3501.3 Building Code Referenced Standards
AA
Standard reference number | Title | Referenced in code section number |
ADM1—10
Aluminum Design Manual: Part 1-A Specification for Aluminum Structures, Allowable Stress Design;
and Part 1-B—Aluminum Structures, Load and Resistance Factor Design
ASM 35—00
Aluminum Sheet Metal Work in Building Construction (Fourth Edition)
AAMA
Standard reference number | Title | Referenced in code section number |
1402—09
Standard Specifications for Aluminum Siding, Soffit and Fascia
AAMA/WDMA/CSA 101/I.S.2/A440—08
North American Fenestration Standard/Specifications for Windows, Doors and Skylights
ACI
Standard reference number | Title | Referenced in code section number |
216.1—07
Standard Method for Determining Fire Resistance of Concrete and Masonry Construction Assemblies
318—08
Building Code Requirements for Structural Concrete
530—08
Building Code Requirements for Masonry Structures
530.1—08
Specifications for Masonry Structures
AF&PA
Standard reference number | Title | Referenced in code section number |
WCD No. 4—03
Wood Construction Data—Plank and Beam Framing for Residential Buildings
NDS—05
National Design Specification (NDS) for Wood Construction with 2005 Supplement
AF&PA—93
Span Tables for Joists and Rafters
ANSI/AF&PA PWF—07
Permanent Wood Foundation Design Specification
ANSI/AF&PA SDPWS—08
Special Design Provisions for Wind and Seismic
AISC
Standard reference number | Title | Referenced in code section number |
341—05
Seismic Provisions for Structural Steel Buildings, including Supplement No. 1 dated 2005
360—05
Specification for Structural Steel Buildings
AISI
Washington
Standard reference number | Title | Referenced in code section number |
S100—07
North American Specification for the Design of Cold-formed Steel Structural Members
S200—08
North American Standard for Cold-formed Steel Framing—General Provisions
S210—08
North American Standard for Cold-formed Steel Framing—Floor and Roof System Design
S211—08
North American Standard for Cold-formed Steel Framing—Wall Stud Design
S212—08
North American Standard for Cold-formed Steel Framing—Header Design
S213—08
North American Standard for Cold-formed Steel Framing—Lateral Design
S214—08
North American Standard for Cold-formed Steel Framing—Truss Design, with Supplement 2, dated 2008
AITC
Englewood
Standard reference number | Title | Referenced in code section number |
AITC Technical
Note 7—96
Calculation of Fire Resistance of Glued Laminated Timbers
AITC 104—03
Typical Construction Details
AITC 110—01
Standard Appearance Grades for Structural Glued Laminated Timber
AITC 113—01
Standard for Dimensions of Structural Glued Laminated Timber
AITC 117—04
Standard Specifications for Structural Glued Laminated Timber of Softwood Species
AITC 119—96
Standard Specifications for Structural Glued Laminated Timber of Hardwood Species
AITC 200—09
Manufacturing Quality Control Systems Manual for Structural Glued Laminated Timber
ANSI/AITC A 190.1—07
Structural Glued Laminated Timber
ALI
Standard reference number | Title | Referenced in code section number |
ALI ALCTV—2007
Standard for Automobile Lifts—Safety Requirements for Construction, Testing and Validation (ANSI)
ANSI
Standard reference number | Title | Referenced in code section number |
A13.1—07
(Reaffirmed 2002)
Scheme for the Identification of Piping Systems
A108.1A—09
Installation of Ceramic Tile in the Wet-set Method, with Portland Cement Mortar
A108.1B—09
Installation of Ceramic Tile, quarry Tile on a Cured Portland Cement Mortar Setting
Bed with Dry-set or Latex-portland Mortar
A108.4—09
Installation of Ceramic Tile with Organic Adhesives or Water-cleanable Tile-setting Epoxy Adhesive
A108.5—09
Installation of Ceramic Tile with Dry-set Portland Cement Mortar or Latex-portland Cement Mortar
A108.6—09
Installation of Ceramic Tile with Chemical-resistant,Water Cleanable Tile-setting and -grouting Epoxy
A108.8—09
Installation of Ceramic Tile with Chemical-resistant Furan Resin Mortar and Grout
A108.9—09
Installation of Ceramic Tile with Modified Epoxy Emulsion Mortar/Grout
A108.10—09
Installation of Grout in Tilework
A118.1—10.1
American National Standard Specifications for Dry-set Portland Cement Mortar
A118.3—10.1
American National Standard Specifications for Chemical-resistant, Water-cleanable Tile-setting and
-grouting Epoxy and Water Cleanable Tile-setting Epoxy Adhesive
A118.4—10.1
American National Standard Specifications for Latex-portland Cement Mortar
A118.5—10.1
American National Standard Specifications for Chemical Resistant Furan Mortar and Grouts for Tile Installation
A118.6—10.1
American National Standard Specifications for Cement Grouts for Tile Installation
A118.8—10.1
American National Standard Specifications for Modified Epoxy Emulsion Mortar/Grout
A136.1—10.1
American National Standard Specifications for Organic Adhesives for Installation of Ceramic Tile
A137.1—08
American National Standard Specifications for Ceramic Tile
A208.1—09
Particleboard
Z 97.1—09
Safety Glazing Materials Used in Buildings—Safety Performance Specifications and Methods of Test
APA
Standard reference number | Title | Referenced in code section number |
APA PDS—08
Panel Design Specification
APA PDS Supplement 1—90
Design and Fabrication of Plywood Curved Panels (revised 1995)
APA PDS Supplement 2—92
Design and Fabrication of Plywood-lumber Beams (revised 1998)
APA PDS Supplement 3—96
Design and Fabrication of Plywood Stressed-skin Panels (revised 1996)
APA PDS Supplement 4—93
Design and Fabrication of Plywood Sandwich Panels (revised 1993)
APA PDS Supplement 5—95
Design and Fabrication of All-plywood Beams (revised 1995)
EWS R540—07
Builders Tips: Proper Storage and Handling of Glulam Beams
EWS S475—07
Glued Laminated Beam Design Tables
EWS S560—10
Field Notching and Drilling of Glued Laminated Timber Beams
EWS T300—077
