UpCodes logo
// CODE SNIPPET

Appendix B Substance Technical Guidelines for 1,3-Butadiene (Non-Mandatory)

Go To Full Code Chapter
  1. Physical and Chemical Data

    1. Substance identification:

      1. Synonyms: 1,3-Butadiene (BD); butadiene; biethylene; bivinyl; divinyl; butadiene-1,3; buta-1,3-diene; erythrene; NCI-C50620; CAS-106-99-0.
      2. Formula: CH2 = CH-CH = CH2.
      3. Molecular weight: 54.1.
    2. Physical data:

      1. Boiling point (760 mm Hg): -4.7 °C (23.5 °F).
      2. Specific gravity (water=1): 0.62 at 20 °C (68 °F).
      3. Vapor density (air=1 at boiling point of BD): 1.87.
      4. Vapor pressure at 20 °C (68 °F): 910 mm Hg.
      5. Solubility in water, g/100 g water at 20 °C (68 °F): 0.05.
      6. Appearance and odor: Colorless, flammable gas with a mildly aromatic odor. Liquefied BD is a colorless liquid with a mildly aromatic odor.
  2. Fire, Explosion, and Reactivity Hazard Data

    1. Fire:

      1. Flash point: -76 °C (-105 °F) for take out; liquefied BD; Not applicable to BD gas.
      2. Stability: A stabilizer is added to the monomer to inhibit formation of polymer during storage. Forms explosive peroxides in air in absence of inhibitor.
      3. Flammable limits in air, percent by volume: Lower: 2.0; Upper: 11.5.
      4. Extinguishing media: Carbon dioxide for small fires, polymer or alcohol foams for large fires.
      5. Special fire fighting procedures: Fight fire from protected location or maximum possible distance. Stop flow of gas before extinguishing fire. Use water spray to keep fire-exposed cylinders cool.
      6. Unusual fire and explosion hazards: BD vapors are heavier than air and may travel to a source of ignition and flash back. Closed containers may rupture violently when heated.
      7. For purposes of compliance with the requirements of 29 CFR 1910.106, BD is classified as a flammable gas. For example, 7,500 ppm, approximately one-fourth of the lower flammable limit, would be considered to pose a potential fire and explosion hazard.
      8. For purposes of compliance with 29 CFR 1910.155, BD is classified as a Class B fire hazard.
      9. For purposes of compliance with 29 CFR 1910.307, locations classified as hazardous due to the presence of BD shall be Class I.
    2. Reactivity:

      1. Conditions contributing to instability: Heat. Peroxides are formed when inhibitor concentration is not maintained at proper level. At elevated temperatures, such as in fire conditions, polymerization may take place.
      2. Incompatibilities: Contact with strong oxidizing agents may cause fires and explosions. The contacting of crude BD (not BD monomer) with copper and copper alloys may cause formations of explosive copper compounds.
      3. Hazardous decomposition products: Toxic gases (such as carbon monoxide) may be released in a fire involving BD.
      4. Special precautions: BD will attack some forms of plastics, rubber, and coatings. BD in storage should be checked for proper inhibitor content, for self-polymerization, and for formation of peroxides when in contact with air and iron. Piping carrying BD may become plugged by formation of rubbery polymer.
    3. Warning Properties:

      1. Odor Threshold: An odor threshold of 0.45 ppm has been reported in The American Industrial Hygiene Association (AIHA) Report, Odor Thresholds for Chemicals with Established Occupational Health Standards. (Ex. 32-28C)
      2. Eye Irritation Level: Workers exposed to vapors of BD (concentration or purity unspecified) have complained of irritation of eyes, nasal passages, throat, and lungs. Dogs and rabbits exposed experimentally to as much as 6700 ppm for 7 1/2 hours a day for 8 months have developed no histologically demonstrable abnormality of the eyes.
      3. Evaluation of Warning Properties: Since the mean odor threshold is about half of the 1 ppm PEL, and more than 10-fold below the 5 ppm STEL, most wearers of air purifying respirators should still be able to detect breakthrough before a significant overexposure to BD occurs.
  3. Spill, Leak, and Disposal Procedures

    1. Persons not wearing protective equipment and clothing should be restricted from areas of spills or leaks until cleanup has been completed. If BD is spilled or leaked, the following steps should be taken:

