• Codes
  • Features

    Features Overview

    Go to features
    Reference

    Reference.

    A reliable and up-to-date source of codes.
    Research

    Research.

    Rapidly and efficiently calculate project parameters.
    Collaboration

    Collaboration.

    Get everyone on the same page and streamline code research.
    Workflows
    Architects General Contractor Building Official & Plans Examiner Inspectors Owner Subcontractors Code Consultants
  • Pricing
  • Login
  • Sign Up
Sign Up
Login
  • Code Library
  • Features
  • Pricing
  • About
  • Careers
  • Help
  • Contact
  • Terms
  • Privacy
Sign Up
Upgrade to Premium
Code calculators: Code Calculators automatically generates a detailed list of requirements.
REFERENCE
Amendment Styling
Industry-leading search
Suggested code sections
Code diagrams
RESEARCH
Code calculators
Filter by topic
Code compare
Code sheet exports
COLLABORATION
Team projects
Bookmarks
Comments
START 2 WEEK FREE TRIAL
Have an account? Sign in
// CODE SNIPPET

43-61 Bulk Regulations for Residential Uses in M1-1D Through M1-5D Districts

NYC Zoning Resolution > IV Manufacturing District Regulations > 3 - Bulk Regulations > 43-60 Supplementary Regulations > 43-61 Bulk Regulations for Residential Uses in M1-1D Through M1-5D Districts
JUMP TO FULL CODE CHAPTER

The following regulations shall apply to any development or enlargement authorized pursuant to Section 42-47 (Residential Uses in M1-1D Through M1-5D Districts):

(a)        The total amount of residential floor area permitted on any zoning lot shall not exceed a floor area ratio of 1.65.

On zoning lots containing both residential use and community facility, manufacturing or commercial use, the maximum floor area shall be the maximum floor area permitted for either the commercial or manufacturing use as set forth in Sections 43-12 (Maximum Floor Area Ratio) through 43-14 (Floor Area Bonus for Arcades), or the community facility use as set forth in Section 43-122 (Maximum floor area ratio for community facilities), or the residential use as set forth in this Section, whichever permits the greatest amount of floor area.

On zoning lots containing both residential use and manufacturing or commercial use, the total floor area used for manufacturing or commercial use shall not exceed the amount permitted by Sections 43-12 through 43-14.

(b)        The maximum number of dwelling units shall equal the total residential floor area provided on the zoning lot divided by 675. Fractions equal to or greater than three quarters resulting from this calculation shall be considered to be one dwelling unit.

(c)        The maximum building height above curb level shall be 32 feet.

(d)        No such development or enlargement shall be permitted within 30 feet of the rear lot line.

(e)        The maximum distance from the street line to the street wall of such development shall be ten feet, unless modified by the City Planning Commission pursuant to Section 44-28 (Parking Regulations for Residential Uses in M1-1D Through M1-5D Districts).

(f)        No side yards shall be required. However, if any open area extending along a side lot line is provided at any level it shall have a width of not less than eight feet. However, enlargements of single-family or two-family residences existing as of June 20, 1988, shall be exempt from this requirement, provided such enlarged building does not exceed a height of two stories.

Related Code Sections


1615.1.3 Structural Design, Design Spectral Response Acceleration Parameters
                    (Equation 16-40) where: S D1 = (2/3) S M1 ...
NYC Building Code 2008 > 16 Structural Design > 1615 Earthquake Loads — Site Ground Motion > 1615.1 General Procedure for Determining Maximum Considered Earthquake and Design Spectral Response Accelerations > 1615.1.3 Design Spectral Response Acceleration Parameters
Article 8 Materials, Loads and Stresses [PDF] (page 20)
or girder, the 1/10 reduction may be used in proportioning the column for the combined axial and bending loading, provided that the unit stress fa, due to any ...
NYC 1938 Code [PDF] > 8 Materials, Loads and Stresses
1613.5.4 Structural Design, Design Spectral Response Acceleration Parameters
as determined in Section 1613.5.3. S M1 = The MCE R spectral response accelerations for 1-second period as determined in Section 1613.5.3 ...
NYC Building Code 2014 > 16 Structural Design > 1613 Earthquake Loads > 1613.5 Seismic Ground Motion Values > 1613.5.4 Design Spectral Response Acceleration Parameters
Article 8 Materials, Loads and Stresses [PDF] (page 21)
their supports in the plane of bending. M Cm = 0.6 + 0.4M1 , but not less than 0.4 2 where M1 / M2 is the ratio of the smaller to larger moments ...
NYC 1938 Code [PDF] > 8 Materials, Loads and Stresses
1620.4.5 Structural Design, Building Separations
on the same property shall be separated by at least δ MT where δMT = √( δ M1 ) 2 + ( δ M2 ) 2 ...
NYC Building Code 2008 > 16 Structural Design > 1620 Earthquake Loads — Design, Detailing Requirements and Structural Component Load Effects > 1620.4 Seismic Design Category D > 1620.4.5 Building Separations
Help Contact Us Privacy Terms
Code Compare
Code Compare
Highlight differences between any two building codes.
Search
Search
Don't miss relevant code. Quickly locate sections across your jurisdiction.
View thousands of relevant UL Certified products and assemblies that help achieve code compliance
View thousands of relevant UL Certified products and assemblies that help achieve code compliance
Access to UL product and system certification information.
Code sheet exports
Code sheet exports
Generate a code sheet that integrates with your drawing set.
Code Calculators
Code Calculators
Code calculators automatically generate a detailed list of requirements.
Code diagrams
Code diagrams
Unpack the code through illustrations and descriptions.
Shared projects
Shared projects
Projects provide a dedicated space to collaborate on code research.
UpCodes Premium
Leverage the most sophisticated code compliance platform.
TRY FREE FOR TWO WEEKS VISIT PRICING
Join the waitlist
We are looking to gauge the level of interest in linking UL product and system certification information alongside related code sections.

Let us know your email and we’ll ping you once it’s ready! Learn more.

Thank you for your interest!

If you’re open to it, we would love to jump on the phone to make sure we’re building this in the best way possible for your workflow. Any insight or advice would be greatly appreciated. We’ve sent you an email with a calendar link to book at time with us.


Cancel
Get Early Access
UpCodes Premium
Leverage the full code compliance platform.
START 2 WEEK FREE TRIAL LEARN MORE