Glulam Connection Details
EWS X440—08
Product Guide—Glulam
EWS X450—01
Glulam in Residential Construction—Western Edition
APSP
Standard reference number | Title | Referenced in code section number |
ANSI/APSP 7—06
Standard for Suction Entrapment Avoidance in Swimming Pools, Wading Pools, Spas, Hot Tubs and Catch Basins
ASABE
Standard reference number | Title | Referenced in code section number |
EP 484.2—98
Diaphragm Design of Metal-clad, Post-frame Rectangular Buildings
EP 486.1—99
Shallow-post Foundation Design
EP 559—03
Design Requirements and Bending Properties for Mechanically Laminated Columns
ASCE/SEI
Reston
Standard reference number | Title | Referenced in code section number |
3—91
Structural Design of Composite Slabs
5—08
Building Code Requirements for Masonry Structures
6—08
Specification for Masonry Structures
7—05
Minimum Design Loads for Buildings and Other Structures including Supplements No. 1 and 2, excluding Chapter 14 and Appendix 11A
8—02
Standard Specification for the Design of Cold-formed Stainless Steel Structural Members
19—10
Structural Applications of Steel Cables for Buildings
24—05
Flood Resistant Design and Construction
29—05
Standard Calculation Methods for Structural Fire Protection
32—01
Design and Construction of Frost Protected Shallow Foundations
ASHRAE
Standard reference number | Title | Referenced in code section number |
ASHRAE 90.1—2007
Energy Standard for Buildings Except Low-Rise Residential Buildings
ASME
Standard reference number | Title | Referenced in code section number |
A17.1/CSA B44—2010
Safety Code for Elevators and Escalators
A18.1—2008
Safety Standard for Platform Lifts and Stairway Chairlifts
A90.1—2009
Safety Standard for Belt Manlifts
B16.18—2001
(Reaffirmed 2005)
Cast Copper Alloy Solder Joint Pressure Fittings
B16.22—2001
(Reaffirmed 2005)
Wrought Copper and Copper Alloy Solder Joint Pressure Fittings
B20.1—2009
Safety Standard for Conveyors and Related Equipment
B31.3—2008
ASTM
Standard reference number | Title | Referenced in code section number |
A 36/A 36M—08
Specification for Carbon Structural Steel
A 153/A 153M—09
Specification for Zinc Coating (Hot-dip) on Iron and Steel Hardware
A 240/A 240M—10a
Standard Specification for Chromium and Chromium-nickel Stainless Steel Plate,
Sheet and Strip for Pressure Vessels and for General Applications
A 252—10
Specification for Welded and Seamless Steel Pipe Piles
A 283/A 283M—03 (2007)
Specification for Low and Intermediate Tensile Strength Carbon Steel Plates
A 307—07b
Specification for Carbon Steel Bolts and Studs, 60,000 psi Tensile Strength
A 416/A 416M—10
Specification for Steel Strand, Uncoated Seven-wire for Prestressed Concrete
A 463/A 463M—09a
Standard Specification for Steel Sheet, Aluminum-coated, by the Hot-dip Process
A 572/A 572M—07
Specification for High-strength Low-alloy Columbium-vanadium Structural Steel
A 588/A 588M—10
Specification for High-strength Low-alloy Structural Steel with 50 ksi (345 MPa)
Minimum Yield Point to 4 inches (100 mm) Thick
A 615/A 615M—09b
Specification for Deformed and Plain Billet-steel Bars for Concrete Reinforcement
A 653/A 653M—09a
Specification for Steel Sheet, Zinc-coated Galvanized or Zinc-iron Alloy-coated Galvannealed by the Hot-dip Process
A 690/A 690M—07
Standard Specification for High-strength Low-alloy Nickel, Copper, Phosphorus Steel H-piles and Sheet Piling with Atmospheric Corrosion Resistance for Use in Marine Environments
A 706/A 706M—09b
Specification for Low-alloy Steel Deformed and Plain Bars for Concrete Reinforcement
A 722/A 722M—07
Specification for Uncoated High-strength Steel Bar for Prestressing Concrete
A 755/A 755M—03 (2008)
Specification for Steel Sheet, Metallic-coated by the Hot-dip Process and Prepainted by the Coil-coating Process for Exterior Exposed Building Products
A 792/A 792M—09a
Specification for Steel Sheet, 55% Aluminum-zinc Alloy-coated by the Hot-dip Process
A 875/A 875M—09a
Standard Specification for Steel Sheet Zinc-5 percent, Aluminum Alloy-coated by the Hot-dip Process
A 913/A 913M—07
Specification for High-strength Low-alloy Steel Shapes of Structural Quality, Produced by Quenching and Self-tempering Process (QST)
A 924/A 924M—10
Standard Specification for General Requirements for Steel Sheet, Metallic-coated by the Hot-dip Process
A 992/A 992M—06a
Standard Specification for Structural Shapes
B 42—10
Specification for Seamless Copper Pipe, Standard Sizes
B 43—09
Specification for Seamless Red Brass Pipe, Standard Sizes
B 68—02
Specification for Seamless Copper Tube, Bright Annealed (Metric)
B 88—09
Specification for Seamless Copper Water Tube
B 101—07
Specification for Lead-coated Copper Sheet and Strip for Building Construction
B 209—07
Specification for Aluminum and Aluminum Alloy Steel and Plate
B 251—10
Specification for General Requirements for Wrought Seamless Copper and Copper-alloy Tube
B 280—08
Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service
B 370—09
Specification for Cold-rolled Copper Sheet and Strip for Building Construction
B 695—04 (2009)
Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
C 5—10
Specification for Quicklime for Structural Purposes
C 22/C 22M—00 (2005)e01
Specification for Gypsum
C 27—98 (2008)
Specification for Standard Classification of Fireclay and High-alumina Refractory Brick
C 28/C 28M—10
Specification for Gypsum Plasters
C 31/C 31M—10
Practice for Making and Curing Concrete Test Specimens in the Field
C 33—08
Specification for Concrete Aggregates
C 34—10
Specification for Structural Clay Load-bearing Wall Tile
C 35—01 (2009)
Specification for Inorganic Aggregates for Use in Gypsum Plaster
C 36/C 36M—03
Specification for Gypsum Wallboard
C 37/C 37M—01
Specification for Gypsum Lath
C 55—09
Specification for Concrete Building Brick
C 56—10
Specification for Structural Clay Nonload Bearing Tile
C 59/C 59M—00 (2006)
