R609.6.1 Preengineered Assemblies for Masonry Walls

Unreinforced masonry units above an opening and 8-inch (203 mm) high bond beams above an opening shall be supported by an assembly.

Preengineered assemblies shall be selected from a manufacturer's approved schedule or other approved tables for the load capacities based on the appropriate minimum gravity load carrying capacities established in Tables R609.6.1.2(1), R609.6.1.2(2), and R609.6.1.2(3).

TABLE R609.6.1.2(1)
SUPERIMPOSED LOADS MINIMUM RATED LOAD CAPACITY OF 6-INCHOR 8-INCH-THICK PREENGINEERED ASSEMBLIES SPANNING OPENINGS OF ONE STORY AND TOP STORY OF MULTISTORY BUILDINGS^1,3,4

ROOF SPAN (FT)	UPLIFT (plf)
	GRAVITY (plf)	Vasd as determined in accordance with Section R301.2.1.3
		100 mph	120 mph	140 mph
42	150	85	112	165
12	330	152	204	305
24	600	262	351	525
36	870	374	502	745
44	1,050	451	605	900
52	1,230	530	710	1,055
60	1,410	609	816	1,215

Notes:

1. All loads are superimposed at the top of the wall and do not include dead loads of the bond beam or masonry above the assembly. Add 100 percent of additional dead loads to the gravity loads and subtract 85 percent of these loads from the uplift loads.
2. Use 4-foot (1220 mm) roof span for assemblies in endwalls.
3. For total roof dead loads over 10 psf, increase gravity loads by the following amount: (Roof Dead Load - 10 psf) × (Roof Span + 2 ft)/2.
4. Uplift rating is required only if a pre-engineered assembly is used to directly support a roof. See Section R609.6.1.3 for cases where uplift need not be considered.

TABLE R609.6.1.2(2)
SUPERIMPOSED LOADS MINIMUM RATED LOAD CAPACITY 8-INCH-THICK PREENGINEERED ASSEMBLIES SPANNING OPENINGS OF BOTTOM STORY OF TWO-STORY BUILDINGS, SECOND AND BOTTOM STORIES OF THREE-STORY BUILDINGS— WOOD FLOOR SYSTEM^3,4,5

FLOOR SPAN1 (FT)	MINIMUM RATED GRAVITY LOAD ASSEMBLY (plf)
	ASSEMBLY CLEAR SPAN (FT)
	4	6	8	12	16	20
42	210	260	310	410	510	610
12	430	480	530	630	730	830
24	760	810	860	960	1,060	1,160
36	1,090	1,140	1,190	1,290	1,390	1,490
44	1,310	1,360	1,410	1,510	1,610	1,710
52	1,530	1,580	1,630	1,730	1,830	1,930
60	1,750	1,800	1,850	1,950	2,050	2,150

Notes:

1. For a wall supporting floors on both sides, enter table with the sum of the 2 full spans.
   
   NOTE: Tabular values are for half the load of the full span shown.
2. Use 4-foot (1220 mm) building width for assemblies in walls not supporting floors (normally endwalls and interior masonry walls and shearwalls).
3. The values in this table may be interpolated.
4. These loads take into account the dead load of any masonry in the wall above the assembly and live and dead loads of the roof and floor supported. Dead load of the assembly is not included in the table and if not included in the preengineered concrete design must be added to the loads in the table.
5. This table is applicable for all roof dead loads.

TABLE R609.6.1.2(3)
SUPERIMPOSED LOADS MINIMUM RATED LOAD CAPACITY 8-INCH-THICK PREENGINEERED ASSEMBLIES SPANNING OPENINGS OF BOTTOM STORY OF TWO-STORY BUILDINGS, SECOND AND BOTTOM STORIES OF THREE-STORY BUILDINGS—HOLLOWCORE FLOOR SYSTEM^3,4,5

FLOOR SPAN1 (FT)	MINIMUM RATED GRAVITY LOAD ASSEMBLY (plf)
	ASSEMBLY CLEAR SPAN (FT)
	4	6	8	12	16	20
42	290	340	390	490	590	690
12	670	720	770	870	970	1,070
24	1,240	1,290	1,340	1,440	1,540	1,640
36	1,810	1,860	1,910	2,010	2,110	2,210
44	2,190	2,240	2,290	2,390	2,490	2,590
52	2,570	2,620	2,670	2,770	2,870	2,970
60	2,950	3,000	3,050	3,150	3,250	3,350

Notes:

1. For a wall supporting floors on both sides, enter table with the sum of the 2 full spans.
   
   NOTE: Tabular values are for half the load of the full span shown.
2. Use 4-foot (1220 mm) building width for assemblies in nonfloor bearing walls (normally endwalls and interior masonry walls and shearwalls).
3. The values in this table may be interpolated.
4. These loads take into account the dead load of any masonry in the wall above the assembly and live and dead loads of the roof and floor supported. Dead load of the assembly is not included in the table and if not included in the preengineered concrete assembly design must be added to the loads in the table.
5. This table is applicable for all roof dead loads.

Preengineered assemblies may function as a bond beam over an opening provided that:

1. The bond beam reinforcement is continuous through the assembly.
2. The assembly has an uplift rating that equals or exceeds the appropriate value stipulated in Table R609.6.1.2(1) if the lintel directly supports a roof.

Preengineered assemblies spanning openings shall extend a minimum of 4 inches (102 mm) nominal past each side of the opening.