// CODE SNIPPET
Section M2104 Low Temperature Piping
JUMP TO FULL CODE CHAPTER
Low temperature piping for embedment in concrete or gypsum materials shall be as indicated in Table M2101.1.
Piping joints, other than those in
Section M2103.3, that are embedded shall comply with the
following requirements:
- Cross-linked polyethylene (PEX) tubing shall be installed in accordance with the manufacturer's instructions.
- Polyethylene tubing shall be installed with heat fusion joints.
- Polypropylene (PP) tubing shall be installed in accordance with the manufacturer's instructions.
- Raised temperature polyethylene (PE-RT) shall be installed in accordance with the manufacturer's instructions.
Joints between raised temperature polyethylene
tubing and fittings shall conform to Sections M2104.3.1,
M2104.3.2 and M2104.3.3. Mechanical joints shall be
installed in accordance with the manufacturer's instructions.
Where compression-type fittings include inserts and ferrules or O-rings,
the fittings shall be installed without omitting such inserts
and ferrules or O-rings.
Solder joints in
a metal pipe shall not occur within 18 inches (457 mm) of
a transition from such metal pipe to PE-RT pipe.
PE-RT insert fittings
shall be installed in accordance with the manufacturer's
instructions.
Joints between polyethylene/aluminum/
polyethylene pressure pipe and fittings shall conform to Sections
M2104.4.1 and M2104.4.2. Mechanical joints shall be
installed in accordance with the manufacturer's instructions.
Where compression-type fittings include inserts and ferrules or O-rings,
the fittings shall be installed without omitting such inserts
and ferrules or O-rings.
Solder
joints in a metal pipe shall not occur within 18 inches (457
mm) of a transition from such metal pipe to PE-AL-PE
pipe.
Related Code Sections
Section M2104 Hydronic Piping, Low Temperature Piping
Low temperature piping for embedment in concrete or gypsum materials shall be as indicated in Table M2101.1 ...
M2104.4.2 Hydronic Piping, PE-AL-PE to Metal Connections
Solder
joints in a metal pipe shall not occur within 18 inches (457
mm) of a transition from such metal pipe to PE-AL-PE
pipe ...
2015 Michigan Residential Code > 21 Hydronic Piping > M2104 Low Temperature Piping > M2104.4 Polyethylene/ Aluminum/Polyethylene (Pe-Al-PE) Pressure Pipe > M2104.4.2 PE-AL-PE to Metal Connections
M2104.3.2 Hydronic Piping, PE-RT-To-Metal Connections
Solder joints in
a metal pipe shall not occur within 18 inches (457 mm) of
a transition from such metal pipe to PE-RT pipe ...
2015 Michigan Residential Code > 21 Hydronic Piping > M2104 Low Temperature Piping > M2104.3 Raised Temperature Polyethylene (PE-RT) Plastic Tubing > M2104.3.2 PE-RT-To-Metal Connections
M2104.3.1 Hydronic Piping, Compression-Type Fittings
Where compression-type fittings include inserts and ferrules or O-rings,
the fittings shall be installed without omitting such inserts
and ferrules ...
2015 Michigan Residential Code > 21 Hydronic Piping > M2104 Low Temperature Piping > M2104.3 Raised Temperature Polyethylene (PE-RT) Plastic Tubing > M2104.3.1 Compression-Type Fittings
M2104.3.3 Hydronic Piping, PE-RT Insert Fittings
PE-RT insert fittings
shall be installed in accordance with the manufacturer's
instructions ...
2015 Michigan Residential Code > 21 Hydronic Piping > M2104 Low Temperature Piping > M2104.3 Raised Temperature Polyethylene (PE-RT) Plastic Tubing > M2104.3.3 PE-RT Insert Fittings