Specification for Gypsum Casting and Molding Plaster
C 61/C 61M—00 (2006)
Specification for Gypsum Keene's Cement
C 62—10
Specification for Building Brick (Solid Masonry Units Made from Clay or Shale)
C 67—09
Test Methods of Sampling and Testing Brick and Structural Clay Tile
C 73—05
Specification for Calcium Silicate Face Brick (Sand-lime Brick)
C 79—04a
Specification for Treated Core and Nontreated Core Gypsum Sheathing Board
C 90—09
Specification for Loadbearing Concrete Masonry Units
C 91—05
Specification for Masonry Cement
C 94/C 94M—10
Specification for Ready-mixed Concrete
C 126—10
Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick and Solid Masonry Units
C 140—10
Test Method Sampling and Testing Concrete Masonry Units and Related Units
C 150—09
Specification for Portland Cement
C 172—10
Practice for Sampling Freshly Mixed Concrete
C 199—84 (2005)
Test Method for Pier Test for Refractory Mortars
C 206—03 (2009)
Specification for Finishing Hydrated Lime
C 208—08a
Specification for Cellulosic Fiber Insulating Board
C 212—10
Specification for Structural Clay Facing Tile
C 216—10
Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)
C 270—10
Specification for Mortar for Unit Masonry
C 315—07
Specification for Clay Flue Liners and Chimney Pots
C 317/C 317M—00 (2005)
Specification for Gypsum Concrete
C 330—09
Specification for Lightweight Aggregates for Structural Concrete
C 331—05
Specification for Lightweight Aggregates for Concrete Masonry Units
C 406—10
Specification for Roofing Slate
C 442/C 442M—04
Specification for Gypsum Backing Board and Coreboard and Gypsum Shaftliner Board
C 472—99 (2009)
Specification for Standard Test Methods for Physical Testing of Gypsum, Gypsum Plasters and Gypsum Concrete
C 473—10
Test Method for Physical Testing of Gypsum Panel Products
C 474—05
Test Methods for Joint Treatment Materials for Gypsum Board Construction
C 475—02 (2007)
Specification for Joint Compound and Joint Tape for Finishing Gypsum Wallboard
C 503—10
Specification for Marble Dimension Stone (Exterior)
C 514—04 (2009)e1
Specification for Nails for the Application of Gypsum Board
C 516—08
Specifications for Vermiculite Loose Fill Thermal Insulation
C 547—07e1
Specification for Mineral Fiber Pipe Insulation
C 549—06
Specification for Perlite Loose Fill Insulation
C 552—07
Standard Specification for Cellular Glass Thermal Insulation
C 557—03 (2009)e01
Specification for Adhesives for Fastening Gypsum Wallboard to Wood Framing
C 568—10
Specification for Limestone Dimension Stone
C 578—10
Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation
C 587—04 (2009)
Specification for Gypsum Veneer Plaster
C 588/C 588M—01
Specification for Gypsum Base for Veneer Plasters
C 595—10
Specification for Blended Hydraulic Cements
C 615—10
Specification for Granite Dimension Stone
C 616—10
Specification for Quartz Dimension Stone
C 629—10
Specification for Slate Dimension Stone
C 630/C 630M—03
Specification for Water-resistant Gypsum Backing Board
C 631—09
Specification for Bonding Compounds for Interior Gypsum Plastering
C 635/C 636M—08
Specification for the Manufacture, Performance and Testing of Metal Suspension
Systems for Acoustical Tile and Lay-in Panel Ceilings
C 636/C 636M—08
Practice for Installation of Metal Ceiling Suspension Systems for Acoustical Tile and Lay-in Panels
C 645—09a
Specification for Nonstructural Steel Framing Members
C 652—10
Specification for Hollow Brick (Hollow Masonry Units Made from Clay or Shale)
C 728—05 (2010)
Standard Specification for Perlite Thermal Insulation Board
C 744—10
Specification for Prefaced Concrete and Calcium Silicate Masonry Units
C 754—09a
Specification for Installation of Steel Framing Members to Receive Screw-attached Gypsum Panel Products
C 836/C 836M—10
Specification for High-solids Content, Cold Liquid-applied Elastomeric
Waterproofing Membrane for Use with Separate Wearing Course
C 840—08
Specification for Application and Finishing of Gypsum Board
C 841—03 (2008)e1
Specification for Installation of Interior Lathing and Furring
C 842—05
Specification for Application of Interior Gypsum Plaster
C 843—99 (2006)
Specification for Application of Gypsum Veneer Plaster
C 844—10
Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster
C 847—10a
Specification for Metal Lath
C 887—05 (2010)
Specification for Packaged, Dry Combined Materials for Surface Bonding Mortar
C 897—05 (2009)
Specification for Aggregate for Job-mixed Portland Cement-based Plaster
C 920—10
Standard for Specification for Elastomeric Joint Sealants
C 926—06
Specification for Application of Portland Cement-based Plaster
C 931/C 931M—04
Specification for Exterior Gypsum Soffit Board
C 932—06
Specification for Surface-applied Bonding Compounds Agents for Exterior Plastering
C 933—09
Specification for Welded Wire Lath
C 946—10
Specification for Practice for Construction of Dry-stacked, Surface-bonded Walls
C 954—10
Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to
Steel Studs from 0.033 inch (0.84 mm) to 0.112 inch (2.84 mm) in Thickness
C 955—09a
Standard Specification for Load-bearing Transverse and Axial Steel Studs, Runners Tracks, and Bracing or Bridging, for Screw Application of Gypsum Panel Products and Metal Plaster Bases
C 956—04 (2010)
Specification for Installation of Cast-in-place Reinforced Gypsum Concrete
C 957—10
Specification for High-solids Content, Cold Liquid-applied Elastomeric
Waterproofing Membrane with Integral Wearing Surface
C 960—04
Specification for Predecorated Gypsum Board
C 1002—07
Specification for Steel Self-piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs
C 1007—08a
Specification for Installation of Load Bearing (Transverse and Axial) Steel Studs and Related Accessories
C 1019—09
Test Method of Sampling and Testing Grout
C 1029—10
Specification for Spray-applied Rigid Cellular Polyurethane Thermal Insulation
