1), Table P3002.1(2), P3003.9.2, P3008.2, Table P3302.1

B181.3—11

Polyolefin and polyvinylidene (PVDF) Laboratory Drainage Systems

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3002.3, P3003.11.1

B182.2—11

PSM Type polyvinylchloride (PVC) Sewer Pipe and Fittings

Table P3002.2, Table P3002.3, Table P3302.1

B182.4—11

Profile polyvinylchloride (PVC) Sewer Pipe & Fittings

Table P3002.2, Table P3002.3, Table P3302.1

B182.6—11

Profile Polyethylene (PE) Sewer Pipe and Fittings for leak-proof Sewer Applications

Table P3302.1

B182.8—11

Profile Polyethylene (PE) Storm Sewer and Drainage Pipe and Fittings

Table P3302.1

B356—10

Water Pressure Reducing Valves for Domestic Water Supply Systems

P2903.3.1

B483.1—14

Drinking Water Treatment Systems

P2909.1, P2909.2

B602—10

Mechanical Couplings for Drain, Waste and Vent Pipe and Sewer Pipe

P3003.3.1, P3003.4.3, P3003.5, P3003.9.1, P3003.12.2, P3003.13

CSA B45.5—11/IAPMO Z124—11

Plastic Plumbing Fixtures

Table P2701.1, P2711.1, P2711.2, P2712.1

CSA C448 Series-02-CAN/CSA—2002

Design and Installation of Earth Energy Systems— First Edition; Update 2: October 2009; Consolidated Reprint 10/2009

Table M2105.4, Table M2105.5

O325—07

Construction Sheathing

R503.2.1, R602.1.8, R604.1, R803.2.1

O437-Series—93

Standards on OSB and Waferboard (Reaffirmed 2006)

R503.2.1, R602.1.8, R604.1, R803.2.1

UL/CSA/ANCE 60335-2-40—2012

Standard for Household and Similar Electrical Appliances, Part 2: Particular Requirements for Motor-compressors

M1403.1, M1412.1, M1413.1

CSSB

Cedar Shake & Shingle Bureau
P. O. Box 1178
Sumas WA 98295-1178
Standard
reference
number
TitleReferenced
in code
section number

CSSB—97

Grading and Packing Rules for Western Red Cedar Shakes and Western Red Shingles of the Cedar Shake and Shingle Bureau

R702.6, R703.6, Table R905.7.4, Table R905.8.5

New Roof Construction Manual (2015)

R905.7, R905.8

DASMA

Door and Access Systems Manufacturers Association International
1300 Summer Avenue
Cleveland OH 44115-2851
Standard
reference
number
TitleReferenced
in code
section number

108—12

Standard Method for Testing Garage Doors: Determination of Structural Performance Under Uniform Static Air Pressure Difference

R609.4

115—12

Standard Method for Testing Garage Doors: Determination of Structural Performance Under Missile Impact and Cyclic Wind Pressure

R301.2.1.2

DOC

United States Department of Commerce
1401 Constitution Avenue, NW
Washington DC 20230
Standard
reference
number
TitleReferenced
in code
section number

PS 2—10

Performance Standard for Wood-based Structural-use Panels

R404.2.1, Table R404.2.3, R503.2.1, R602.1.8, R604.1, R610.3.2, Table 610.3.2, R803.2.1

PS 20—05

American Softwood Lumber Standard

R404.2.1, R502.1.1, R602.1.1, R802.1.1

DOTn

Department of Transportation
1200 New Jersey Avenue SE
East Building, 2nd floor
Washington DC 20590
Standard
reference
number
TitleReferenced
in code
section number

14 CFR, Part 150 (2005)

Airport Noise Compatability Planning, Federal Aviation Administration

327.1

49 CFR, Parts 192.281(e) & 192.283 (b) (2009)

Transportation of Natural and Other Gas by Pipeline: Minimum Federal Safety Standards

G2414.6.1

FEMA

Federal Emergency Management Agency
500 C Street, SW
Washington DC 20472
Standard
reference
number
TitleReferenced
in code
section number