      1. Eliminate all ignition sources.
      2. Ventilate areas of spill or leak.
      3. If in liquid form, for small quantities, allow to evaporate in a safe manner.
      4. Stop or control the leak if this can be done without risk. If source of leak is a cylinder and the leak cannot be stopped in place, remove the leaking cylinder to a safe place and repair the leak or allow the cylinder to empty.
    2. Disposal: This substance, when discarded or disposed of, is a hazardous waste according to Federal regulations (40 CFR part 261). It is listed by the EPA as hazardous waste number D001 due to its ignitability. The transportation, storage, treatment, and disposal of this waste material must be conducted in compliance with 40 CFR parts 262, 263, 264, 268 and 270. Disposal can occur only in properly permitted facilities. Check state and local regulations for any additional requirements because these may be more restrictive than federal laws and regulations.
  4. Monitoring and Measurement Procedures

    1. Exposure above the Permissible Exposure Limit (8-hr TWA) or Short-Term Exposure Limit (STEL):

      1. 8-hr TWA exposure evaluation: Measurements taken for the purpose of determining employee exposure under this standard are best taken with consecutive samples covering the full shift. Air samples must be taken in the employee's breathing zone (air that would most nearly represent that inhaled by the employee).
      2. STEL exposure evaluation: Measurements must represent 15 minute exposures associated with operations most likely to exceed the STEL in each job and on each shift.
      3. Monitoring frequencies: Table 1 gives various exposure scenarios and their required monitoring frequencies, as required by the final standard for occupational exposure to butadiene.

        Table 1 - Five Exposure Scenarios and Their Associated
        Monitoring Frequencies
        Action
        level
        8-hr
        TWA
        STEL Required monitoring activity
        -* - - No 8-hr TWA or STEL monitoring required.
        * - - No STEL monitoring required. Monitor 8-hr TWA annually.
        - No STEL monitoring required. Periodic monitoring 8-hr TWA, in accordance with (d)(3)(ii).**
        Periodic monitoring 8-hr TWA, in accordance with (d)(3)(ii)**. Periodic monitoring STEL, in accordance with (d)(3)(iii).
        - Periodic monitoring STEL, in accordance with (d)(3)(iii). Monitor 8-hr TWA, annually.
           Footnote(*) Exposure Scenario, Limit Exceeded: = Yes, - = No.
           Footnote(**) The employer may decrease the frequency of exposure
        monitoring to annually when at least 2 consecutive measurements taken at least 7 days apart show exposures to be below the 8 hr TWA, but at or above the action level.
      4. Monitoring techniques: Appendix D describes the validated method of sampling and analysis which has been tested by OSHA for use with BD. The employer has the obligation of selecting a monitoring method which meets the accuracy and precision requirements of the standard under his or her unique field conditions. The standard requires that the method of monitoring must be accurate, to a 95 percent confidence level, to plus or minus 25 percent for concentrations of BD at or above 1 ppm, and to plus or minus 35 percent for concentrations below 1 ppm.
  5. Personal Protective Equipment

    1. Employees should be provided with and required to use impervious clothing, gloves, face shields (eight-inch minimum), and other appropriate protective clothing necessary to prevent the skin from becoming frozen from contact with liquid BD.
    2. Any clothing which becomes wet with liquid BD should be removed immediately and not re-worn until the butadiene has evaporated.
    3. Employees should be provided with and required to use splash proof safety goggles where liquid BD may contact the eyes.
  6. Housekeeping and Hygiene Facilities

        For purposes of complying with 29 CFR 1910.141, the following items should be emphasized:

    1. The workplace should be kept clean, orderly, and in a sanitary condition.
    2. Adequate washing facilities with hot and cold water are to be provided and maintained in a sanitary condition.
  7. Additional Precautions

    1. Store BD in tightly closed containers in a cool, well-ventilated area and take all necessary precautions to avoid any explosion hazard.
    2. Non-sparking tools must be used to open and close metal containers. These containers must be effectively grounded.
    3. Do not incinerate BD cartridges, tanks or other containers.
    4. Employers must advise employees of all areas and operations where exposure to BD might occur.
[61 FR 56746, Nov. 4, 1996]

Related Code Sections

1910.1051(k) Toxic and Hazardous Substances, Medical Screening and Surveillance
screening and surveillance for employees, even after transfer to a non-BD exposed job and regardless of when the employee is transferred, whose work ...