C 1032—06
Specification for Woven Wire Plaster Base
C 1047—10a
Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base
C 1063—08
Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-based Plaster
C 1088—10
Specification for Thin Veneer Brick Units Made from Clay or Shale
C 1167—03 (2009)
Specification for Clay Roof Tiles
C 1177/C 1177M—08
Specification for Glass Mat Gypsum Substrate for Use as Sheathing
C 1178/C 1178M—08
Specification for Coated Mat Water-resistant Gypsum Backing Panel
C 1186—08
Specification for Flat Nonasbestos Fiber Cement Sheets
C 1261—10
Specification for Firebox Brick for Residential Fireplaces
C 1278/C 1278M—07a
Specification for Fiber-reinforced Gypsum Panels
C 1280—09
Specification for Application of Gypsum Sheathing
C 1283—07a
Practice for Installing Clay Flue Lining
C 1288—99 (2010)
Standard Specification for Discrete Nonasbestos Fiber-cement Interior Substrate Sheets
C 1289—10
Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board
C 1314—10
Test Method for Compressive Strength of Masonry Prisms
C 1325—08b
Standard Specification for Nonasbestos Fiber-mat Reinforced Cement Interior Substrate Sheets
C 1328—05
Specification for Plastic (Stucco Cement)
C 1386—07
Specification for Precast Autoclaved Aerated Concrete (AAC) Wall Construction Units
C 1395/C 1395M—06a
Specification for Gypsum Ceiling Board
C 1396—09a
Specification for Gypsum Board
C 1405—10
Standard Specification for Glazed Brick (Single Fired, Solid Brick Units)
C 1492—03 (2009)
Standard Specification for Concrete Roof Tile
C 1629/C 1629M—06
Standard Classification for Abuse-resistant Nondecorated Interior Gypsum Panel Products and Fiber-reinforced Cement Panels
C 1658/C 1658M—06
Standard Specification for Glass Mat Gypsum Panels
D 25—99 (2005)
Specification for Round Timber Piles
D 41—05 (2010)
Specification for Asphalt Primer Used in Roofing, Dampproofing and Waterproofing
D 43—00 (2006)
Specification for Coal Tar Primer Used in Roofing, Dampproofing and Waterproofing
D 56—05
Test Method for Flash Point By Tag Closed Tester
D 86—10a
Test Method for Distillation of Petroleum Products at Atmospheric Pressure
D 93—10
Test Method for Flash Point By Pensky-Martens Closed Cup Tester
D 225—07
Specification for Asphalt Shingles (Organic Felt) Surfaced with Mineral Granules
D 226/D 226M—09
Specification for Asphalt-saturated Organic Felt Used in Roofing and Waterproofing
D 227—03
Specification for Coal-tar-saturated Organic Felt Used in Roofing and Waterproofing
D 312—00 (2006)
Specification for Asphalt Used in Roofing
D 422—63 (2007)
Test Method for Particle-size Analysis of Soils
D 448—08
Standard Classification for Sizes of Aggregate for Road and Bridge Construction
D 450—07
Specification for Coal-tar Pitch Used in Roofing, Dampproofing and Waterproofing
D 635—10
Test Method for Rate of Burning and/or Extent and Time of Burning of Self-supporting Plastics in a Horizontal Position
D 1143/D 1143M—07e1
Test Method for Piles Under Static Axial Compressive Load
D 1227—95 (2007)
Specification for Emulsified Asphalt Used as a Protective Coating for Roofing
D 1557—09
Test Method for Laboratory Compaction Characteristics of Soil Using Modified Effort [56,000 ft-lb/ft3 (2,700 KN m/m3)]
D 1586—08a
Specification for Penetration Test and Split-barrel Sampling of Soils
D 1761—06
Test Method for Mechanical Fasteners in Wood
D 1863—05
Specification for Mineral Aggregate Used on Built-up Roofs
D 1929—96 (2001)e01
Test Method for Determining Ignition Properties of Plastics
D 1970—09
Specification for Self-adhering Polymer Modified Bituminous Sheet Materials
Used as Steep Roof Underlayment for Ice Dam Protection
D 2166—06
Test Method for Unconfined Compressive Strength of Cohesive Soil
D 2178—04
Specification for Asphalt Glass Felt Used in Roofing and Waterproofing
D 2216—10
Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
D 2487—10
Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
D 2626—04
Specification for Asphalt Saturated and Coated Organic Felt Base Sheet Used in Roofing
D 2822—05
Specification for Asphalt Roof Cement
D 2823—05
Specification for Asphalt Roof Coatings
D 2843—10
Test for Density of Smoke from the Burning or Decomposition of Plastics
D 2850—03a (2007)
Test Method for Unconsolidated, Undrained Triaxial Compression Test on Cohesive Soils
D 2898—10
Test Methods for Accelerated Weathering of Fire-retardant-treated Wood for Fire Testing
D 3019—08
Specification for Lap Cement Used with Asphalt Roll Roofing, Nonfibered, Asbestos Fibered and Nonasbestos Fibered
D 3161—09
Test Method for a Wind Resistance of Asphalt Shingles (Fan Induced Method)
D 3200—74 (2005)
Standard Specification and Test Method for Establishing Recommended Design Stresses for Round Timber Construction Poles
D 3201—08ae1
Test Method for Hygroscopic Properties of Fire-retardant-treated Wood and Wood-based Products
D 3278—96 (2004)e01
Test Methods for Flash Point of Liquids by Small Scale Closed-cup Apparatus
D 3462/D 3462M—10a
Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules
D 3468—99 (2006)e01
Specification for Liquid-applied Neoprene and Chlorosulfonated Polyethylene Used in Roofing and Waterproofing
D 3679—09a
Specification for Rigid Poly [Vinyl Chloride (PVC) Siding]
D 3689—07
Method for Testing Individual Piles Under Static Axial Tensile Load
D 3737—09
Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)
D 3746—85 (2008)
Test Method for Impact Resistance of Bituminous Roofing Systems
D 3747—79 (2007)
Specification for Emulsified Asphalt Adhesive for Adhering Roof Insulation
D 3909—97b (2004)e01
Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules
D 3957—09
Standard Practices for Establishing Stress Grades for Structural Members Used in Log Buildings
D 4022—07
Specification for Coal Tar Roof Cement, Asbestos Containing
D 4272—09