FEMA TB-2—08

Flood Damage-resistant Materials Requirements

R322.1.8

FEMA TB-11—01

Crawlspace Construction for Buildings Located in Special Flood Hazard Area

R408.7

Florida Codes

Florida Building Commission
Building Codes and Standards
Department of Business and Professional Regulation
1940 N. Monroe Street, Suite 90A
Tallahassee FL 32399-0772
Standard
reference
number
TitleReferenced
in code
section number

FBC-A—Sixth Edition (2017)

Florida Building Code, Accessibility

R320.1

FBC-B—Sixth Edition (2017)

Florida Building Code, Building

R101.2.1, R301.2.1.1, R301.2.1.6, R301.2.5, R322.1.11, R403.1.1, R403.1.2, R404.5.1, R905.3.1, R905.10.3, Table R907.7.1.2, M1904.1, R4401.1, R4402.1, R4403.1, R4404.1, R4405.1, R4406.1, R4407.1, R4408.1, R4409.1, R4410.1, R4411.1, R4412.1

FBC-EC—Sixth edition (2017)

Florida Building Code, Energy Conservation

R302.13, R408.3, R806.5, N1101

FBC-EB—Sixth edition (2017)

Florida Building Code, Existing Building

R101.2, R907.1, M1202.1, P2502, Table E3403

FFPC—Sixth edition (2017)

Florida Fire Prevention Code

M1904.1, M2201.7, G2412.2

FBC-FG—Sixth edition (2017)

Florida Building Code, Fuel Gas

M1301.1, M1904.1, G2401.1, G2423.1, R4501.1.2, R4501.15

FBC-M—Sixth edition (2017)

Florida Building Code, Mechanical

M1301.1, G2402.3, Table E3403, R4501.1.2, R4501.15

FBC-P—Sixth edition (2017)

Florida Building Code, Plumbing

Table R301.2(1), R903.4.1, G2402.3, P2601.1, P2902.5.5, R4501.1.2, R4501.3, R4501.8.1, R4501.13.2

64E

Rule 64E, Florida Administrative Code (Sewage Disposal)

R306.3, R322.1.7

FS

Florida Statutes

R202, R318.1.7

FBC-TPHVHZ—Sixth edition (2017)

Florida Building Code, Test Protocols for High-Velocity Hurricane Zones

RAS 109

R905.14

RAS 111

R905.2.8, R908.6

RAS 115

R905.2

RAS 130

R905.7, R905.8

FM

Factory Mutual Global Research
Standards Laboratories Department
1301 Atwood Avenue, P. O. Box 7500
Johnson RI 02919
Standard
reference
number
TitleReferenced
in code
section number

4450—(1989)

Approval Standard for Class 1 Insulated Steel Deck Roofs— with Supplements through July 1992

R906.1

4880—(2010)

American National Standard for Evaluating Insulated Wall or Wall and Roof/Ceiling Assemblies, Plastic Interior Finish Materials, Plastic Exterior Building Panels, Wall/Ceiling Coating Systems, Interior and Exterior Finish Systems

R316.6

FRSA

Florida Roofing, Sheet Metal and Air Conditioning Contractors Association
4111 Metric Drive
Winter Park FL 32792
Standard
reference
number
TitleReferenced
in code
section number

FRSA/TRI

Florida High Wind Concrete and Clay Roof Tile Installation Manual, Fifth Edition, Revised April 2012

R905.3, R905.3.2, R905.3.3, R905.3.3.1, R905.3.6, R905.3.7, R905.3.7.1, R905.3.8

GA

Gypsum Association
6525 Belcrest Road, Suite 480
Hyattsville MD 20782
Standard
reference
number
TitleReferenced
in code
section number

GA-253—12

Application of Gypsum Sheathing

Table R602.3(1)

HPVA

Hardwood Plywood & Veneer Association
1825 Michael Faraday Drive
Reston Virginia 20190-5350
Standard
reference
number
TitleReferenced
in code
section number

ANSI/HP-1—2013

Standard for Hardwood and Decorative Plywood

R702.5

IAPMO

IAPMO
4755 E. Philadelphia Street
Ontario CA 91761-USA
Standard
reference
number
TitleReferenced
in code
section number

CSA B45.5—11/IAPMO Z124—11

Plastic Plumbing Fixtures

Table P2701.1, P2711.1, P2711.2, P2712.1

ICC

International Code Council, Inc.
500 New Jersey Avenue, NW
6th Floor
Washington DC 20001
Standard
reference
number
TitleReferenced
in code
section number

