# 6.1 Concentrically Braced Frames

The building satisfies the Quick Check of the stress in the diagonals.

For conforming buildings, the evaluator may consider this condition as mitigated, and no calculations are necessary. Calculate the average axial stress in the diagonals using the procedures of Section 2.4.7.4. Increase the calculated stress to account for torsion, based on the amount of torsion (Section 3.3.6) present and the distance between braced frames. If the average stress exceeds 30 ksi, an accurate analysis of the stresses on the bracing elements shall be performed.

All diagonal elements required to carry compression have *Kl/r* ratios less than 120.

For conforming buildings, the evaluator may consider this condition as mitigated, and no calculations are necessary. The deficiency is in the stiffness of the diagonals. Check the bracing elements, amplifying the seismic force by the factor 1.25.

Tension-only braces are not used as the primary diagonal bracing elements in structures over two stories in height.

The deficiency is in the strength of the braces. Check the braces. If they are tension-only, and the building is over two stories in height, place the building in SPC 1. Tension-only bracing of small penthouse structures may be reviewed using the procedures in Section 2.4.6. Conforming buildings which fail this check shall be placed in SPC 4.

The bracing system does not include chevron-, V-, or K-braced bays.

For conforming buildings, the evaluator may consider this condition as mitigated, and no calculations are necessary. Check all elements in the braced frames. For chevron- and V-braced frames, the beam shall be a single element that can carry the gravity loads without the intermediate support of the braces. Check the adequacy of the beam for the seismic forces amplified by *C _{d}*/2, but not less than 1.5. Consider the effect of buckling of a leg of chevron-bracing or V-bracing, including the continuity, strength, and bracing of the beams and the ability of the connection to permit buckling of the brace while not destroying the capacity for repeated cycles of loading. If K-bracing is used in buildings over two stories, amplify the seismic forces in the bracing and columns by the factor

*C*/2, but not less than 1.5.

_{d}All the diagonal braces frame into the beam-column joints concentrically.

For conforming buildings, the evaluator may consider this condition as mitigated, and no calculations are necessary. The deficiency is in the strength of the joints. Evaluate the consequence of the eccentricity on the member required to resist it. Evaluate the shear, bending and axial force requirements at the locations of eccentricities.

All the brace connections are able to develop the yield capacity of the diagonals.

The deficiency is in the strength of the connections. Check the connection strength. Use a demand value that develops the tensile capacity of the brace or is 1.25 times the required seismic force. If connections in a conforming building cannot develop the yield capacity of the brace and do not meet the requirements of Part 2, Title 24, Section 2211A.9.3 of 1995 *California Building Code* (CBC) or equivalent provision in later version of the CBC, the building shall be placed in SPC 4.

All column splice details of the braced frames can develop the column yield capacity.

The deficiency is in the strength of the splice. Calculate the adequacy of the splice connection for all expected forces including gravity loads. Amplify the seismic load for partial penetration welded splices by the factor *C _{d}*/2 when the seismic load produces tension at the splice. If the column splice details in a conforming building cannot develop the yield capacity of the column and do not meet the requirements of Part 2, Title 24, Section 2211A.9.5 of 1995

*California Building Code*(CBC) or equivalent provision in later version of the CBC, the building shall be placed in SPC 4.

None of the braces in the framing system are of reinforced concrete construction.

The deficiency is in the ductility of the braced frame. Report this condition as a deficiency, and place nonconforming buildings in SPC 1. Place conforming buildings in SPC 4.

### Related Code Sections

*braced*

*frames*. If the average ...

*braced*

*frames*. If the average ...

*braces*in the

*framing*system are of reinforced concrete construction. The deficiency is in the ductility of the

*braced*

*frame*. Report ...

*braces*are not used as the primary diagonal

*bracing*elements in structures over two stories in height. The deficiency ...

*braces*are not used as the primary diagonal

*bracing*elements in structures over two stories in height. The deficiency ...