Test Method for Total Energy Impact of Plastic Films by Dart Drop
D 4318—10
Test Methods for Liquid Limit, Plastic Limit and Plasticity Index of Soils
D 4434/D 4434 M—09
Specification for Poly (Vinyl Chloride) Sheet Roofing
D 4479—07
Specification for Asphalt Roof Coatings—Asbestos-free
D 4586—07
Specification for Asphalt Roof Cement—Asbestos-free
D 4601—04
Specification for Asphalt-coated Glass Fiber Base Sheet Used in Roofing
D 4637/D 463 M—10
Specification for EPDM Sheet Used in Single-ply Roof Membrane
D 4829—08a
Test Method for Expansion Index of Soils
D 4869—05e01
Specification for Asphalt-saturated (Organic Felt) Underlayment Used in Steep Slope Roofing
D 4897/D 4897 M—01 (2009)
Specification for Asphalt-coated Glass Fiber Venting Base Sheet Used in Roofing
D 4945—08
Test Method for High-strain Dynamic Testing of Piles
D 4990—97a (2005)e01
Specification for Coal Tar Glass Felt Used in Roofing and Waterproofing
D 5019—07a
Specification for Reinforced Nonvulcanized Polymeric Sheet Used in Roofing Membrane
D 5055—10
Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-joists
D 5456—10
Specification for Evaluation of Structural Composite Lumber Products
D 5516—09
Test Method of Evaluating the Flexural Properties of Fire-retardant-treated
Softwood Plywood Exposed to the Elevated Temperatures
D 5643—06
Specification for Coal Tar Roof Cement, Asbestos-free
D 5664—10
Test Methods for Evaluating the Effects of Fire-retardant Treatment and
Elevated Temperatures on Strength Properties of Fire-retardant-treated Lumber
D 5665—99a (2006)
Specification for Thermoplastic Fabrics Used in Cold-applied Roofing and Waterproofing
D 5726—98 (2005)
Specification for Thermoplastic Fabrics Used in Hot-applied Roofing and Waterproofing
D 6083—05e01
Specification for Liquid Applied Acrylic Coating Used in Roofing
D 6162—00a (2008)
Specification for Styrene-butadiene-styrene (SBS) Modified Bituminous
Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements
D 6163—00 (2008)
Specification for Styrene-butadiene-styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements
D 6164—05e1
Specification for Styrene-butadiene-styrene (SBS) Modified Bituminous Sheet Metal Materials Using Polyester Reinforcements
D 6222—08
Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements
D 6223/D 6223M—02 (2009)e1
Specification for Atactic Polypropylene (APP) Modified Bituminous
Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements
D 6298—05e1
Specification for Fiberglass Reinforced Styrene-butadiene-styrene (SBS)
Modified Bituminous Sheets with a Factory Applied Metal Surface
D 6305—08
Practice for Calculating Bending Strength Design Adjustment Factors for Fire-retardant-treated Plywood Roof Sheathing
D 6380—03 (2009)
Standard Specification for Asphalt Roll Roofing (Organic) Felt
D 6509/D 6509M—09
Standard Specification for Atactic Polypropylene (APP) Modified Bituminous base
Sheet Materials Using Glass Fiber Reinforcements
D 6694—08
Standard Specification for Liquid-applied Silicone Coating Used in Spray Polyurethane Foam Roofing
D 6754/D 6754M—10
Standard Specification for Ketone Ethylene Ester Based Sheet Roofing
D 6757—07
Standard Specification for Inorganic Underlayment for Use with Steep Slope Roofing Products
D 6841—08
Standard Practice for Calculating Design Value Treatment Adjustment Factors for Fire-retardant-treated Lumber
D 6878—08e1
Standard Specification for Thermoplastic Polyolefin Based Sheet Roofing
D 6947—07
Standard Specification for Liquuid Applied Moisture Cured Polyurethane Coating
Used in Spray Polyurethane Foam Roofing System
D 7158—08d
Standard Test Method for Wind Resistance of Sealed Asphalt Shingles (Uplift Force/Uplift Resistance Method)
E 84—10b
Test Methods for Surface Burning Characteristics of Building Materials
E 90—09
Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements
E 96/E 96M—05
Test Method for Water Vapor Transmission of Materials
E 108—10a
Test Methods for Fire Tests of Roof Coverings
E 119—10b
Test Methods for Fire Tests of Building Construction and Materials
E 136—09b
Test Method for Behavior of Materials in a Vertical Tube Furnace at 750°C
E 330—02 (2010)
Test Method for Structural Performance of Exterior Windows, Curtain Walls and Doors by Uniform Static Air Pressure Difference
E 331—00 (2009)
Test Method for Water Penetration of Exterior Windows, Skylights, Doors and Curtain Walls by Uniform Static Air Pressure Difference
E 492—09
Test Method for Laboratory Measurement of Impact Sound Transmission Through Floor-ceiling Assemblies Using the Tapping Machine
E 605—93 (2006)
Test Method for Thickness and Density of Sprayed Fire-resistive Material (SFRM) Applied to Structural Members
E 681—09
Test Methods for Concentration Limits of Flammability of Chemical Vapors and Gases
E 736—00 (2006)
Test Method for Cohesion/Adhesion of Sprayed Fire-resistive Materials Applied to Structural Members
E 814—10
Test Method of Fire Tests of Through-penetration Firestops
E 970—10
Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source
E 1300—09a
Practice for Determining Load Resistance of Glass in Buildings
E 1354—10a
Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products
Using an Oxygen Consumption Calorimeter
E 1592—05
Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference
E 1602—03 (2010)e1
Guide for Construction of Solid Fuel-burning Masonry Heaters
E 1886—05
Test Method for Performance of Exterior Windows, Curtain Walls, Doors and
Storm Shutters Impacted by Missiles and Exposed to Cyclic Pressure Differentials
E 1966—07
Test Method for Fire-resistant Joint Systems
E 1996—09
Specification for Performance of Exterior Windows, Glazed Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
E 2072—10
Standard Specification for Photoluminescent (Phosphorescent) Safety Markings
E 2273—03
Standard Test Method for Determining the Drainage Efficiency of Exterior Insulation and Finish Systems (EIFS) Clad Wall Assemblies