ICC/ANSI A117.1—09

Accessible and Usable Buildings and Facilities

R321.3

ICC 400—12

Standard on the Design and Construction of Log Structures

R301.1.1, 502.1.4, R602.1.4, R703.1, R802.1.3

ICC 500—14

ICC/NSSA Standard on the Design and Construction of Storm Shelters

R323.1

ICC 600—14

Standard for Residential Construction in High-wind Regions

R301.2.1.1

ISO

International Organization for Standardization
1, ch. de la Voie - Creuse
Case postale 56
Geneva 20 Switzerland CH-1211
Standard
reference
number
TitleReferenced
in code
section number

8336—2009

Fibre-cement Flat Sheets-product Specification and Test Methods

Table R503.2.1.1(1), Table R503.2.1.1(2), Table R602.3(2), Table R702.4.2, R703.10.1, R703.10.2

15874—2002

Polypropylene Plastic Piping Systems for Hot and Cold Water Installations

Table M2101.1

MAF

Masonry Association of Florida
398 Camino Gardens Blvd, Suite 108
Boca Raton FL 33432
Standard
reference
number
TitleReferenced
in code
section number

MAF—97

Guide to Concrete Masonry Residential Construction in High Wind Areas

R301.2.1.1

MSS

Manufacturers Standardization Society of the Valve and Fittings Industry
127 Park Street, Northeast
Vienna VA 22180
Standard
reference
number
TitleReferenced
in code
section number

SP-42—09

Corrosion Resistant Gate, Globe, Angle and Check Valves with Flanged and Butt Weld Ends (Glasses 150, 300 & 600)

Table P2903.9.4

SP-58—09

Pipe Hangers and Supports—Materials, Design, Manufacture, Selection, Application and Installation

G2418.2

SP-67—11

Butterfly Valves

Table P2903.9.4

SP-70—11

Gray Iron Gate Valves, Flanged and Threaded Ends

Table P2903.9.4

SP-71—11

Gray Iron Swing Check Valves, Flanged and Threaded Ends

Table P2903.9.4

SP-72—10

Ball Valves with Flanged or Butt-Welding Ends for General Service

P2903.9.4

SP-78—11

Cast Iron Plug Valves, Flanged and Threaded Ends

Table P2903.9.4

SP-80—08

Bronze Gate, Globe, Angle and Check Valves

Table P2903.9.4

SP-110—10

Ball Valves, Threaded, Socket Welded, Solder Joint, Grooved and Flared Ends

Table P2903.9.4

NAIMA

North American Insulation Manufacturers Association
44 Canal Center Plaza, Suite 310
Alexandria VA 22314
Standard
reference
number
TitleReferenced
in code
section number

AH 116—09

Fibrous Glass Duct Construction Standards, Fifth Edition

M1601.1.1

NFPA

National Fire Protection Association
1 Batterymarch Park
Quincy MA 02269
Standard
reference
number
TitleReferenced
in code
section number

13—13

Installation of Sprinkler Systems

R302.3

13D—13

Standard for the Installation of Sprinkler Systems in One- and Two-family Dwellings and Manufactured Homes

R302.13, R325.5, P2904.1, P2904.6.1

13R—13

Standard for the Installation of Sprinkler Systems in Low Rise Residential Occupancies

R325.5

31—11

Standard for the Installation of Oil-burning Equipment

M1701.1, M1801.3.1, M1805.3

58—14

Liquefied Petroleum Gas Code

G2412.2, G2414.6.2

70—14

National Electrical Code

E3401.1, E3401.2, E4301.1, Table E4303.2, E4304.3, E4304.4, R324.3

72—13

National Fire Alarm and Signaling Code

R314.1, R314.7.1

85—15

Boiler and Combustion Systems Hazards Code

G2452.1

211—13

Standard for Chimneys, Fireplaces, Vents and Solid Fuel Burning Appliances

R1002.5, G2427.5.5.1

259—13

Standard for Test Method for Potential Heat of Building Materials

R316.5.7, R316.5.8

275—13

Standard Method of Fire Tests for the Evaluation of Thermal Barriers

R316.4

286—15

Standard Methods of Fire Tests for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth

R302.9.4, R316.6

501—13

Standard on Manufactured Housing

R202

720—15

Standard for the Installation of Carbon Monoxide (CO) Detectors and Warning Equipment

853—15

Standard on the Installation of Stationary Fuel Cell Power Systems

M1903.1

NSF

NSF International
789 N. Dixboro
Ann Arbor MI 48105
Standard
reference
number
TitleReferenced
in code
section number

14—2011

Plastics Piping System Components and Related Materials

M1301.4, P2609.3, P2909.3

41—2011

Nonliquid Saturated Treatment Systems (Composting Toilets)

P2725.1

42—2011

Drinking Water Treatment Units—Anesthetic Effects

P2909.1, P2909.3

44—2012

Residential Cation Exchange Water Softeners

P2909.1, P2909.3

50—2012

Equipment for Swimming Pools, Hot Tubs and Other Recreational Water Facilities

P2911.8.1

53—2011A

Drinking Water Treatment Units—Health Effects

P2909.1, P2909.3

58—2012

Reverse Osmosis Drinking Water Treatment Systems

P2909.2, P2909.3

61—2012

Drinking Water System Components—Health Effects

P2609.5, P2722.1, P2903.9.4, P2906.4, P2906.5, P2906.6

350—2011

Onsite Residential and Commercial Water Reuse Treatment Systems

358-1—2011

Polyethylene Pipe and Fittings for Water-based Ground Source “Geothermal” Heat Pump Systems

M2105.4, M2105.5, Table AG101.1

358-2—2012

Polypropylene Pipe and Fittings for Water-based Ground Source “Geothermal” Heat Pump Systems

M2105.5

359—2012

Valves for Crosslinked Polyethylene (PEX) Water Distribution Tubing Systems

Table P2903.9.4

372—2010

Drinking Water Systems Components—Lead Content

P2906.2.1

PCA

Portland Cement Association
5420 Old Orchard Road
Skokie IL 60077
Standard
reference
number
TitleReferenced
in code
section number

100—12

Prescriptive Design of Exterior Concrete Walls for One- and Two-family Dwellings (Pub. No. EB241)

R301.2.2.2.4, R301.2.2.3.4, R404.1.3, R404.1.3.2.1, R404.1.3.2.2, R404.1.3.4, R404.1.4.2, R608.1, R608.2, R608.5.1, R608.9.2, R608.9.3

SBCA

Structural Building Components Association
6300 Enterprise Lane
Madison WI 53719
Standard
reference
number
TitleReferenced
in code
section number

BCSI—2013

Building Component Safety Information Guide to Good Practice for Handling, Installing, Restraining & Bracing of Metal Plate Connected Wood Trusses

502.11.2, 802.10.3

CFS-BCSI—2008

Cold-formed Steel Building Component Safety Information (CFSBCSI) Guide to Good Practice for Handling, Installing & Bracing of Cold-formed Steel Trusses

505.1.3, 804.3.6

FS100—12

Standard Requirements for Wind Pressure Resistance of Foam Plastic Insulating Sheathing Used in Exterior Wall Covering Assemblies

R316.8

SMACNA

Sheet Metal & Air Conditioning Contractors National Assoc. Inc.
4021 Lafayette Center Road
Chantilly VA 22021
Standard
reference
number
TitleReferenced
in code
section number

SMACNA—10

Fibrous Glass Duct Construction Standards (2003)

M1601.1.1, M1601.4.1

SMACNA/ANSI—2005

HVAC Duct Construction Standards, Metal and Flexible (2005)

M1601.4.1

SRCC

Solar Rating & Certification Corporation
400 High Point Drive, Suite 400
Cocoa FL 32926
Standard
reference
number
TitleReferenced
in code
section number

SRCC 100—13

Standard 100 for Solar Collectors

M2301.3.1

SRCC 300—13

Standard 300 for Solar Water Heating Systems

M2301.2.3, M2301.4, M2301.2.6, M2301.2.8

SRCC 600—13

Standard 600 for Solar Concentrating Collectors

M2301.3.1

TMS

The Masonry Society
105 South Sunset Street, Suite Q
Longmont CO 80501
Standard
reference
number
TitleReferenced
in code
section number