E 2307—10
Standard Test Method for Determining Fire Resistance of Perimeter Fire Barrier Systems
Using Intermediate-scale, Multistory Test Apparatus
E 2404—10
Standard Practice for Specimen Preparation and Mounting of Textile, Paper or Vinyl Wall or
Ceiling Coverings to Assess Surface Burning Characteristics
E 2568—09e1
Standard Specification for PB Exterior Insulation and Finish Systems (EIFS)
E 2570—07
Standard Test Method for Evaluating Water-resistive Barrier (WRB) Coatings Used Under Exterior Insulation and Finish Systems (EIFS) for EIFS with Drainage
E 2573—07a
Standard Practice for Specimen Preparation and Mounting of Site-fabricated Stretch Systems to Assess Surface Burning Characteristics
F 547—06
Terminology of Nails for Use with Wood and Wood-based Materials
F 1346—91 (2003)
Performance Specification for Safety Covers and Labeling Requirements for All Covers for Swimming Pools, Spas and Hot Tubs
F 1667—10
Specification for Driven Fasteners: Nails, Spikes and Staples
F 2006—10
Standard/Safety Specification for Window Fall Prevention Devices for Nonemergency Escape (Egress) and Rescue (Ingress) Windows
F 2090—10
Specification for Window Fall Prevention Devices with Emergency Escape (Egress) Release Mechanisms
F 2200—05
Standard Specification for Automated Vehicular Gate Construction
G 152—06
Practice for Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials
G 154—06
Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials
G 155—05a
Practice for Operating Xenon Arc Light Apparatus for Exposure of Nonmetallic Materials
AWCI
Standard reference number | Title | Referenced in code section number |
12-B—05
Technical Manual 12-B Standard Practice for the Testing and Inspection of
Field Applied Thin Film Intumescent Fire-resistive Materials; an Annotated Guide, Second Edition
AWPA
Standard reference number | Title | Referenced in code section number |
C1—03
All Timber Products—Preservative Treatment by Pressure Processes
M4—06
Standard for the Care of Preservative-treated Wood Products
U1—10
USE CATEGORY SYSTEM: User Specification for Treated Wood Except Section 6, Commodity Specification H
AWS
Standard reference number | Title | Referenced in code section number |
D1.1—10
Structural Welding Code—Steel
D1.3—08
Structural Welding Code—Sheet Steel
D1.4—05
Structural Welding Code—Reinforcing Steel
BHMA
Standard reference number | Title | Referenced in code section number |
A 156.10—05
Power Operated Pedestrian Doors
A 156.19—07
Standard for Power Assist and Low Energy Operated Doors
CGSB
Gatineau
Standard reference number | Title | Referenced in code section number |
37-GP-52M (1984)
Roofing and Waterproofing Membrane, Sheet Applied, Elastomeric
37-GP-56M (1985)
Membrane, Modified, Bituminous, Prefabricated and Reinforced for Roofing—with December 1985 Amendment
CAN/CGSB 37.54—95
Polyvinyl Chloride Roofing and Waterproofing Membrane
CPA
Standard reference number | Title | Referenced in code section number |
ANSI A135.4—2004
Basic Hardboard
ANSI A135.5—2004
Prefinished Hardboard Paneling
ANSI A135.6—2006
Hardboard Siding
CPSC
Standard reference number | Title | Referenced in code section number |
16 CFR Part 1201(1977)
Safety Standard for Architectural Glazing Material
16 CFR Part 1209 (1979)
Interim Safety Standard for Cellulose Insulation
16 CFR Part 1301 (1977)
Ban of Unstable Refuse Bins
16 CFR Part 1404 (1979)
Cellulose Insulation
16 CFR Part 1500 (1991)
Hazardous Substances and Articles; Administration and Enforcement Regulations
16 CFR Part 1500.44 (2001)
Method for Determining Extremely Flammable and Flammable Solids
16 CFR Part 1507 (2001)
Fireworks Devices
16 CFR Part 1630 (2000)
Standard for the Surface Flammability of Carpets and Rugs
CSA
Standard reference number | Title | Referenced in code section number |
101/I.S.2/A440—08
Specifications for Windows, Doors and Unit Skylights
CSSB
Standard reference number | Title | Referenced in code section number |
CSSB—97
Grading and Packing Rules for Western Red Cedar Shakes and Western Red Shingles
of the Cedar Shake and Shingle Bureau
DASMA
Standard reference number | Title | Referenced in code section number |
ANSI/DASMA 107—1997
(R2004)
Room Fire Test Standard for Garage Doors Using Foam Plastic Insulation
108—05
Standard Method for Testing Sectional Garage Doors and Rolling Doors:
Determination of Structural Performance Under Uniform Static Air Pressure Difference
115—05
Standard Method for Testing Sectional Garage Doors and Rolling Doors:
Determination of Structural Performance Under Missile Impact and Cyclic Wind Pressure
DOC
Washington
Standard reference number | Title | Referenced in code section number |
PS-1—07
Structural Plywood
PS-2—04
Performance Standard for Wood-based Structural-use Panels
PS 20—05
American Softwood Lumber Standard
DOL
Washington
Standard reference number | Title | Referenced in code section number |
29 CFR Part 1910.1000
(1974)
Air Contaminants
DOTn
Standard reference number | Title | Referenced in code section number |
49 CFR Parts 100-185-2005
Hazardous Materials Regulations
49 CFR Parts 173.137 (2005)
Shippers—General Requirements for Shipments and Packaging—Class 8—Assignment of Packing Group
49 CFR—1998
Specification of Transportation of Explosive and Other Dangerous Articles, UN 0335, UN 0336 Shipping Containers
EN
Rue de Stassart 36
B-10 50 Brussels
Standard reference number | Title | Referenced in code section number |
EN 1081-98
Resilient Floor Coverings—Determination of the Electrical Resistance
FEMA
Washington
Standard reference number | Title | Referenced in code section number |
FIA-TB11—01
Crawlspace Construction for Buildings Located in Special Flood Hazard Areas
FM
Standard reference number | Title | Referenced in code section number |
4450 (1989)
Approval Standard for Class 1 Insulated Steel Deck Roofs—with Supplements through July 1992
4470 (2010)
Approval Standard for Class 1 Roof Covers
4474 (04)
Evaluating the Simulated Wind Uplift Resistance of Roof Assemblies
Using Static Positive and/or Negative Differential Pressures
4880 (2010)
American National Standard for Evaluating Insulated Wall or Wall and Roof/
Ceiling Assemblies, Plastic Interior Finish Materials, Plastic Exterior Building Panels,
Wall/Ceiling Coating Systems, Interior and Exterior Finish Systems
GA
Standard reference number | Title | Referenced in code section number |
GA 216—10
Application and Finishing of Gypsum Panel Products
GA 600—09
Fire-resistance Design Manual, 18th Edition
HPVA
Standard reference number | Title | Referenced in code section number |
HP-1—2009
Standard for Hardwood and Decorative Plywood
HUD
Standard reference number | Title | Referenced in code section number |
HUD 24 CFR Part 3280 (1994)
Manufactured Home Construction and Safety Standards
ICC
6th Floor
Standard reference number | Title | Referenced in code section number |
ICC/ANSI A117.1—09
Accessible and Usable Buildings and Facilities
ICC 300—07
ICC Standard on Bleachers, Folding and Telescopic Seating and Grandstands
ICC 400—07
Standard on Design and Construction of Log Structures
ICC 500—08
ICC/NSSA Standard on the Design and Construction of Storm Shelters
ICC 600—08
Standard for Residential Construction in High Wind Regions
IEBC—09
International Existing Building Code®
IECC—09
International Energy Conservation Code® (adoption includes only Section 101 of Chapter 1 and Chapters 2 through 6)
IFGC—09
International Fuel Gas Code® (including ICC Emergency Amendment changing IFGC Section 406.7)
SBCCI SSTD 11—99
Test Standard for Determining Wind Resistance of Concrete or Clay Roof Tiles
ISO
Standard reference number | Title | Referenced in code section number |
ISO 8115—86
Cotton Bales—Dimensions and Density
NAAMM
Standard reference number | Title | Referenced in code section number |
FP 1001—07
Guide Specifications for Design of Metal Flag Poles
NCMA
Standard reference number | Title | Referenced in code section number |
TEK 5—08
Details for Concrete Masonry Fire Walls
NFPA
Standard reference number | Title | Referenced in code section number |
10—10
Portable Fire Extinguishers
11—10
Low Expansion Foam
12—08
Carbon Dioxide Extinguishing Systems
12A—04
Halon 1301 Fire Extinguishing Systems
13—10
Installation of Sprinkler Systems (including TIA 10-2)
13R—10
Installation of Sprinkler Systems in Residential Occupancies Up to and Including Four Stories in Height (including TIA 10-2)
14—10
Installation of Standpipe and Hose System
16—07
Installation of Foam-water Sprinkler and Foam-water Spray Systems
17—09
Dry Chemical Extinguishing Systems
17A—09
Wet Chemical Extinguishing Systems
20—10
Installation of Stationary Pumps for Fire Protection
30—15
Flammable and Combustible Liquids Code
31—11
Installation of Oil-burning Equipment
32—07
Dry Cleaning Plants
37—10
Installation and Use of Stationary Combustion Engines and Gas Turbines
40—11
Storage and Handling of Cellulose Nitrate Film
58—11
Liquefied Petroleum Gas Code
61—08
Prevention of Fires and Dust Explosions in Agricultural and Food Product Facilities
70—14
National Electrical Code
72—10
National Fire Alarm and Signaling Code (including TIA 10-4 and TIA 10-5)
80—10
Fire Doors and Other Opening Protectives
85—07
Boiler and Combustion System Hazards Code
(Note: NFPA 8503 has been incorporated into NFPA 85)
92B—09
Smoke Management Systems in Malls, Atria and Large Spaces
99—05
Standard for Health Care Facilities
105—10
Standard for the Installation of Smoke Door Assemblies
110—10
Emergency and Standby Power Systems
111—10
Stored Electrical Energy Emergency and Standby Power Systems
120—10
Coal Preparation Plants
170—09
Standard for Fire Safety and Emergency Symbols
211—10
Chimneys, Fireplaces, Vents and Solid Fuel-burning Appliances
221—09
Standard for High challenge Fire Walls, Fire Walls, and Fire Barrier Walls
252—08
Standard Methods of Fire Tests of Door Assemblies
253—06
Test for Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat Energy Source
257—07
Standard for Fire Test for Window and Glass Block Assemblies
259—08
Test Method for Potential Heat of Building Materials
265—07
Method of Fire Tests for Evaluating Room Fire Growth Contribution of
Textile Wall Coverings on Full Height Panels and Walls
268—07
Standard Test Method for Determining Ignitibility of Exterior Wall Assemblies Using a Radiant Heat Energy Source
285—06
Standard Method of Test for the Evaluation of Flammability Characteristics of
Exterior Nonload-bearingWall Assemblies Containing Combustible Components
286—06
Standard Method of Fire Test for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth
288—07
Standard Method of Fire Tests of Floor Fire Door Assemblies Installed Horizontally in Fire-resistance-rated Floor Systems
409—11
Aircraft Hangars
418—06
Standard for Heliports
484—09
Combustible Metals
654—06
Prevention of Fire & Dust Explosions from the Manufacturing, Processing and Handling of Combustible Particulate Solids
655—07
Prevention of Sulfur Fires and Explosions
664—07
Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities
701—10
Standard Methods of Fire Tests for Flame-propagation of Textiles and Films
704—07
Standard System for the Identification of the Hazards of Materials for Emergency Response
1124—06
Manufacture, Transportation and Storage of Fireworks and Pyrotechnic Articles
2001—08
Clean Agent Fire Extinguishing Systems
PCI
Standard reference number | Title | Referenced in code section number |
MNL 124—89
Design for Fire Resistance of Precast Prestressed Concrete
MNL 128—01
Recommended Practice for Glass Fiber Reinforced Concrete Panels
PTI
Standard reference number | Title | Referenced in code section number |
PTI—2008