402—2016

Building Code Requirements for Masonry Structures

R404.1.2, R606.1, R606.1.1, R606.12.1, R606.12.2.3.1, R606.12.3.1, Table R703.4, 703.12

403—2013

Direct Design Handbook for Masonry Structures

R606.1, R606.1.1, R606.12.1, R606.12.3.1

602—2016

Specification for Masonry Structures

R404.1.2, R606.2.9, R606.2.12, R606.12.3.1, R703.12

TPI

Truss Plate Institute
218 N. Lee Street, Suite 312
Alexandria VA 22314
Standard
reference
number
TitleReferenced
in code
section number

TPI 1—2014

National Design Standard for Metal-plate-connected Wood Truss Construction

R502.11.1, R802.10.2

UL

UL LLC
333 Pfingsten Road
Northbrook IL 60062
Standard
reference
number
TitleReferenced
in code
section number

17—2008

Vent or Chimney Connector Dampers for Oil-fired Appliances— with revisions through January 2010

M1802.2.2

55A—04

Materials for Built-up Roof Coverings

R905.9.2

58—14

Liquefied Petroleum Gas Code

M2201.1

80—2007

Steel Tanks for Oil-burner Fuel—with revisions August 2009

M2201.1

103—2010

Factory-built Chimneys for Residential Type and Building Heating Appliances—with revisions through July 2012

R202, R1005.3, G2430.1

174—04

Household Electric Storage Tank Water Heaters— with revisions through September 2012

M2005.1

180—2012

Liquid-level Indicating Gauges for Oil Burner Fuels and Other Combustible Liquids

M2201.5

181—05

Factory-made Air Ducts and Air Connectors—with revisions through May 2003

M1601.1.1, M1601.4.1

181A—2013

Closure Systems for Use with Rigid Air Ducts and Air Connectors— with revisions through December 1998

M1601.2, M1601.4.1

181B—2013

Closure Systems for Use with Flexible Air Ducts and Air Connectors— with revisions through August 2003

M1601.4.1

217—06

Single- and Multiple-station Smoke Alarms—with revisions through April 2012

R314.1.1, R315.1.1

263—2011

Standards for Fire Test of Building Construction and Materials

Table 302.1(1), Table R302.1(2), R302.2, R302.3, R302.4.1, R302.11.1, R606.2.2

268—2009

Smoke Detectors for Fire Alarm Systems

R314.7.1, R314.7.4

325—02

Door, Drapery, Gate, Louver and Window Operations and Systems— with revisions through June 2013

R309.4

343—2008

Pumps for Oil-burning Appliances—with revisions through June 2013

M2204.1

378—06

Draft Equipment—with revisions through January 2010

M1804.2.6

441—10

Gas Vents

G2426.1

508—99

Industrial Control Equipment—with revisions through March 2013

M1411.3.1

536—97

Flexible Metallic Hose—with revisions through June 2003

M2202.3

641—2010

Type L, Low-temperature Venting Systems— with revisions through May 2013

R202, R1003.11.5, M1804.2.4, G2426.1

651—2011

Schedule 40 and Schedule 80 Rigid PVC Conduit and Fittings— with revisions through March 2012

G2414.6.3

705—04

Standard for Power Ventilators—with revisions through March 2012

M1502.4.4

723—08

Standard for Test for Surface Burning Characteristics of Building Materials—with revisions through September 2010

R202, R302.9.3, R302.9.4, R302.10.1, R302.10.2, R316.3, R316.5.9, R316.5.11, R507.3.2, R802.1.5, M1601.3, M1601.5.2

726—95

Oil-fired Boiler Assemblies—with revisions through April 2011

M2001.1.1, M2006.1

727—06

Oil-fired Central Furnaces—with revisions through April 2010

M1402.1

729—03

Oil-fired Floor Furnaces—with revisions through August 2012

M1408.1

730—03

Oil-fired Wall Furnaces—with revisions through August 2012

M1409.1

732—95

Oil-fired Storage Tank Water Heaters—with revisions through April 2010

M2005.1

737—2011

Fireplaces Stoves

M1414.1, M1901.2

790—04

Standard Test Methods for Fire Tests of Roof Coverings— with revisions through October 2008