Standard Requirements for Analysis of Shallow Concrete Foundations on Expansive Soils, Third Edition
PTI—2008
Standard Requirements for Design of Shallow Post-tensioned Concrete Foundation on Expansive Soils, Second Edition
RMI
Standard reference number | Title | Referenced in code section number |
ANSI/MH16.1—08
Specification for Design, Testing and Utilization of Industrial Steel Storage Racks
SDI
Standard reference number | Title | Referenced in code section number |
ANSI/NC1.0—06
Standard for Noncomposite Steel Floor Deck
ANSI/RD1.0—06
Standard for Steel Roof Deck
SJI
Standard reference number | Title | Referenced in code section number |
CJ-1.0—06
Standard Specification for Composite Steel Joists, CJ-series
JG-1.1—05
Standard Specification for Joist Girders
K-1.1—05
Standard Specification for Open Web Steel Joists, K-series
LH/DLH-1.1—05
Standard Specification for Longspan Steel Joists, LH-series and Deep Longspan Steel Joists, DLH-series
SPRI
Standard reference number | Title | Referenced in code section number |
SPRI/ANSI/ES-1—03
Wind Design Standard for Edge Systems Used with Low Slope Roofing Systems
RP-4—02
Wind Design Guide for Ballasted Single-ply Roofing Systems
TIA
Standard reference number | Title | Referenced in code section number |
TIA-222-G—09
Structural Standards for Steel Antenna Towers and Antenna Supporting
Structures including-Addendum 1, 222-G-1, Dated 2007
TMS
Standard reference number | Title | Referenced in code section number |
0216—07
Standard Method for Determining Fire Resistance of Concrete and Masonry Construction Assemblies
0302—07
Standard Method for Determining the Sound Transmission Class Rating for Masonry Walls
402—08
Building Code Requirements for Masonry Structures
602—08
Specification for Masonry Structures
TPI
Standard reference number | Title | Referenced in code section number |
TPI 1—2007
National Design Standards for Metal-plate-connected Wood Truss Construction
UL
Standard reference number | Title | Referenced in code section number |
9—09
Fire Tests of Window Assemblies—with Revisions through April 2005
10A—09
Tin Clad Fire Doors—with Revisions through March 2003
10B—08
Fire Tests of Door Assemblies—with Revisions through October 2001
10C—09
Positive Pressure Fire Tests of Door Assemblies—with Revisions through November 2001
14B—08
Sliding Hardware for Standard Horizontally-mounted Tin Clad Fire Doors—with Revisions through July 2000
14C—06
Swinging Hardware for Standard Tin Clad Fire Doors Mounted Singly and in Pairs
103—10
Factory-built Chimneys, for Residential Type and Building Heating Appliances—with Revisions through June 2006
127—08
Factory-built Fireplaces—with Revisions through November 2006
199E—04
Outline of Investigation for Fire Testing of Sprinklers and Water Spray Nozzles for Protection of Deep Fat Fryers
217—06
Single and Multiple Station Smoke Alarms—with Revisions through August 2005
263—03
Standard for Fire Test of Building Construction and Materials
268—09
Smoke Detectors for Fire Protective Signaling Systems—with Revisions through January 1999
300—05
Fire Testing of Fire Extinguishing Systems for Protection of Restaurant Cooking Areas
300A—06
Extinguishing system units for residential range top cooking surfaces
305—97
Panic Hardware
325—02
Door, Drapery, Gate, Louver and Window Operations and Systems—with Revisions through February 2006
555—2006
Fire Dampers
555C—2006
Ceiling Dampers
555S—99
Smoke Dampers—with Revisions through July 2006
580—2006
Test for Uplift Resistance of Roof Assemblies
641—95
Type L Low-temperature Venting Systems—with Revisions through August 2005
710B—04
Recirculating Systems—with Revisions through April 2006
723—08
Standard for Test for Surface Burning Characteristics of Building Materials—with Revisions through May 2005
790—04
Standard Test Methods for Fire Tests of Roof Coverings
793—08
Standards for Automatically Operated Roof Vents for Smoke and Heat—with Revisions through April 2004
864—03
Standards for Control Units and Accessories for Fire Alarm Systems—with Revisions through March 2006
924—06
Standard for Safety Emergency Lighting and Power Equipment
1040—96
Fire Test of Insulated Wall Construction—with Revisions through June 2001
1256—02
Fire Test of Roof Deck Construction—with Revisions through January 2007
1479—03
Fire Tests of Through-penetration Firestops—with Revisions through April 2007
1482—10
Solid-fuel-type Room Heater—with Revisions through November 2006
1715—97
Fire Test of Interior Finish Material—with Revisions through March 2004
1777—07
Chimney Liners
1784—01
Air Leakage Tests of Door Assemblies—with Revisions through December 2004
1897—04
Uplift Tests for Roof Covering Systems
1975—06
Fire Test of Foamed Plastics Used for Decorative Purposes
1994—04
Standard for Luminous Egress Path Marking Systems—with Revisions through February 2005
2017—08
Standards for General-purpose Signaling Devices and Systems—with Revisions through August 2005
2079—04
Tests for Fire Resistance of Building Joint Systems—with Revisions through March 2006
2200—12
Stationary Engine Generator Assemblies—with Revisions through July 2004
ULC
Standard reference number | Title | Referenced in code section number |
CAN/ULC S102.2—2010
Standard Method of Test for Surface Burning Characteristics of Flooring,
Floor Coverings and Miscellaneous Materials and Assemblies—with 2000 Revisions
USC
Washington
Standard reference number | Title | Referenced in code section number |
10 USC Sections 18233(A)(1) and 18237—1994
18 USC Part 1, Ch.40
Importation, Manufacture, Distribution and Storage of Explosive Materials
WDMA
Standard reference number | Title | Referenced in code section number |
AAMA/WDMA/CSA 101/I.S.2/A440—08
Specifications for Windows, Doors and Unit Skylights
WRI
Standard reference number | Title | Referenced in code section number |
WRI/CRSI—81
Design of Slab-on-ground Foundations—with 1996 Update