R302.2.2, R902.1

795—2011

Commercial-industrial Gas Heating Equipment— with revisions through September 2012

G2442.1, G2452.1

834—04

Heating, Water Supply and Power Boilers—Electric—with revisions through January 2013

M2001.1.1

842—07

Valves for Flammable Fluids—with revisions through October 2012

M2204.2

858—05

Household Electric Ranges—with revisions through April 2012

M1901.2

875—09

Electric Dry-bath Heaters with revisions through November 2011

M1902.2

896—93

Oil-burning Stoves—with revisions through August 2012

M1410.1

923—2013

Microwave Cooking Appliances

M1504.1

1026—2012

Electric Household Cooking and Food Serving Appliances

M1901.2

1040—96

Fire Test of Insulated Wall Construction—with revisions through October 2012

R316.6

1042—2009

Electric Baseboard Heating Equipment—with revisions through June 2013

M1405.1

1256—02

Fire Test of Roof Deck Construction—with revisions through January 2007

R906.1

1261—01

Electric Water Heaters for Pools and Tubs—with revisions through July 2012

M2006.1

1479—03

Fire Tests of Through-Penetration Firestops—with revisions through October 2012

R302.4.1.2

1482—2011

Solid-Fuel-type Room Heaters

R1002.2, R1002.5, M1410.1

1618—09

Wall Protectors, Floor Protectors, and Hearth Extensions— with revisions through May 2013

R1004.2, M1410.2

1693—2010

Electric Radiant Heating Panels and Heating Panel Sets— with revisions through October 2011

M1406.1

1703—02

Flat-plate Photovoltaic Modules and Panels—with revisions through November 2014

R324.3.1, R902.4, R905.17.4, R907.5

1715—97

Fire Test of Interior Finish Material—with revisions through January 2013

R316.6

1738—2010

Venting Systems for Gas-burning Appliances, Categories II, III and IV— with revisions Through May 2011

G2426.1

1741—2010

Inverters, Converters, Controllers and Interconnection System Equipment for use with Distributed Energy Resources

R324.3

1777—07

Chimney Liners—with revisions through July 2009

R1003.11.1, R1003.18, G2425.12, G2425.15.4, M1801.3.4

1995—2011

Heating and Cooling Equipment

M1402.1, M1403.1, M1407.1, M1412.1, M1413.1

1996—2009

Electric Duct Heaters—with revisions through November 2011

M1402.1, M1407.1

2034—08

Standard for Single- and Multiple-station Carbon Monoxide Alarms—with revisions through February 2009

R202, R314.1.1, R315.1.1

2075—2013

Standard for Gas and Vapor Detectors and Sensors

R202, R314.7.4

2158A—2010

Outline of Investigation for Clothes Dryer Transition Duct

M1502.4.3

2523—09

Standard for Solid Fuel-fired Hydronic Heating Appliances, Water Heaters and Boilers— with revisions through February 2013

M2005.1, M2001.1.1

UL/CSA/ANCE 60335-2-40—2012

Standard for Household and Similar Electrical Appliances, Part 2: Particular Requirements for Motor-compressors

M1403.1, M1412.1, M1413.1

ULC

ULC
7 Underwriters Road
Toronto, Ontario Canada M1R 3B4
Standard
reference
number
TitleReferenced
in code
section number

CAN/ULC S 102.2—2010

Standard Methods for Test for Surface Burning Characteristics of Building Materials and Assemblies

R302.10.1, R302.10.2

WDMA

Window & Door Manufacturers Association
2025 M Street, NW Suite 800
Washington DC 20036-3309
Standard
reference
number
TitleReferenced
in code
section number

AAMA/WDMA/CSA 101/I.S2/A440—11

North American Fenestration Standard/ Specifications for Windows, Doors and Skylights

R308.6.9, R609.3

I.S. 11—13

Industry Standard Analytical Method for Design Pressure (DP) Ratings of Fenestration Products

R308.6.9.1, R609.3.1

WMA

World Millwork Alliance
10047 Robert Trent Parkway
New Port Richey FL 34655-4649
Standard
reference
number
TitleReferenced
in code
section number

ANSI/WMA 100—2016

Standard Method of Determining Structural Performance Ratings of Side Hinged Exterior Door Systems and Procedures for Component Substitution

R609.3

Resources